XYLAN-WSM-MIB Download

wsmPortTable

A table of port layer status and parameter information for the WSM's physical interfaces.

wsmPortEntry

An entry in the table, containing information about the physical layer of a WSM interface.

wsmPortSlotIndex

A unique value which identifies this HSM board slot.

wsmPortPortIndex

A unique value which identifies this WSM submodule port.

wsmPortInterfaceType

The type of interface on this WSM physical port.

wsmPortCableType

The type of cable attached to the universal serial port. Non Universal Serial Ports will always return 'unknown'. NOTE: RS-449 cables will return as RS-530 as they are detected as the same type. RS-449 is implemented only as a different connector (DB-37 ...

wsmPortSerialRxClockPol

The receive clock polarity. It is inverted or not inverted. For interfaces that do not support this, the value will be stored but ignored.

wsmPortSerialTxClockPol

The Transmit clock polarity. It is inverted or not inverted. For interfaces that do not support this, the value will be stored but ignored.

wsmPortFunctionType

The functional capability of the port. This allows the Manager code to determine the capabilities of the port so the proper data can be managed based on the functions the WAN port can provide. A 'frameType' port supports layer 2 protocols such as HDLC and ...

wsmPortProtocol

The layer 2 protocol of the port. This parameter only applies when wsmPortFunctionType is equal to frameType(1). For ports that don't support this (e.g. Circuit Emulation T1 ports) only a value of none(1) is supported. For ports that support upper layer p ...

wsmPortIfIndex

The ifIndex of the WAN port. This parameter is used in order to get the physical port Index used for SNMP standard MIBs that use ifIndex instead of slot/port.

wsmPortT1E1StartingTimeSlot

Starting TimeSlot for Fractional T1E1 board. This is only use for Fractional T1E1 board type. Valid Range: T1: 1..24 E1: 1..31 (May need to skip 16) The valid range may be effected by wsmPortT1E1NumberOfTimeSlot too.

wsmPortT1E1NumberOfTimeSlot

Number of TimeSlot for Fractional T1E1 board. This is only use for Fractional T1E1 board type. Valid Range: T1: 1..24 E1: 1..31 The valid range may be effected by wsmPortT1E1NumberOfTimeSlot too.

linkxTable

A table of WAN link(s) configuration information.

linkxEntry

An entry in the WAN link Configuration table, containing information about a single link's configuration.

linkxPeerID

The peer ID. This is used as a unique ID to identify a remote entity and to associate links to it. For example, for 'normal' PPP, there is one entry in the link table. For Multilink PPP there are one or more multiple links. In either case the Link tabl ...

linkxIfIndex

The ifIndex of the Link. This is used as a unique ID to identify an individual WAN link entity.

linkxDescription

A description for this WAN link.

linkxAdminStatus

This object controls the Administrative Status of this WAN Link Entity. Enabled will allow the Link Entity to operate. Disabled will disable the Link Entity without deleting it. Delete will disable the Link entity and delete the PPP configuration record ...

linkxType

The type of link. A wsmPort type is for WSM serial and Fractional T1 ports. An ISDN call is for incoming or outgoing ISDN calls. Additional information can then be found in Xylan and Standard MIBs based on the type of the link.

linkxSlot

The slot that is Link is on or zero if the link is not tied to a given slot (e.g. for ISDN incoming calls). If type is wsmPort(1), this must be a non-zero value.

linkxPort

The port that is Link is on or zero if the link is not tied to a given port (e.g. for ISDN incoming calls or Multilink PPP that requires to run Multilink with combined serial ports and ISDN calls on the same slot, but not necessarily fixed to a given ISDN ...

linkxMode

This object define whether the given link is to be a On-Demand Link or it is use for Backup.