CISCO-CNO-SWITCH-MIB Download
MIB specific to Cisco Network Office switches.
IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for CISCO-CNO-SWITCH-MIB
- cnosSysInfoSerialNo
- Serial number of the hardware.
- cnosSysInfoBoardRevision
- Returns the revision number of the switch main board on which the system firmware resides.
- cnosSysInfoBootVersion
- Returns the version number of the switch boot S/W residing in flash. The format is 'V1.2.3'.
- cnosSysInfoAddrCapacity
- The system-wide maximum number of addresses supported.
- cnosSysConfigReset
- Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). Setting this object to noReset(1) has no effect. The switch always returns the value noReset(1) when this object is read ...
- cnosSysConfigDefaultReset
- Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parameters will revert to their factory default settings, and all addresses assigned will be removed. ...
- cnosSysConfigMonitor
- Selects whether frames to/from certain ports are sent to conSwitchSysConfigMonitorPort. A port is selected for monitoring purpose when its cnosPortMonitoring object is set to enabled.
- cnosSysConfigMonitorPort
- Port number to which all frames to/from monitored ports are sent. Frames are only monitored if the sysConfigMonitor object is set to enabled(1). A number from 1 to 8 selects a switch port. The number 0 selects no monitor port.
- cnosPortTable
- A list of configuration entries for individually switched ports. There in one entry created automatically for each switch port (ifType of ethernetCsmacd) on the device.
- cnosPortEntry
- Configuration parameters for an individually switched port.
- cnosPortControllerRevision
- Returns the revision number of the port controller.
- cnosPortName
- A descriptive string of up to 80 characters used by the network administrator to name a port.
- cnosPortDuplexAdmin
- Set to fullDuplex(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfDuplex(2) to operate in normal mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other ...
- cnosPortDuplexStatus
- The operating duplex mode of the switched port.
- cnosPortSpeedAdmin
- Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to negotiate with the other end of the connection.
- cnosPortSpeedStatus
- The operating speed of the switched port.
- cnosPortMonitoring
- Set to enabled(1) to forward receive and transmit frames on this port to the port identified by cnosSysConfigMonitorPort. Set to disabled(2) to not monitor frame traffic on this port.
- cnosPortLinkStatus
- The current port link status.
- cnosPortSTPPortFastMode
- This object configures the port into the Spanning Tree port-fast mode. When enabled(1), the STP can transition the port's state directly from blocking to forwarding, and vice versa, without going through the intermediate listening and learning states. Thi ...
- cnosPortVlanMember
- Set the port to be a member of a specified VLAN. Set the port to all(5) to be shared among all VLANs.
- cnosVlanTable
- Table containing a list of VLANs.
- cnosVlanEntry
- Information pertaining to a VLAN.
- cnosVlanIndex
- Identification of a VLAN entry.
- cnosVlanSTPState
- The switch implements the 802.1d Spanning Tree Algorithm & Protocol (STP) on all its port to detect loops in the bridge topology. The user may, for any reason, elect to disable the execution of STP, by setting this object to disabled(2).
- ciscoCNOSwitchSysInfoGroup
- A collection of the system information objects for use with the Cisco CNO switch products.
- ciscoCNOSwitchConfigGroup
- A collection of the system configuration objects for use with the Cisco CNO switch products.
- ciscoCNOSwitchPortGroup
- A collection of the the switched port objects for use with the Cisco CNO switch products.
- ciscoCNOSwitchMonitorPortGroup
- A collection of the switched port monitoring objects for use with the Cisco CNO switch products.
- ciscoCNOSwitchVlanGroup
- A collection of the VLAN objects for use with the Cisco CNO switch products.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
