CISCO-CABLE-AVAILABILITY-MIB Download

ccaHCCPVersion

The current version of HCCP features. others(1) : Any other HCCP Version other than the following list. version1(2) : HCCP Version 1.0 supports for 1+1 Availability. (1 RF MAC protecting 1 RF MAC without load sharing on the same upstream and downstream ...

ccaHCCPGroupTable

This table contains information of the HCCP groups on the CMTS. A HCCP group consists of a set of Working along with a Protect and each group is identified by a unique group ID number. Only members within a group are allowed to communicate with each other ...

ccaHCCPGroupEntry

A set of attributes of a HCCP group on the CMTS. An entry in this table exists for each configured HCCP group on the CMTS.

ccaHCCPGroupID

Identification of the HCCP protection group. Only members of the same group talk to each other via HCCP messaging.

ccaHCCPGroupAuthentication

The value of this object specifies the type of authentication method used. none(1) : No authentication is performed on that group. md5(2) : The MD5 Message Digest algorithm. text(3) : Authentication based on a textual string.

ccaHCCPGroupAuthKeyChain

This object is the name of a globally configured key chain. It is used to enable authentication and determine the set of keys which may be used on a particular group. If ccaHCCPGroupAuthentication is text(3), it is used as the authentication password. If ...

ccaHCCPGroupHelloTime

Hello time is the interval(in milliseconds) between consecutive HELLO messages. HELLO is a one-way message in HCCP sent from Protect to all Working in the group. It indicates that Protect is ready to receive data and expects HELLO_ACK. HELLO message indic ...

ccaHCCPGroupHoldTime

Hold time is the interval(in milliseconds) between the time of receiving the last HELLO ACK message and the time to assume that the cable interface is out of service. In the case of Working, it is the interval in milliseconds between the time when the Wor ...

ccaHCCPGroupRevertEnable

Enable or disable the Protect to revert switchover after Working is restored to operation. It can be disabled (default) if user wants to perform some tests before revert switching.

ccaHCCPGroupProtectIpAddrType

The type of internet address of ccaHCCPGroupProtectIpAddress.

ccaHCCPGroupProtectIpAddress

The IP address of the Protect interface for the group that sends the HELLO message.

ccaHCCPGroupIfTable

This table provides the mapping of the RF MAC interfaces on the CMTS to its functionality in the HCCP group. It indicates if the RF MAC interface has been configured as Protect or as a Working.It provides interface specific configuration and state informa ...

ccaHCCPGroupIfEntry

A mapping of a RF MAC interface to its configured functionality as Protect or Working. It provides interface specific configuration and state information as well as statistics. Entries in this table exist for each ifEntry with ifType of docsCableUpstream( ...

ccaHCCPGroupIfStatus

The value of this object identifies if the interface is functioning as Working or Protect in the HCCP group.

ccaHCCPGroupIfRevertTime

Revert time used by Working specifies the time interval to wait before automatic revert switching. Within that time interval, manual switchover is allowed to happen.

ccaHCCPGroupIfTrackEnable

Enable or disable failover based on interface state. The interface can be any interface on the router, which is monitored by keep alive timer. If it is set to true, ccaHCCPGroupTrackInterfaceTable contains the list of interfaces that are being tracked. By ...

ccaHCCPGroupIfState

The current state of the HCCP group. The members can either be forwarding traffic or blocking all traffic.

ccaHCCPGroupIfLastSwitchReason

The reason for last switch. none(1) : No switchover has occurred. holdTimeExpire(2) : Occurs when HCCP fails to hear HELLO/HELLO_ACK and the hold time expires. hwIfDown(3) : Occurs when the hardware interface is down. (eg shut/no shut) ...

ccaHCCPGroupIfOnTransitions

Number of times the value of ccaHCCPGroupIfState transitioned from 'blocking' to 'forwarding'.

ccaHCCPGroupIfOffTransitions

Number of times the value of ccaHCCPGroupIfState transitioned from 'forwarding' to 'blocking'.

ccaHCCPGroupTrackInterfaceTable

This table contains the attributes of all the interfaces that are being tracked by this group. The interface can be any interface on the chassis, which is monitored by a keep alive timer.

ccaHCCPGroupTrackInterfaceEntry

A set of attributes of an interfaces being tracked within a group.

ccaHCCPGroupTrackIfID

The value of this object uniquely identifies an interface that is being tracked within this group.

ccaHCCPGroupTrackIfDescr

A textual string containing information about the interface that is being tracked. This corresponds to the ifDescr of the tracked interface.

ccaHCCPMemberTable

This table contains the attributes of HCCP members. Each RF MAC interface configured for HCCP is called a HCCP member. Entries in this table are created for all members. In the case of Protect, it gives information of all the Working members under it's pr ...

ccaHCCPMemberEntry

A configurable attributes of a HCCP member within a group.

ccaHCCPMemberID

The value of this object identifies the Working member's ID inside a group. Members within the same group are uniquely identified by this ID. The ID can be reused outside the group.

ccaHCCPMemberIpAddrType

The type of internet address of ccaHCCPMemberIpAddress.

ccaHCCPMemberIpAddress

The IP address of the member. If the member functions as Working it represents an IP address on its interface. However in case of Protect, it represents IP address of the Working member that are being protected.

ccaHCCPMemberState

The current status of to this HCCP group member. If the RF MAC interface is Working, this represents the status of the Working member. active(1) : Working member is forwarding traffic. standby(2) : Working member is blocking traffic. If the RF ...

ccaHCCPMemberSwitchNow

This object is used to initiate the switchover. When it is set to true(1) and this interface is Protect, it will cause the switchover to specified Working member. When it is set to true(1), and if this interface is Working, it will cause the switchover to ...

ccaHCCPMemChanSwitchTable

This is an adjunct to ccaHCCPMemberTable. It provides information of HCCP member channel switches. It specifies the RF channel switch type, the RF switch over group and the RF switch module. The upconvertor IP addresses can also be retrieved from this tab ...

ccaHCCPMemChanSwitchEntry

A set of attributes of the channel switch specifying the channel switch details per member (ccaHCCPMemberID) on an interface (ifType is docsCableMaclayer(127)) of a HCCP group.

ccaHCCPMemChanSwitchID

Uniquely identifies the entry for channel switch for a member. The channel switch is the RF component that allows downstream and upstream channel switching.

ccaHCCPMemChanSwitchType

Type of the channel switch. others(1) : Any other channel switch which is not in the following list. ucWavecom(2) : Represents the Wavecom upconvertor. rfSwitchGrp(3) : Weinschel channel switch. If ccaHCCPMemChanSwitchModule represents the ...

ccaHCCPMemChanSwitchIpAddrType

The type of internet address of ccaHCCPMemChanSwitchIpAddress.

ccaHCCPMemChanSwitchIpAddress

The Ipv4 Address of channel switch. It represents the IP address of the upconverter that this Working member connects to if ccaHCCPMemChanSwitchType is ucWavecom(2). It specifies the RF Switch's IP address if ccaHCCPMemChanSwitchType is rfSwitchGrp(3) or ...

ccaHCCPMemChanSwitchModule

The module number of channel switch for this member . It is the module number on the upconverter that this member connects to if ccaHCCPMemChanSwitchType is ucWavecom(2). It specifies the RF Switch module number inside an RF Switch chassis if ccaHCCPMemCh ...

ccaHCCPMemChanSwitchProtIpAddrType

The type of internet address of ccaHCCPMemChanSwitchProtIpAddr.

ccaHCCPMemChanSwitchProtIpAddr

The IP address of the Wavecom upconvertor that is connected to the corresponding Protect for this Working member. This object is meaningful only if ccaHCCPMemChanSwitchType is ucWavecom(2) and has no meaning for other types of switches and is ignored in t ...

ccaHCCPMemChanSwitchProtModule

The module number on the Wavecom upconvertor that is connected to the corresponding Protect for this Working member. This object is meaningful only if ccaHCCPMemChanSwitchType is ucWavecom(2).

ccaHCCPMemChanSwitchPosition

The position within a switch module for this Working member. This object is valid for ccaHCCPMemChanSwitchType rfSwitchGrp(3) and rfSwitchModule(4).

ccaHCCPMemChanSwitchSnmpEnable

This object is used to enable SNMP remote control on the Wavecom upconvertor. When it is set to true(1), SNMP remote control is enabled on the upconvertor. When it is set to false(2), SNMP remote control is disabled and front panel manual operation is ena ...

ccaHCCPOnOffNotificationEnable

An indication of whether the ccaHCCPOnNotification and ccaHCCPOffNotification are enabled or disabled.

ccaHCCPGroup

Group of objects implemented in CMTS providing HCCP group information.

ccaHCCPMemberGroup

Group of objects implemented in CMTS providing HCCP member and channel switch information.