CISCO-ADSL-CAP-LINE-MIB Download

cAdslAtucCapPhysTable

This table extends the adslAtucPhysTable and contains enterprise-specific physical layer parameters for the ATU-C class devices supported by the system.

cAdslAtucCapPhysEntry

A set of enterprise-specific physical-layer parameters for an ATU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of adsl(94) and an adslLineCoding of cap(3).

cAdslAtucCapCurrState

This object specifies the state of the ATU-C transceiver. The value of this managed is 'idle' for an ATU-C that has been provisioned, but is not physically present in the system.

cAdslAtucCapCurrRxGain

This managed object represents the gain applied to the ATU-C receiver. The value of this managed object is '0' for an ATU-C that has been provisioned, but is not physically present in the system.

cAdslAtucCapCurrRxSnr

This managed object represents the signal-to-noise ratio measured across the the ATU-C receive pair. The value of this managed object is '0' for an ATU-C that has been provisioned, but is not physically present in the system.

cAdslAturCapPhysTable

This table extends the adslAturPhysTable and contains enterprise-specific physical layer parameters for the ATU-R class devices supported by the system.

cAdslAturCapPhysEntry

A set of enterprise-specific physical-layer parameters for an ATU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of adsl(94) and an adslLineCoding of cap(3).

cAdslAturCapCurrRxGain

This managed object represents the gain applied to the ATU-R receiver. The value of this managed object is '0' if the corresponding ATU-C has been provisioned, but is not physically present in the system.

cAdslAtucCapPerfDataTable

This table extends the adslAtucPerfDataTable and contains enterprise-specific physical layer statistics for the ATU-C class devices supported by the system.

cAdslAtucCapPerfDataEntry

A set of enterprise-specific physical-layer statistics for an ATU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of adsl(94) and an adslLineCoding of cap(3).

cAdslAtucCapPerfInitFailures

This object specifies the number of line initialization failures relative to sysUpTime.

cAdslAtucCapPerfCurr15MinInitFailures

This object specifies the number of line initialization failures in the current 15-minute interval.

cAdslAtucCapPerfCurr1DayInitFailures

This object specifies the number of line initialization failures in the current 1-day interval.

cAdslAtucCapPerfPrev1DayInitFailures

This object specifies the number of line initialization failures in the previous 1-day interval.

cAdslAtucCapIntervalTable

This table extends the adslAtucIntervalTable and contains enterprise-specific physical layer statistics intervals for the ATU-C class devices supported by the system.

cAdslAtucCapIntervalEntry

A 15-minute interval of enterprise-specific physical-layer statistics for an ATU-C class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of adsl(94) and an adslLineCoding of cap(3).

cAdslAtucCapIntervalInitFailures

This object specifies the number of line initialization failures in the interval.

cAdslLineCapConfProfileTable

This table extends the adslLineConfProfileTable and contains enterprise-specific ADSL line configuration information.

cAdslLineCapConfProfileEntry

A configuration profile containing enterprise-specific ADSL line configuration information.

cAdslLineCapConfTrainingMode

This object specifies the mode employed by the ATU-C and ATU-R when training against each other. One of two training modes can be employed: - Standard An ATU-C initiates a training sequence using the method defined by T1E1.4/99-161R3. This training mode ...

cAdslLineCapConfInterleaveDelay

This object specifies the interleave delay for the downstream channel. The value of this object specifies the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver outp ...

cAdslLineCapConfCpeSignature

This object specifies the value of the minimum CPE signature expected from ATU-R during training. The value of the CPE signature corresponds to the software version of the ATU-R. If the CPE signature advertised by an ATU-R is less than the value of this ...

cAdslAtucCapConfTargetSnrMgn

This object specifies the target SNR margin. This is the desired noise margin the ATU-C must achieve with a BER of 10-7 or better to successfully complete training.

cAdslAtucCapConfMinTxRate

This object specifies the minimum acceptable downstream line rate.

cAdslAtucCapConfMaxTxRate

This object specifies the desired line rate which the ATU-C will attempt to train at.

cAdslAtucCapConfDown136KBaudEnable

This object specifies whether the modem can train the downstream channel using a symbol rate of 136K symbols per second.

cAdslAtucCapConfUp68KBaudEnable

This object specifies whether the modem can train the upstream channel using a symbol rate of 68K symbols per second. The value of this object does not effect whether the modem can train at any other symbol rate; that is, the values of this object and cAd ...

cAdslAtucCapConfUp17KBaudEnable

This object specifies whether the modem can train the upstream channel using a symbol rate of 17K symbols per second. The value of this object does not effect whether the modem can train at any other symbol rate; that is, the values of this object and cAd ...

cAdslAtucCapConfPsdmLevel

This managed object specifies the nominal power output of the ATU-C across the entire transmit spectrum. Observe that this implies the attenuation of the signal for some data rates. This value does not take effect until the modem has retrained against th ...

cAdslAturCapConfTargetSnrMgn

This object specifies the target SNR margin. This is the desired noise margin the ATU-R must achieve with a BER of 10-7 or better to successfully complete training.

cAdslAturCapConfMinTxRate

This object specifies the minimum acceptable upstream line rate.

cAdslAturCapConfMaxTxRate

This object specifies the desired line rate which the ATU-R will attempt to train at.

cAdslAturCapConfPsdmLevel

This managed object specifies the nominal power output of the ATU-R across the entire transmit spectrum. Observe that this implies the attenuation of the signal for some data rates. This value does not take effect until the modem has retrained against th ...

cAdslAtucCapBasicGroup

A collection of managed objects defining the basic operation of an ATU-C implementing the CAP line code.

cAdslAturBasicGroup

A collection of managed objects defining the basic operation of an ATU-R implementing the CAP line code.

cAdslAturCapGroup

A collection of managed objects defining the capability to remotely manage a ATU-R.

cAdslAtucCapPM15MinIntervalGroup

A collection of managed objects defining near-end performance data collection capability using 15-minute intervals.

cAdslAtucCapPM1DayIntervalGroup

A collection of managed objects defining near-end performance data collection capability using 1-day intervals.