CISCO-XDSL-LINE-MIB Download
The tables defined by this MIB module contain a collection
of managed objects that are general in nature and apply to
different types of modems. The structure of this module
resembles the ADSL-LINE-MIB, CISCO-SDSL-LINE-MIB,
ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, etc.
Observe that the tables in this module do not necessarily
extend the tables defined by the these mibs. Currently,
only the table that contains the configuration information
extends the profile tables defined by the above modules.
IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for CISCO-XDSL-LINE-MIB
- cXdslLineTable
- This table contains enterprise-specific line parameters for XTU-C class xDSL devices supported by the system.
- cXdslLineEntry
- A set of enterprise-specific xDSL line parameters for an XTU-C class device. There exists an entry for each ifEntry with an ifType of xDSL such as adsl, sdsl, idsl, etc. that are supported by the system.
- cXdslLineTimeSinceLastChange
- Represents the time elapsed since the status of this interface was last changed.
- cXdslLineNoOfChanges
- Represents the number of changes of the interface status since last reset of the agent or since a XTU-C modem was installed.
- cXdslTestTable
- This table contains enterprise-specific test parameters initiated by the XTU-C class devices supported by the system.
- cXdslTestEntry
- A set of enterprise-specific test parameters for an XTU-C class xDSL device. There exists an entry for each ifEntry with an ifType of xDSL such as adsl, sdsl, idsl, etc. that are supported by the system.
- cXdslTestStatus
- Represents status of the test per port. Once a test is completed or aborted, the status remains at passed, failed, or aborted until user clears it by setting cXdslTestTrigger to clear or starts a new test. This object will return 'passed' if there are no ...
- cXdslTestType
- The type of test to be performed. The test duration is determined by cXdslTestTime. All the test types inhibit the service on that line. The agent will only change cXdslTestType, if no test is active on the targeted port. The XTU-C may support other test ...
- cXdslTestTrigger
- Starts, stops (aborts) a test in progress or clears the test results. The agent will only start a new test, if no test is active on the targeted port. The value of this object returns 'ready' when read, the value cannot be set to 'ready'. The cXdslTestTri ...
- cXdslTestTime
- Test duration. Time interval between 1 - 30 minutes.
- cXdslTestBertErrors
- Errors during BERT test. The test will abort if any BERT errors occur. Note: that even if there are no BERT errors the test can still fail due to BertBitErrors. Bit Description --- ----------- 0 No BERT errors 1 XTU-R BERT aborted 2 XTU-R los ...
- cXdslTestBertBitErrors
- This value represents the number of BERT bit errors accumulated during the test duration, the value may not be available until completion of the test. The test will fail if this value is greater than 0.
- cXdslTestBertRunTime
- This value represents the BERT run time in seconds, the value may not be available until completion of the test.
- cXdslTestBertBitRate
- This value represents the BERT bitrate in bps that was detected during the BERT test, the value may not be available until completion of the test.
- cXdslModeTable
- This table contains enterprise-specific mode parameters initiated by the XTU-C class devices supported by the system.
- cXdslModeEntry
- A set of enterprise-specific mode parameters for an XTU-C class xDSL device. There exists an entry for each ifEntry with an ifType of xDSL such as adsl, sdsl, idsl, etc. that are supported by the system.
- cXdslModeLoopback
- The value of this object specifies the loopback mode of this interface. The interface will stay in loopback mode until this object is set to disabled. The XTU-C may support other mode types that are not defined in this mib, if such mode is running, this o ...
- cXdslModeSpectrum
- The value of this object specifies the spectrum mode of this interface. The interface will stay in spectrum mode until this object is set to disabled. The modes will inhibit the service on that line. Not all spectrum modes are avaiable for all types of mo ...
- cXdslLineConfProfileEntry
- A configuration profile containing enterprise-specific xDSL line configuration information. An entry exist in this table for every profile created by adslLineConfProfileRowStatus which will also modify or delete an existing row in this table.
- cXdslLineConfPayloadScrambled
- This object specifies whether ATM Payload Scrambling is enabled for this profile.
- cXdslLineConfAlarmsEnabled
- This object specifies whether Alarms are enabled for this profile.
- cXdslLineConfLinkUpDownTrap
- This object specifies whether Link Up/Down traps are enabled for this profile.
- cXdslLineGroup
- A collection of managed objects defining the enterprise- specific attributes of a xDSL line.
- cXdslLineConfProfileGroup
- A collection of managed objects defining the enterprise-specific line configuration information associated with one or more xDSL XTU-C class devices.
- cXdslTestGroup
- A collection of managed objects defining the enterprise-specific test options associated with one or more xDSL XTU-C class devices. Implemention of this group is optional.
- cXdslModeGroup
- A collection of managed objects defining the enterprise-specific line mode options associated with one or more xDSL XTU-C class devices. Implemention of this group is optional.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
