CISCO-ATM-SWITCH-FR-IWF-MIB Download

casfTrafficDescrTable

This table contains a set of self-consistent Frame Relay traffic parameters. It is intended to be used to create Frame Relay to ATM interworking connections, hence a ATM traffic service category is also included. An entry in this table is associated with ...

casfTrafficDescrEntry

Describes a traffic descriptor that is used by Frame Relay connections.

casfTrafficDescrIndex

Uniquely identifies a row in this table.

casfTrafficDescrCIR

The value of the Committed Information Rate (CIR) parameter.

casfTrafficDescrBc

The value of the Committed Burst Size (Bc) parameter.

casfTrafficDescrBe

The value of the Excess Burst Size (Be) parameter.

casfTrafficDescrPIR

The value of the Peak Information Rate (PIR) parameter.

casfTrafficDescrServCategory

The service category, as defined for ATM.

casfTrafficDescrAtmIndex

The index of the equivalent entry in the atmTrafficDescrParamTable.

casfTrafficDescrRowStatus

Used to create, delete and modify this row. None of the columnar values (other than this one) can be modified while the row is active.

casfVcEndptTable

This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agent creates a corresponding entry in the atmVclTable of ATM-MIB, to represent the configuration on ...

casfVcEndptEntry

Models a bidirectional Frame Relay VC end-point. The ifIndex identifies an ifTable entry for a Frame Relay interface on this device.

casfVcEndptDlci

The value of the Data Link Connection Identifier (DLCI) which identifies this connection end-point.

casfVcEndptRxTrafficDescrRow

Identifies the entry in the casfTrafficDescrTable which applies to the receive direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connections), this object points to the desired traffic pa ...

casfVcEndptTxTrafficDescrRow

Identifies the entry in the casfTrafficDescrTable which applies to the transmit direction at this connection end-point. For connections that negotiate traffic parameters through signaling (e.g. ABR connections), this object points to the desired traffic p ...

casfVcEndptRxNegTrafficDescrRow

Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the receive direction of this connection end-point. This object is not instantiated if this is not the calling side of a soft VC, or if there is no t ...

casfVcEndptTxNegTrafficDescrRow

Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the transmit direction of this connection endpoint. This object is not instantiated if this is not the calling side of a soft VC, or if there is no t ...

casfVcEndptConnKind

The connection kind. The value can be set prior to the row becoming 'active'. To create a pvc connection endpoint, set this value to pvc(1). To create a soft VC connection endpoint, set this value to spvcInitiator(4), and specify the value of casfVcEndptS ...

casfVcEndptIwfType

The type of the interworking function. The value can be set prior to the row becoming 'active'.

casfVcEndptClpMode

Specifies how to map from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side. For network interworking, clpIfDe(1) corresponds to Mode 1 as defined in FRF.5, section 4.4.1. clpIsZero(2) and clpIsOne( ...

casfVcEndptDeMode

Specifies how to map from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. See the Frame Relay Forum specifications FRF.5 and FRF.8 for definitions of Mode 1 and Mode 2. For network interworking, ...

casfVcEndptUpcMode

Specifies the action taken by Usage Parameter Control (UPC) at the ingress port.

casfVcEndptSpvcRemoteAddr

The ATM address of the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4). The agent will return an inconsistentValue error on sets if the value of casfVcEndptCon ...

casfVcEndptSpvcRemoteType

The type of the remote end of the soft VC. This object is instantiated only if the value of casfVcEndptConnKind is spvcInitiator(4) or spvcTarget(5). The agent will return an inconsistentValue error on sets if the value of casfVcEndptConnKind is other tha ...

casfVcEndptSpvcRemoteDlci

The DLCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is frameRelay(2). The object is i ...

casfVcEndptSpvcRemoteVpi

The VPI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is atm(3). The object is instantia ...

casfVcEndptSpvcRemoteVci

The VCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcInitiator(4), and the value of casfVcEndptSpvcRemoteType is atm(3). The object is instantia ...

casfVcEndptCreationTime

The time when this row was created.

casfVcEndptRcvdSigStatus

The value of this object identifies the PVC status received via the local in-channel signaling procedures for this PVC end-point. This object is only pertinent for interfaces that perform the bidirectional procedures. For user-to-network network side proc ...

casfVcEndptRowStatus

Used to create, modify or delete this row.

casfVcSignalStandardCalledIe

Specifies whether or not to signal the standard (from the ATM-Forum PNNI Soft PVC Addendum) format of the Called Soft PVC IE, as opposed to the proprietary encoding we have used for the network-interworking case to a frame-relay destination.

casfFrLmiTable

This table contains frame relay Local Management Interface (LMI) parameters and counters. There is one entry for each frame relay interface. Entries come and go in this table as frame relay interfaces are created and deleted in the device.

casfFrLmiEntry

Frame relay LMI objects for a particular frame relay interface, which is identified by the ifIndex value in the INDEX clause.

casfFrLmiProtocol

Identifies the Local In-Channel Signaling Protocol that is used for this frame relay port.

casfFrLmiType

Identifies the Local In-Channel Signaling Procedure that is used for this frame relay port. A dte performs only user-side procedures. A dce performs only network-side procedures. An nni performs bidirectional procedures.

casfFrLmiUserN391

Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage.

casfFrLmiUserN392

The maximum number of unanswered Status Enquiries the device shall accept before declaring the interface down.

casfFrLmiUserN393

The number of status polling intervals over which the error threshold is counted. For example, if within N393 number of events the device receives N392 number of errors, the interface is marked as down.

casfFrLmiUserT391

The number of seconds between successive status enquiry messages.

casfFrLmiNetN392

The value of the network-side error threshold for this frame relay port.

casfFrLmiNetN393

The value of the network-side monitored events count for this frame relay port. If, within N393 number of events, the network-side receives N392 number of errors, the interface is marked as down.

casfFrLmiNetT392

The value of the network-side polling verification timer for this frame relay port.

casfFrLmiEnquiryIns

Number of Status Enquiry messages received.

casfFrLmiEnquiryOuts

Number of Status Enquiry messages sent.

casfFrLmiStatusIns

Number of Status messages received.

casfFrLmiStatusOuts

Number of Status messages sent.

casfFrLmiStatusTimeouts

Number of times when timeout occurred on waiting for Status message

casfFrLmiStatusEnqTimeouts

Number of times when timeout occurred on waiting for Status Enquiry message

casfConfIfTable

Contains an entry for each Frame Relay interface that supports FR-ATM interworking connections. An entry contains interworking related parameters for the interface.

casfConfIfEntry

Configuration parameters for interworking at a Frame Relay interface.

casfConfIfAtmAddress

The ATM Address that identifies this interface. This address can be used to setup soft VC's to this interface over an ATM network.

casfConfIfUpcIntent

Specifies the default Usage Parameter Control (UPC) action to use at this interface for connections that do not explicitly specify a UPC action.

casfConfIfBcDefault

Specifies the default Committed Burst Size (Bc) value to use at this interface for connections that do not explicitly specify the value of Bc.

casfConfIfCledSpvcDeModeDef

Specifies the default mapping from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. This is used when receiving a soft PVC Setup using the standard encoding of the called Soft PVC IE. Otherwise a ...

casfConfIfCledSpvcClpModeDef

Specifies the default mapping from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side.This is used when receiving a soft PVC Setup using the standard encoding of the called Soft PVC IE. Otherwise a p ...

casfVcCountTable

A table containing counters at Frame Relay connection end-points. Entries in this table are created and deleted whenever corresponding entries in the casfVcEndptTable are created and deleted.

casfVcCountEntry

Counters at a Frame Relay connection end-point, which is identified by the ifIndex of the Frame Relay interface and the DLCI number.

casfVcCountReceivedFrames

Number of frames received.

casfVcCountReceivedOctets

Number of octets received. This counter counts octets from the beginning of the frame relay header field to the end of user data.

casfVcCountReceivedFECNs

Number of frames received from the network with the FECN (Forward Explicit Congestion Notification) bit set.

casfVcCountReceivedBECNs

Number of frames received from the network with the BECN (Backward Explicit Network Congestion) bit set.

casfVcCountReceivedDEs

Number of frames received with the Discard Eligibility (DE) bit set.

casfVcCountInDiscards

Number of frames received that were discarded at ingress. Possible reasons are policing, congestion.

casfVcCountOutDiscards

Number of frames that were to be transmitted but were discarded. Possible reasons are policing, lack of buffers.

casfVcCountSentFrames

Number of frames sent.

casfVcCountSentOctets

Number of octets sent. This counter counts octets from the beginning of the frame relay header field to the end of user data.

casfVcCountSentFECNs

Number of frames that were sent with the FECN bit set.

casfVcCountSentBECNs

Number of frames sent with the BECN bit set.

casfVcCountSentDEs

Number of frames sent with the DE bit set.

casfVcCountTaggedFECNs

Number of frames for which the switch set the FECN bit.

casfVcCountTaggedBECNs

Number of frames for which the switch set the BECN bit.

casfVcCountTaggedDEs

Number of frames for which the switch set the DE bit.

casfVcIwfCountTable

This table contains counters at the Frame Relay endpoint of FR-ATM interworking connections. There is an entry in this table corresponding to each entry in casfVcEndptTable.

casfVcIwfCountEntry

A set of counters at the Frame Relay endpoint of a FR-ATM interworking connection.

casfVcIwfCountInUnknownProts

Frames received with unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count will remain at zero.

casfVcIwfCountOutUnknownProts

Outbound frames that were not transmitted because they contained an unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections, this count will remain at zero.

casfVcIwfCountReassemblyTimeouts

The number of frames which could not be completely reassembled due to a reassembly timeout, and were thus discarded before being transmitted on this connection.

casfVcIwfCountLengthErrors

The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU trailer length fields did not match the actual PDU length, and were thus discarded.

casfVcIwfCountCrcErrors

The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU had CRC errors, and were thus discarded.

casfVcIwfCountTotalDiscardFrames

The number of frames intended to be transmitted on this connection that were discarded due to any reason including those described in other objects in this table (e.g., frames that were discarded because insufficient buffer space was available for reassem ...

casfFAMapTable

This table provides mapping from a DLCI on a Frame Relay interface to a VPI/VCI on an internal ATM interface.

casfFAMapEntry

Given the ifIndex of a frame relay interface, and a DLCI on that interface, this entry provides the ifIndex and VPI/VCI on the corresponding internal atm interface.

casfFAMapDlci

The DLCI value.

casfFAMapInternalAtmInterface

The ifIndex of the internal ATM interface to which this DLCI is mapped.

casfFAMapInternalAtmVpi

The VPI value to which this DLCI is mapped.

casfFAMapInternalAtmVci

The VCI value to which this DLCI is mapped.

casfAFMapTable

This table provides mapping from an atmVclEntry on an internal ATM internal to a casfVcEndptEntry on a Frame Relay interface.

casfAFMapEntry

Given the ifIndex of an internal ATM interface, and VPI/VCI, provides the ifIndex of a Frame Relay interface and DLCI, if such mapping exists. The value of ifType for an internal ATM interface is propVirtual(53). For every such interface on the switch, th ...

casfAFMapAtmVpi

The VPI value of the Virtual Channel Link (VCL) on the ATM interface.

casfAFMapAtmVci

The VCI value of the Virtual Channel Link (VCL) on the ATM interface.

casfAFMapFrIndex

The ifIndex of the frame relay interface that this VCL maps to.

casfAFMapFrDlci

The DLCI on the frame relay interface that this VCL maps to.

ciscoAtmSFrIwfConfConnGroup

A collection of objects which allow configuration of FR-ATM connections on an ATM switch.

ciscoAtmSFrIwfLmiGroup

A collection of objects for configuring and monitoring LMI on an FR interface.

ciscoAtmSFrIwfConfIfGroup

A collection of objects which allow configuration of interworking related parameters on an FR interface.

ciscoAtmSFrIwfVcStatsGroup

A collection of counters at FR VC end-points.

ciscoAtmSFrIwfVcIwStatsGroup

A collection of counters related to FR-ATM interworking at FR VC end-points.

ciscoAtmSFrIwfMappingGroup

A collection of objects that describe the mapping from a FR connection end-point to an ATM VCL, and vice versa.