CISCO-ADSL-DMT-LINE-MIB Download

cAdslDmtLineTable

This table extends the adslLineTable and contains enterprise- specific common attributes describing both ends of ADSL lines supported by the system.

cAdslDmtLineEntry

A set of enterprise-specific common attributes describing both ends of an ADSL line supported by the system. There exists an entry for each ifEntry with an ifType of adsl(94).

cAdslDmtLineOverheadFraming

This object represents the negotiated overhead framing structure being used by the ATU-C and ATU-R.

cAdslAtucDmtPhysTable

This table extends the adslAtucPhysTable and contains enterprise-specific physical layer parameters for ATU-C class devices supported by the system.

cAdslAtucDmtPhysEntry

A set of enterprise-specific physical-layer parameters for an ATU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of adsl(94).

cAdslAtucDmtState

The value of this object specifies the enterprise-specific specific status of the ATU-C. If the value of adslAtucDMTState is not 'other', then the value of this object is 'standard'. If the value of adslAtucDMTState is 'other', and the ATU-C is in an unr ...

cAdslAtucDmtChanTable

This table extends the adslAtucChanTable and contains enterprise-specific physical layer parameters for the ATU-C channels supported by the system.

cAdslAtucDmtChanEntry

A set of enterprise-specific physical-layer parameters for an ATU-C channel supported by the system. There exists an entry for each ifEntry with an ifType of adslInterleave(124) or adslFast(125).

cAdslAtucDmtChanFecSize

This object specifies the number of FEC redundancy bytes the ATU-C appends to downstream on the corresponding channel. The ATU-C can fallback from the initial value specified for the corresponding channel (i.e., cAdslAtucDmtConfFastFecSize or cAdslAtucIn ...

cAdslAtucDmtChanCodewordSize

This object specifies the actual number of symbols per codeword being used by the ATU-C for downstream messages. The ATU-C and ATU-R negotiate this value during the training sequence. A value of 0 indicates the automatic mode.

cAdslAturDmtChanTable

This table extends the adslAturChanTable and contains enterprise-specific physical layer parameters for the ATU-R channels supported by the system.

cAdslAturDmtChanEntry

A set of enterprise-specific physical-layer parameters for an ATU-R channel supported by the system. There exists an entry for each ifEntry with an ifType of adslInterleave(124) or adslFast(125).

cAdslAturDmtChanFecSize

This object specifies the number of FEC redundancy bytes the ATU-R appends to upstream on the corresponding channel. The ATU-C can fallback from the initial value specified for the corresponding channel (i.e., cAdslAturDmtConfFastFecSize or cAdslAturInte ...

cAdslAturDmtChanCodewordSize

This object specifies the actual number of symbols per codeword being used by the ATU-R for upstream messages. The ATU-C and ATU-R negotiate this value during the training sequence.

cAdslDmtLineConfProfileTable

This table extends the adslLineConfProfileTable and contains enterprise-specific ADSL DMT line configuration information.

cAdslDmtLineConfProfileEntry

A configuration profile containing enterprise-specific ADSL DMT line configuration information.

cAdslLineDmtConfOperatingMode

This object specifies the line operating mode being employed by the ADSL line. An ADSL line uses of one of two operating modes: - Automatic An ATU-C that employs this operating mode automatically detects the capabilities of the ATU-R and utilizes either ...

cAdslLineDmtConfTrainingMode

This object specifies the mode employed by the ATU-C and ATU-R when training against each other. One of two training modes can be employed: - Standard An ATU-C initiates a training sequence using the method defined by G.992.1, G.992.2, or T1.413-1998. T ...

cAdslAtucDmtConfFastFecSize

This object specifies the initial number of FEC redundancy bytes the ATU-C appends to downstream frames transmitted over the fast channel during the training sequence. The ATU-C can fallback from this value depending on the aggregate data rate achieved d ...

cAdslAtucDmtConfInterleaveFecSize

This object specifies the initial number of FEC redundancy bytes the ATU-C appends to downstream frames transmitted over the interleaved channel during the training sequence. The ATU-C can fallback from this value depending on the aggregate data rate ach ...

cAdslAtucDmtConfCodewordSize

This object specifies the number of symbols per codeword being used by the ATU-C for downstream messages on an interleaved channel during the training sequence. The ATU-C can fallback from this value based on the aggregate data rate achieved during train ...

cAdslAtucDmtConfOverheadFraming

This object specifies the overhead framing structure which the ATU-C will request when establishing a link with the ATU-R. The value of 'structure0' is not valid.

cAdslAtucDmtConfBitSwapEnabled

This object specifies whether the ATU-C performs bitswapping. Bitswapping attempts to maintain an acceptable margin for each bin; equalizing the margin across all bins through bit reallocation, thereby maximizing error performance. The ATU-C performs bits ...

cAdslAtucDmtConfBitSwapFrom

Bitswapping attempts to maintain an acceptable margin for each bin; equalizing the margin across all bins through bit reallocation, thereby maximizing error performance. The ATU-C performs bitswapping by monitoring the margin measured for each bin by the ...

cAdslAtucDmtConfBitSwapTo

Bitswapping attempts to maintain an acceptable margin for each bin; equalizing the margin across all bins through bit reallocation, thereby maximizing error performance. The ATU-C performs bitswapping by monitoring the margin measured for each bin by the ...

cAdslAturDmtConfFastFecSize

This object specifies the initial number of FEC redundancy bytes the ATU-R appends to upstream frames transmitted over the fast channel during the training sequence. The ATU-C can force the ATU-R to fallback from this value depending on the aggregate dat ...

cAdslAturDmtConfInterleaveFecSize

This object specifies the initial number of FEC redundancy bytes the ATU-R appends to upstream frames transmitted over the interleaved channel during the training sequence. The ATU-C can force the ATU-R to fallback from this value depending on the aggreg ...

cAdslAturDmtConfCodewordSize

This object specifies the number of symbols per codeword being used by the ATU-R for upstream messages on an interleaved channel during the training sequence. The ATU-C can force the ATU-R to fallback from this value based on the aggregate data rate achi ...

cAdslAtucDmtConfMinrateBlock

This object is used to implement min-rate blocking on DMT interfaces that support this option.

cAdslAtucDmtDualBitmapEnabled

This object is used to implement dual bitmap tables for Annex C compliant DMT interfaces. The bin data for the DSL interface will appear in cAdslAturDmtBinTable and cAdslAtucDmtBinTable.

cAdslDmtLineAlarmConfProfileTable

This table extends the adslLineAlarmConfProfileTable and contains enterprise-specific ADSL line configuration information pertaining to alarms.

cAdslDmtLineAlarmConfProfileEntry

A configuration profile containing enterprise-specific ADSL line configuration information pertaining to alarms

cAdslAtucDmtThreshRateFallback

This object specifies a bit rate threshold. When the following condition is met, the agent generates an adslAtucRateChangeTrap: ( I + F ) < cAdslAtucDmtThreshRateFallback where I = adslAtucChanCurrTxRate for ATU-C's interleave channel F = adslAtucChanCur ...

cAdslAturDmtThreshRateFallback

This object specifies a bit rate threshold. When the following condition is met, the agent generate an adslAturRateChangeTrap: ( I + F ) < cAdslAturDmtThreshRatefallback where I = adslAturChanCurrTxRate for ATU-R's interleave channel F = adslAturChanCurr ...

cAdslDmtBinIfNumber

The cAdslDmtBinIfNumber is used to set the ifIndex for for which DMT bin information will be collected in cAdslAtucDmtBinTable and cAdslAturDmtBinTable. The request will be processed when cAdslDmtIfRqstStatus is set to pollNow (1). Setting this object wil ...

cAdslDmtBinIfRqstStatus

This object initiates the polling and stores the status of the last DMT Bin request. This object can have the following values : reset (-1) : write this value to reset the the finite state machine (FSM) that controls the reading of bin information on ...

cAdslDmtBinIfLstRqstUpldTime

cAdslDmtBinIfLstRqstUpldTime stores the time and date when the last successful upload request was done. This field is used to determine the age of DMT Bin data in the cAdslAtucDmtBinTable and cAdslAturDmtBinTable.

cAdslAtucDmtBinTable

This table contains information on the 256 DMT bins in the downstream direction. Bins correspond to 4 kHz slots on a trained DSL line modem. The information stored in each bin includes bit counts per hertz of bandwidth and the transmitter gain in 0.01 dB ...

cAdslAtucDmtBinEntry

A set of enterprise-specific parameters for a DMT DSL interface. After bin data has been collected successfully there will be at least 1 row entry for the interface indicated by cAdslAtucDmtBinIfIndex.

cAdslAtucDmtBitmapIndex

This index is used to step through all of the bin tables on a DSL interface.

cAdslAtucDmtBinIndex

A unique value, greater than zero, for each dmt bin on the interface specified in cAdslDmtBinIfNumber It is recommended that values be assigned contiguously starting from 1.

cAdslAtucDmtBinBitAlloc

This stores the number of bits allotted per Hertz in this bin. For example, a value of 15 would indicate that this slot is tranmitting at a physical rate of 64kbits/sec.

cAdslAtucDmtBinTxGain

This field has the transmitter gain for this bin and is stored in 0.01 dB increments.

cAdslAtucDmtBinNumber

This field indicates the 4.3125 kHz band of downstream DSL line spectrum occupied by a bin. For example, a value of 3 would indicate the band from 12.9375 to 17.25 kHz of the spectrum.

cAdslAturDmtBinTable

This table contains information for the 32 DMT bins in the upstream direction. A bin corresponds to a 4 kHz slots on a trained DSL line modem. The information stored in each bin includes bit counts per hertz and the transmitter gain in 0.01 dB increments.

cAdslAturDmtBinEntry

A set of enterprise-specific parameters for a DMT DSL interface. After bin data has been collected successfully there will be at least 1 row entry for the interface indicated by cAdslAtucDmtBinIfIndex.

cAdslAturDmtBitmapIndex

This index is used to step through all of the bin tables on a DSL interface.

cAdslAturDmtBinIndex

A unique value, greater than zero, for each dmt bin on the interface specified in cAdslDmtBinIfNumber It is recommended that values be assigned contiguously starting from 1.

cAdslAturDmtBinBitAlloc

This stores the number of bits allotted per Hertz in this bin. For example, a value of 15 indicates that this slot is transmitting at a physical rate of 64 Kbits.

cAdslAturDmtBinTxGain

This field has the transmitter gain for this bin and is stored in 0.01 dB increments.

cAdslAturDmtBinNumber

This field indicates the 4.3125 kHz band of upstream DSL line spectrum occupied by a bin. For example, a value of 3 would indicate the band from 12.9375 to 17.25 kHz of the spectrum.

cAdslDmtLineGroup

A collection of managed objects defining the enterprise-specific attributes of an ADSL line supporting modems using the DMT line code.

cAdslAtucDmtPhysGroup

A collection of managed objects defining the enterprise-specific physical-layer parameters of an ATU-C using the DMT line code.

cAdslAtucDmtChanGroup

A collection of managed objects defining the enterprise-specific channel parameters of an ATU-C using the DMT line code.

cAdslAturDmtChanGroup

A collection of managed objects defining the enterprise-specific channel parameters of an ATU-R using the DMT line code.

cAdslDmtLineConfProfileGroup

A collection of managed objects defining the enterprise-specific line configuration information associated with one or more ADSL ATU class devices implementing the DMT line code. Replaced by cAdslDmtLineConfProfileGroupRev1.

cAdslDmtLineAlarmConfProfileGroup

A collection of managed objects defining the enterprise-specific line alarm configuration information associated with one or more ATU class devices implementing the DMT line code.

cAdslDmtBinIfGroup

A collection of managed objects defining the enterprise-specific line interface information used to collect bin data from DMT interfaces.

cAdslAtucDmtBinDataGroup

A collection of managed objects defining the enterprise-specific line BIN information associated with one or more ATUC class devices implementing the DMT line code.

cAdslAturDmtBinDataGroup

A collection of managed objects defining the enterprise-specific line BIN information associated with a ATUR class device implementing the DMT line code.

cAdslDmtLineConfProfileGroupRev1

A collection of managed objects defining the enterprise-specific line configuration information associated with one or more ADSL ATU class devices implementing the DMT line code.