Nortel-Magellan-Passport-VnetMcdnSigMIB

Nortel-Magellan-Passport-VnetMcdnSigMIB Download

MIBs list

The module describing the Nortel Magellan Passport VnetMcdnSig Enterprise MIB.

IPHost Network Monitor offer an easy way of SNMP monitoring your Nortel network devices, Firewalls, Repeaters.

OID list for Nortel-Magellan-Passport-VnetMcdnSigMIB

sigChanMcdnRowStatusTable
This entry controls the addition and deletion of sigChanMcdn components.
sigChanMcdnRowStatusEntry
A single entry in the table represents a single sigChanMcdn component.
sigChanMcdnRowStatus
This variable is used as the basis for SNMP naming of sigChanMcdn components. These components can be added and deleted.
sigChanMcdnComponentName
This variable provides the component's string name for use with the ASCII Console Interface
sigChanMcdnStorageType
This variable represents the storage type value for the sigChanMcdn tables.
sigChanMcdnIndex
This variable represents the index for the sigChanMcdn tables.
sigChanMcdnL2Table
This group specifies the provisionable layer 2 attributes of the Q.931 ITU-T protocol.
sigChanMcdnL2Entry
An entry in the sigChanMcdnL2Table.
sigChanMcdnT23
This attribute specifies the layer 2 enable request timer.
sigChanMcdnT200
This attribute specifies the maximum time between a layer 2 frame and its acknowledgment.
sigChanMcdnN200
This attribute specifies the maximum number of re-transmissions of a layer 2 frame.
sigChanMcdnT203
This attribute specifies the maximum time for which layer 2 frames may be absent. Expiry triggers a check on whether the far end is alive.
sigChanMcdnCircuitSwitchedK
This attribute specifies the maximum number of sequentially numbered I frames (that is, window size (k)) that may be unacknowledged at any given time for a SAP supporting primary rate (64kbit/sec) signalling.
sigChanMcdnL3Table
This group represents the provisionable Layer 3 timer attributes of the MCDN signalling protocol.
sigChanMcdnL3Entry
An entry in the sigChanMcdnL3Table.
sigChanMcdnT302
This attribute specifies the overlap receiving timer; in a UNI, this is network to user, but for Peer to Peer it is all incoming calls. This attribute is ignored if overlap signalling is disabled.
sigChanMcdnT304
This attribute specifies the overlap sending timer; in a UNI, this is user to network, but for Peer to Peer it is all outgoing calls. This attribute is ignored if overlap signalling is disabled.
sigChanMcdnT309
This attribute specifies the data link disconnect timer; used to ride out temporary failures.
sigChanMcdnT310
This attribute specifies the call proceeding state timer.
sigChanMcdnT316
This attribute specifies the restart request response timer. It must be set greater than t317.
sigChanMcdnT317
This attribute specifies the restart operation timer, used when a RESTART was received.
sigChanMcdnProvTable
This group defines the general options of the D-channel signalling link.
sigChanMcdnProvEntry
An entry in the sigChanMcdnProvTable.
sigChanMcdnSide
This attribute specifies whether the interface provides layer 2 and 3 services equivalent to the ITU-T network or user side of the connection. If this attribute is set to network, then the interface is master during channel negotiation, and uses network s ...
sigChanMcdnMaxNonCallConcurrent
This attribute specifies the maximum number of simultaneous active non-call transactions that are allowed.
sigChanMcdnOverlapSending
This attribute specifies whether overlap sending to the PBX is enabled.
sigChanMcdnOverlapReceiving
This attribute specifies whether overlap receiving from the PBX is enabled.
sigChanMcdnChanMaintenanceHandling
This attribute specifies handling of channel maintenance events such as locking and unlocking a channel or channel registration on start-up. The decision here is whether to send individual channel RESTART messages, SERVICE messages, or nothing. Note that ...
sigChanMcdnStateTable
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...
sigChanMcdnStateEntry
An entry in the sigChanMcdnStateTable.
sigChanMcdnAdminState
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...
sigChanMcdnOperationalState
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...
sigChanMcdnUsageState
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...
sigChanMcdnStatsTable
This group provides the operational components for the McdnSig component.
sigChanMcdnStatsEntry
An entry in the sigChanMcdnStatsTable.
sigChanMcdnTotalCallsToIf
This attribute counts the total number of calls that have been made to the interface. The value wraps when it reaches its maximum.
sigChanMcdnTotalCallsFromIf
This attribute counts the total number of calls from the interface. The value wraps when it reaches its maximum.
sigChanMcdnNonCallAssocSessionsToIf
This attribute counts the total number of non-call associated sessions to the interface. The value wraps when it reaches its maximum.
sigChanMcdnNonCallAssocSessionsFromIf
This attribute counts the total number of non-call associated sessions from the interface. The value wraps when it reaches its maximum.
sigChanMcdnOperTable
This group provides the operational attributes for the MCDN signalling.
sigChanMcdnOperEntry
An entry in the sigChanMcdnOperTable.
sigChanMcdnActiveChannels
This attribute indicates the number of currently active channels. This includes data and voice channels.
sigChanMcdnActiveVoiceChannels
This attribute indicates the number of channels that are currently carrying voice.
sigChanMcdnActiveDataChannels
This attribute indicates the number of channels that are currently carrying data. This does not include modem data.
sigChanMcdnPeakActiveChannels
This attribute indicates the maximum number of channels that have been active on this signalling channel during the last polling period.
sigChanMcdnPeakActiveVoiceChannels
This attribute indicates the maximum number of voice channels that have been active on this signalling channel during the last polling period.
sigChanMcdnPeakActiveDataChannels
This attribute indicates the maximum number of data channels that have been active on this signalling channel during the last polling period.
sigChanMcdnDChanStatus
This attribute indicates the state of the D-channel. outOfService means that there is no layer 2 or layer 3 connectivity to the PBX. establishing means that the signalling channel is attempting to stage the layer 2. established means that the layer 2 is e ...
sigChanMcdnToolsTable
This contains a series of operational attributes which turn on and off several kinds of tracing.
sigChanMcdnToolsEntry
An entry in the sigChanMcdnToolsTable.
sigChanMcdnTracing
This attribute defines which types of tracing are active for this signalling channel. The tracing messages are sent to the debug stream. To see the messages the agentQueue attribute in Col/debug must be greater than 0 and a Telnet NMIS session must list ...
sigChanMcdnMessageTraced
This attribute specifies the type of ISDN messages that are to be traced. Description of bits: alerting(0) callProceeding(1) connectionlessFacility(2) congestionControl(3) connect(4) connectAcknowledge(5) disconnect(6) facility(7) facilityAcknowledge(8) f ...
sigChanMcdnDirectionTraced
This attribute indicates whether the incoming (from PBX), outgoing (to PBX), or both incoming and outgoing messages are traced. Description of bits: incoming(0) outgoing(1)
sigChanMcdnClsTable
This group enables and disables the support of the MCDN proprietary signalling for connectionless features on the local signalling channel.
sigChanMcdnClsEntry
An entry in the sigChanMcdnClsTable.
sigChanMcdnClsFeaturesSupported
This attribute specifies the features to be supported by MCDN 'TCAP' connectionless messaging. Note that some features such as Network ACD combine connectionless and connection oriented. In the NACD case, the connectionless messaging enables the source an ...
sigChanMcdnCoTable
This group enables and disables the support of the MCDN proprietary signalling for the listed features on the local signalling channel.
sigChanMcdnCoEntry
An entry in the sigChanMcdnCoTable.
sigChanMcdnDropBackCongestion
This attribute specifies if the Meridian 1 Drop Back Congestion Handling for trunks is enabled, and what type is being supported.
sigChanMcdnNetworkNameDisplay
This attribute specifies what Name Display is supported. nd1 corresponds to the Meridian 1 RCAP (Remote CAPability) nd1. This translates as caller provides name info in SETUP, ringing party name in ALERTING, redirection name in NOTIFY, and answering party ...
sigChanMcdnMultisiteBusinessGroup
This attribute specifies whether to enable transport for the Meridian 1 Multisite Business Group IE. The Meridian 1 allows multiple 'Tenants' to exist on a single PBX. These Tenants have limited access to each other and to system resources. That is, use ...
sigChanMcdnConOrFeaturesSupported
This attribute indicates the features to be supported by MCDN 'ROSE' connection oriented messaging. Feature Definitions: networkAttendantService: network wide support of Attendant ('operator') services. classOfServiceTransport: this is not a ROSE feature. ...
sigChanMcdnFramerRowStatusTable
This entry controls the addition and deletion of sigChanMcdnFramer components.
sigChanMcdnFramerRowStatusEntry
A single entry in the table represents a single sigChanMcdnFramer component.
sigChanMcdnFramerRowStatus
This variable is used as the basis for SNMP naming of sigChanMcdnFramer components. These components cannot be added nor deleted.
sigChanMcdnFramerComponentName
This variable provides the component's string name for use with the ASCII Console Interface
sigChanMcdnFramerStorageType
This variable represents the storage type value for the sigChanMcdnFramer tables.
sigChanMcdnFramerIndex
This variable represents the index for the sigChanMcdnFramer tables.
sigChanMcdnFramerProvTable
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
sigChanMcdnFramerProvEntry
An entry in the sigChanMcdnFramerProvTable.
sigChanMcdnFramerInterfaceName
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
sigChanMcdnFramerStateTable
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...
sigChanMcdnFramerStateEntry
An entry in the sigChanMcdnFramerStateTable.
sigChanMcdnFramerAdminState
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...
sigChanMcdnFramerOperationalState
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...
sigChanMcdnFramerUsageState
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...
sigChanMcdnFramerStatsTable
This group contains the operational statistics data for a Framer component.
sigChanMcdnFramerStatsEntry
An entry in the sigChanMcdnFramerStatsTable.
sigChanMcdnFramerFrmToIf
This attribute counts the number of frames transmitted to the link interface by Framer. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerFrmFromIf
This attribute counts the number of frames received from the link interface by Framer. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerOctetFromIf
This attribute counts the number of bytes received from the link interface by Framer. This count wraps to zero when it exceeds its maximum value.
sigChanMcdnFramerAborts
This attribute counts the total number of aborts received. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerCrcErrors
This attribute counts the total number of frames with CRC errors. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerLrcErrors
This attribute counts the total number of frames with LRC errors. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerNonOctetErrors
This attribute counts the total number of frames that were non octet aligned. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerOverruns
This attribute counts the total number of frames received from the link for which overruns occurred. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerUnderruns
This attribute counts the total number of frames transmitted to the link for which underruns occurred. This count wraps to zero after reaching its maximum value.
sigChanMcdnFramerLargeFrmErrors
This attribute counts the total number of frames received which were too large (longer than 500 bytes). This count wraps to zero after reaching its maximum value.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list