PoE-MIB

PoE-MIB Download

MIBs list

The Structure of PoE management for the proprietary enterprise.

IPHost Network Monitor offer an easy way of SNMP monitoring your D-Link Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for PoE-MIB

swPoESystemPowerLimit
The power budget (in watts) of the PoE sytem. The default setting is 370 W.
swPoESystemPowerDisconnectMethod
The power management disconnection method. When the total consumed power exceeds the power budget, the PoE controller initiates port disconnection, to prevent overloading the power supply. The controller uses one of the following two ways to implement the ...
swPoESystemManagementMode
This mode can be either power_limit mode or auto mode. power_limit: If power supplied to the port exceeds the power limit specified for it, this port will be shut down. auto: The system will automatically determine the PD class of the device connected to ...
swPoESystemLedMode
Specifies if the system mode will be POE or NORMAL.
swPoESystemStackingCtrlTable
A table that is used to configure PoE system information based on Unit ID. The Unit ID is used for stacking.
swPoESystemStackingCtrlEntry
A list of PoE system information based on Unit ID.
swPoESystemStackingCtrlUnitId
This object indicates the device's Unit ID. A unit ID of zero denotes a stand-alone device.
swPoESystemStackingCtrlPowerLimit
The power budget (in watts) of the PoE sytem. The default setting is 370 W.
swPoESystemStackingCtrlPowerDisconnectMethod
The power management disconnection method. When the total consumed power exceeds the power budget, the PoE controller initiates port disconnection to prevent overloading the power supply. The controller uses one of the following two ways to implement the ...
swPoESystemStackingCtrlManagementMode
This mode can be either power_limit mode or auto mode. power_limit: If power supplied to the port exceeds the power limit specified for it, this port will be shut down. auto: The system will automatically determine the PD class of the device connected to ...
swPoESystemStackingCtrlLedMode
Specifies the system mode to be POE or NORMAL.
swPoESystemStackingCtrlLegacyPD
The legacy PD detection state. Enables or disables legacy PD detection on PoE unit.
swPoESystemCtrlLegacyPD
The legacy PD detection state. Enables or disables legacy PD detection on all PoE port.
swPoESystemInfoTable
A table that contains PoE system information based on Unit ID. The Unit ID is used for stacking.
swPoESystemInfoEntry
A list of PoE system information based on Unit ID.
swPoESystemInfoUnitId
This object indicates the device's Unit ID. A unit ID of zero denotes a stand-alone device.
swPoESystemInfoPowerConsumption
The actual momentary power consumption (in watts) in the PoE system.
swPoESystemInfoPowerRemained
The actual momentary remaining power (in watts) in the PoE system.
swPoESystemInfoPowerLimit
The power budget (in watts) of the PoE sytem. The default setting is 370 W.
swPoESystemInfoPowerDisconnectMethod
The power management disconnection method. When the total consumed power exceeds the power budget, the PoE controller initiates port disconnection to prevent overloading the power supply. The controller uses one of the following two ways to implement the ...
swPoESystemInfoManagementMode
This mode can be either power_limit mode or auto mode. power_limit: If power supplied to the port exceeds the power limit specified for it, this port will be shut down. auto: The system will automatically determine the PD class of the device connected to ...
swPoESystemInfoLegacyPD
The current status of legacy PD detection.
swPoEPortCtrlTable
A table that contains PoE configuration about every port in this stack. If a device has N ports, then the 1 -- N ports describe the port number of BoxId 1 device; N+1 -- 2N describe the port number of BoxId 2 device; 2N+1 -- 3N describe the port number of ...
swPoEPortCtrlEntry
A list of PoE configurations for each port of the device in this stack.
swPoEPortCtrlPortIndex
This object indicates the devices' port number in this stack. If a device has N ports, then the 1 -- N ports describe the port number of BoxId 1 device; N+1 -- 2N describe the port number of BoxId 2 device; 2N+1 -- 3N describe the port number of BoxId 2 d ...
swPoEPortCtrlState
The PoE port state. Enables or disables the PoE function on the specific port. The default setting is enable.
swPoEPortCtrlPriority
The PoE port priority. Port priority affects power-up order (after a rest, the ports are powered up according to their priority) and shutdown order (when exceeding the power budget, the ports are shut down according to their priority if power_disconnect_m ...
swPoEPortCtrlPowerLimit
There are 4 pre-defined values for users' convenience to set the upper power limit for class 0, class 1, class 2, and class 3. class_0: 15400mW (The maximum power provided by PSE (switch) is 12.95 W + power loss on cable) class_1: 4000mW (The maximum powe ...
swPoEPortCtrlUserDefined
User defined per-port power limit (in milliwatts). If a port exceeds 10% of its power limit, the PoE system will shut down that port. The default setting is 15400 mW. Note: This object is valid only while the swPoEPortCtrlPowerLimit object is configured a ...
swPoEPortCtrlTimeRangeName
Specifies the time_range that applies to the port of the POE.If time range is configured, power can only be supplied during the period specified by the time range.
swPoEPortInfoTable
A table that contains PoE information about every port in this stack. If a device has N ports, then the 1 -- N ports describe the port number of BoxID 1 device; N+1 -- 2N describe the port number of BoxID 2 device; 2N+1 -- 3N describe the port number of B ...
swPoEPortInfoEntry
A list of PoE information for each port of the device in this stack.
swPoEPortInfoPortIndex
This object indicates the devices' port number in this stack. If a device has N ports, then the 1 -- N ports describe the port number of BoxId 1 device; N+1 -- 2N describe the port number of BoxID 2 device; 2N+1 -- 3N describe the port number of BoxID 2 d ...
swPoEPortInfoClass
The power class of the PD according to 802.3af definitions: class 0: PD power consumption is within 0.44-12.95 watts, class 1: PD power consumption is within 0.44-3.84 watts, class 2: PD power consumption is within 3.84-6.49 watts, class 3: PD power consu ...
swPoEPortInfoPower
The port power consumption (in milliwatts).
swPoEPortInfoVoltage
The port input line voltage (in decivolts).
swPoEPortInfoCurrent
The port current (calculated in milliamps).
swPoEPortInfoStatus
The string describes the PoE port current status.
swpoEPortInfoLedStatus
The LED display for PoE port status. on (1): power is provided to the port on which a 802.3af-compliant or legacy PD is connected, off(2): no power is provided to the port where there aren't any errors, error(3): some error happens on the port, like overl ...

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list