ATM-MIB Download

atmInterfaceConfTable

This table contains ATM local interface configuration parameters, one entry per ATM interface port.

atmInterfaceConfEntry

This list contains ATM interface configuration parameters and state variables and is indexed by ifIndex values of ATM interfaces.

atmInterfaceMaxVpcs

The maximum number of VPCs (PVPCs and SVPCs) supported at this ATM interface. At the ATM UNI, the maximum number of VPCs (PVPCs and SVPCs) ranges from 0 to 256 only.

atmInterfaceMaxVccs

The maximum number of VCCs (PVCCs and SVCCs) supported at this ATM interface.

atmInterfaceConfVpcs

The number of VPCs (PVPC, Soft PVPC and SVPC) currently in use at this ATM interface. It includes the number of PVPCs and Soft PVPCs that are configured at the interface, plus the number of SVPCs that are currently established at the interface. At the A ...

atmInterfaceConfVccs

The number of VCCs (PVCC, Soft PVCC and SVCC) currently in use at this ATM interface. It includes the number of PVCCs and Soft PVCCs that are configured at the interface, plus the number of SVCCs that are currently established at the interface.

atmInterfaceMaxActiveVpiBits

The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI bits configured for use ranges from 0 to 8 only.

atmInterfaceMaxActiveVciBits

The maximum number of active VCI bits configured for use at this ATM interface.

atmInterfaceIlmiVpi

The VPI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface.

atmInterfaceIlmiVci

The VCI value of the VCC supporting the ILMI at this ATM interface. If the values of atmInterfaceIlmiVpi and atmInterfaceIlmiVci are both equal to zero then the ILMI is not supported at this ATM interface.

atmInterfaceAddressType

The type of primary ATM address configured for use at this ATM interface.

atmInterfaceAdminAddress

The primary address assigned for administrative purposes, for example, an address associated with the service provider side of a public network UNI (thus, the value of this address corresponds with the value of ifPhysAddress at the host side). If this int ...

atmInterfaceMyNeighborIpAddress

The IP address of the neighbor system connected to the far end of this interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network management information concerning the operati ...

atmInterfaceMyNeighborIfName

The textual name of the interface on the neighbor system on the far end of this interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the value of this object must be identical ...

atmInterfaceCurrentMaxVpiBits

The maximum number of VPI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVpiBits, and the atmInterfaceMaxActiveVpiBits of the interface's UNI/NNI peer. If the interface does not negotiate with its p ...

atmInterfaceCurrentMaxVciBits

The maximum number of VCI Bits that may currently be used at this ATM interface. The value is the minimum of atmInterfaceMaxActiveVciBits, and the atmInterfaceMaxActiveVciBits of the interface's UNI/NNI peer. If the interface does not negotiate with its p ...

atmInterfaceSubscrAddress

The identifier assigned by a service provider to the network side of a public network UNI. If this interface has no assigned service provider address, or for other interfaces this is an octet string of zero length.

atmInterfaceDs3PlcpTable

This table contains ATM interface DS3 PLCP parameters and state variables, one entry per ATM interface port.

atmInterfaceDs3PlcpEntry

This list contains DS3 PLCP parameters and state variables at the ATM interface and is indexed by the ifIndex value of the ATM interface.

atmInterfaceDs3PlcpSEFSs

The number of DS3 PLCP Severely Errored Framing Seconds (SEFS). Each SEFS represents a one-second interval which contains one or more SEF events.

atmInterfaceDs3PlcpAlarmState

This variable indicates if there is an alarm present for the DS3 PLCP. The value receivedFarEndAlarm means that the DS3 PLCP has received an incoming Yellow Signal, the value incomingLOF means that the DS3 PLCP has declared a loss of frame (LOF) failure ...

atmInterfaceDs3PlcpUASs

The counter associated with the number of Unavailable Seconds encountered by the PLCP.

atmInterfaceTCTable

This table contains ATM interface TC Sublayer parameters and state variables, one entry per ATM interface port.

atmInterfaceTCEntry

This list contains TC Sublayer parameters and state variables at the ATM interface and is indexed by the ifIndex value of the ATM interface.

atmInterfaceOCDEvents

The number of times the Out of Cell Delineation (OCD) events occur. If seven consecutive ATM cells have Header Error Control (HEC) violations, an OCD event occurs. A high number of OCD events may indicate a problem with the TC Sublayer.

atmInterfaceTCAlarmState

This variable indicates if there is an alarm present for the TC Sublayer. The value lcdFailure(2) indicates that the TC Sublayer is currently in the Loss of Cell Delineation (LCD) defect maintenance state. The value noAlarm(1) indicates that the TC Subl ...

atmTrafficDescrParamTable

This table contains information on ATM traffic descriptor type and the associated parameters.

atmTrafficDescrParamEntry

This list contains ATM traffic descriptor type and the associated parameters.

atmTrafficDescrParamIndex

This object is used by the virtual link table (i.e., VPL or VCL table) to identify the row of this table. When creating a new row in the table the value of this index may be obtained by retrieving the value of atmTrafficDescrParamIndexNext.

atmTrafficDescrType

The value of this object identifies the type of ATM traffic descriptor. The type may indicate no traffic descriptor or traffic descriptor with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of ...

atmTrafficDescrParam1

The first parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.

atmTrafficDescrParam2

The second parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.

atmTrafficDescrParam3

The third parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.

atmTrafficDescrParam4

The fourth parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.

atmTrafficDescrParam5

The fifth parameter of the ATM traffic descriptor used according to the value of atmTrafficDescrType.

atmTrafficQoSClass

The value of this object identifies the QoS Class. Four Service classes have been specified in the ATM Forum UNI Specification: Service Class A: Constant bit rate video and Circuit emulation Service Class B: Variable bit rate video/audio Service Class C: ...

atmTrafficDescrRowStatus

This object is used to create a new row or modify or delete an existing row in this table.

atmServiceCategory

The ATM service category.

atmTrafficFrameDiscard

If set to 'true', this object indicates that the network is requested to treat data for this connection, in the given direction, as frames (e.g. AAL5 CPCS_PDU's) rather than as individual cells. While the precise implementation is network-specific, this ...

atmVplTable

The Virtual Path Link (VPL) table. A bi-directional VPL is modeled as one entry in this table. This table can be used for PVCs, SVCs and Soft PVCs. Entries are not present in this table for the VPIs used by entries in the atmVclTable.

atmVplEntry

An entry in the VPL table. This entry is used to model a bi-directional VPL. To create a VPL at an ATM interface, either of the following procedures are used: Negotiated VPL establishment (1) The management application creates a VPL entry in the atmVplTa ...

atmVplVpi

The VPI value of the VPL.

atmVplAdminStatus

This object is instanciated only for a VPL which terminates a VPC (i.e., one which is NOT cross-connected to other VPLs). Its value specifies the desired administrative state of the VPL.

atmVplOperStatus

The current operational status of the VPL.

atmVplLastChange

The value of sysUpTime at the time this VPL entered its current operational state.

atmVplReceiveTrafficDescrIndex

The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the receive direction of the VPL.

atmVplTransmitTrafficDescrIndex

The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the transmit direction of the VPL.

atmVplCrossConnectIdentifier

This object is instantiated only for a VPL which is cross-connected to other VPLs that belong to the same VPC. All such associated VPLs have the same value of this object, and all their cross-connections are identified either by entries that are indexed ...

atmVplRowStatus

This object is used to create, delete or modify a row in this table. To create a new VCL, this object is initially set to 'createAndWait' or 'createAndGo'. This object should not be set to 'active' unless the following columnar objects have been set to t ...

atmVplCastType

The connection topology type.

atmVplConnKind

The use of call control.

atmVclTable

The Virtual Channel Link (VCL) table. A bi-directional VCL is modeled as one entry in this table. This table can be used for PVCs, SVCs and Soft PVCs.

atmVclEntry

An entry in the VCL table. This entry is used to model a bi-directional VCL. To create a VCL at an ATM interface, either of the following procedures are used: Negotiated VCL establishment (1) The management application creates a VCL entry in the atmVclTab ...

atmVclVpi

The VPI value of the VCL.

atmVclVci

The VCI value of the VCL.

atmVclAdminStatus

This object is instanciated only for a VCL which terminates a VCC (i.e., one which is NOT cross-connected to other VCLs). Its value specifies the desired administrative state of the VCL.

atmVclOperStatus

The current operational status of the VCL.

atmVclLastChange

The value of sysUpTime at the time this VCL entered its current operational state.

atmVclReceiveTrafficDescrIndex

The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.

atmVclTransmitTrafficDescrIndex

The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCL.

atmVccAalType

An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL is in use. The type of AAL used on this VCC. The AAL type includes AAL1, AAL2, AAL3/4, and AAL5. The other(4) may be user-defined AAL type. The unknown ...

atmVccAal5CpcsTransmitSduSize

An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the transmit direction of this VCC.

atmVccAal5CpcsReceiveSduSize

An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The maximum AAL5 CPCS SDU size in octets that is supported on the receive direction of this VCC.

atmVccAal5EncapsType

An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the AAL5 SSCS layer. The definitions reference RFC 1483 Multiprotocol Encapsulation over ATM AAL5 a ...

atmVclCrossConnectIdentifier

This object is instantiated only for a VCL which is cross-connected to other VCLs that belong to the same VCC. All such associated VCLs have the same value of this object, and all their cross-connections are identified either by entries that are indexed ...

atmVclRowStatus

This object is used to create, delete or modify a row in this table. To create a new VCL, this object is initially set to 'createAndWait' or 'createAndGo'. This object should not be set to 'active' unless the following columnar objects have been set to t ...

atmVclCastType

The connection topology type.

atmVclConnKind

The use of call control.

atmVpCrossConnectIndexNext

This object contains an appropriate value to be used for atmVpCrossConnectIndex when creating entries in the atmVpCrossConnectTable. The value 0 indicates that no unassigned entries are available. To obtain the atmVpCrossConnectIndex value for a new entr ...

atmVpCrossConnectTable

The ATM VP Cross Connect table for PVCs. An entry in this table models two cross-connected VPLs. Each VPL must have its atmConnKind set to pvc(1).

atmVpCrossConnectEntry

An entry in the ATM VP Cross Connect table. This entry is used to model a bi-directional ATM VP cross-connect which cross-connects two VPLs. Step-wise Procedures to set up a VP Cross-connect Once the entries in the atmVplTable are created, the following p ...

atmVpCrossConnectIndex

A unique value to identify this VP cross-connect. For each VPL associated with this cross-connect, the agent reports this cross-connect index value in the atmVplCrossConnectIdentifier attribute of the corresponding atmVplTable entries.

atmVpCrossConnectLowIfIndex

The ifIndex value of the ATM interface for this VP cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex value than the other ATM interface identified in the same atmVpCrossConnectEntry.

atmVpCrossConnectLowVpi

The VPI value at the ATM interface associated with the VP cross-connect that is identified by atmVpCrossConnectLowIfIndex.

atmVpCrossConnectHighIfIndex

The ifIndex value of the ATM interface for this VP cross-connect. The term high implies that this ATM interface has the numerically higher ifIndex value than the other ATM interface identified in the same atmVpCrossConnectEntry.

atmVpCrossConnectHighVpi

The VPI value at the ATM interface associated with the VP cross-connect that is identified by atmVpCrossConnectHighIfIndex.

atmVpCrossConnectAdminStatus

The desired administrative status of this bi-directional VP cross-connect.

atmVpCrossConnectL2HOperStatus

The operational status of the VP cross-connect in one direction; (i.e., from the low to high direction).

atmVpCrossConnectH2LOperStatus

The operational status of the VP cross-connect in one direction; (i.e., from the high to low direction).

atmVpCrossConnectL2HLastChange

The value of sysUpTime at the time this VP cross-connect entered its current operational state in the low to high direction.

atmVpCrossConnectH2LLastChange

The value of sysUpTime at the time this VP cross-connect entered its current operational in the high to low direction.

atmVpCrossConnectRowStatus

The status of this entry in the atmVpCrossConnectTable. This object is used to create a cross-connect for cross-connecting VPLs which are created using the atmVplTable or to change or delete an existing cross-connect. This object must be initially set to ...

atmVcCrossConnectIndexNext

This object contains an appropriate value to be used for atmVcCrossConnectIndex when creating entries in the atmVcCrossConnectTable. The value 0 indicates that no unassigned entries are available. To obtain the atmVcCrossConnectIndex value for a new entr ...

atmVcCrossConnectTable

The ATM VC Cross Connect table for PVCs. An entry in this table models two cross-connected VCLs. Each VCL must have its atmConnKind set to pvc(1).

atmVcCrossConnectEntry

An entry in the ATM VC Cross Connect table. This entry is used to model a bi-directional ATM VC cross-connect cross-connecting two end points. Step-wise Procedures to set up a VC Cross-connect Once the entries in the atmVclTable are created, the following ...

atmVcCrossConnectIndex

A unique value to identify this VC cross-connect. For each VCL associated with this cross-connect, the agent reports this cross-connect index value in the atmVclCrossConnectIdentifier attribute of the corresponding atmVclTable entries.

atmVcCrossConnectLowIfIndex

The ifIndex value of the ATM interface for this VC cross-connect. The term low implies that this ATM interface has the numerically lower ifIndex value than the other ATM interface identified in the same atmVcCrossConnectEntry.

atmVcCrossConnectLowVpi

The VPI value at the ATM interface associated with the VC cross-connect that is identified by atmVcCrossConnectLowIfIndex.

atmVcCrossConnectLowVci

The VCI value at the ATM interface associated with this VC cross-connect that is identified by atmVcCrossConnectLowIfIndex.

atmVcCrossConnectHighIfIndex

The ifIndex value for the ATM interface for this VC cross-connect. The term high implies that this ATM interface has the numerically higher ifIndex value than the other ATM interface identified in the same atmVcCrossConnectEntry.

atmVcCrossConnectHighVpi

The VPI value at the ATM interface associated with the VC cross-connect that is identified by atmVcCrossConnectHighIfIndex.

atmVcCrossConnectHighVci

The VCI value at the ATM interface associated with the VC cross-connect that is identified by atmVcCrossConnectHighIfIndex.

atmVcCrossConnectAdminStatus

The desired administrative status of this bi-directional VC cross-connect.

atmVcCrossConnectL2HOperStatus

The current operational status of the VC cross-connect in one direction; (i.e., from the low to high direction).

atmVcCrossConnectH2LOperStatus

The current operational status of the VC cross-connect in one direction; (i.e., from the high to low direction).

atmVcCrossConnectL2HLastChange

The value of sysUpTime at the time this VC cross-connect entered its current operational state in low to high direction.

atmVcCrossConnectH2LLastChange

The value of sysUpTime at the time this VC cross-connect entered its current operational state in high to low direction.

atmVcCrossConnectRowStatus

The status of this entry in the atmVcCrossConnectTable. This object is used to create a new cross-connect for cross-connecting VCLs which are created using the atmVclTable or to change or delete existing cross-connect. This object must be initially set t ...

aal5VccTable

This table contains AAL5 VCC performance parameters.

aal5VccEntry

This list contains the AAL5 VCC performance parameters and is indexed by ifIndex values of AAL5 interfaces and the associated VPI/VCI values.

aal5VccVpi

The VPI value of the AAL5 VCC at the interface identified by the ifIndex.

aal5VccVci

The VCI value of the AAL5 VCC at the interface identified by the ifIndex.

aal5VccCrcErrors

The number of AAL5 CPCS PDUs received with CRC-32 errors on this AAL5 VCC at the interface associated with an AAL5 entity.

aal5VccSarTimeOuts

The number of partially re-assembled AAL5 CPCS PDUs which were discarded on this AAL5 VCC at the interface associated with an AAL5 entity because they were not fully re-assembled within the required time period. If the re-assembly timer is not supported, ...

aal5VccOverSizedSDUs

The number of AAL5 CPCS PDUs discarded on this AAL5 VCC at the interface associated with an AAL5 entity because the AAL5 SDUs were too large.

atmTrafficDescrParamIndexNext

This object contains an appropriate value to be used for atmTrafficDescrParamIndex when creating entries in the atmTrafficDescrParamTable. The value 0 indicates that no unassigned entries are available. To obtain the atmTrafficDescrParamIndex value for a ...

atmInterfaceDs3PlcpGroup

A collection of objects providing information about DS3 PLCP layer at an ATM interface.

atmInterfaceTCGroup

A collection of objects providing information about TC sublayer at an ATM interface.

aal5VccGroup

A collection of objects providing AAL5 configuration and performance statistics of a VCC.

atmInterfaceConfGroup2

A collection of objects providing configuration information about an ATM interface.

atmTrafficDescrGroup2

A collection of objects providing information about ATM traffic descriptor type and the associated parameters.

atmVpcTerminationGroup2

A collection of objects providing information about a VPL at an ATM interface which terminates a VPC (i.e., one which is NOT cross-connected to other VPLs).

atmVccTerminationGroup2

A collection of objects providing information about a VCL at an ATM interface which terminates a VCC (i.e., one which is NOT cross-connected to other VCLs).

atmVplCrossConnectGroup

A collection of objects providing information about the VPLs that are cross-connected together.

atmVpPvcCrossConnectGroup

A collection of objects providing information about a VP cross-connect for PVCs. These objects are not used for Soft PVCs or SVCs.

atmVclCrossConnectGroup

A collection of objects providing information about the VCLs that are cross-connected together.

atmVcPvcCrossConnectGroup

A collection of objects providing information about a VC cross-connect for PVCs. These objects are not used for Soft PVCs or SVCs.

atmInterfaceConfGroup

A collection of objects providing configuration information about an ATM interface.

atmTrafficDescrGroup

A collection of objects providing information about ATM traffic descriptor type and the associated parameters.

atmVpcTerminationGroup

A collection of objects providing information about a VPL at an ATM interface which terminates a VPC (i.e., one which is NOT cross-connected to other VPLs).

atmVccTerminationGroup

A collection of objects providing information about a VCL at an ATM interface which terminates a VCC (i.e., one which is NOT cross-connected to other VCLs).

atmVpCrossConnectGroup

A collection of objects providing information about a VP cross-connect and the associated VPLs that are cross-connected together.

atmVcCrossConnectGroup

A collection of objects providing information about a VC cross-connect and the associated VCLs that are cross-connected together.