CISCO-LWAPP-CCX-RM-MIB Download

clcrdot11aBeaconEnabled

When set to 'true', LWAPP APs broadcast radio measurement request messages that include a beacon measurement request information element on 802.11a radio to clients compatible to CCX versions 2 and above. This configuration takes higher precedence than t ...

clcrdot11aBeaconInterval

The interval in hundredths of a second, in which the AP issues radio measurement request message to client periodically for every SSID. This configuration takes higher precedence than that on the radio interface of the particular AP when clcrAPIfOverrideG ...

clcrdot11bBeaconEnabled

When set to 'true', LWAPP APs broadcast radio measurement request messages that include a beacon measurement request information element, on 802.11b/802.11g radio to clients compatible to CCX versions 2 and above. This configuration takes higher preceden ...

clcrdot11bBeaconInterval

The interval in hundredths of a second, at which the AP issues radio measurement request message to client periodically for every SSID. This configuration takes higher precedence than that on the radio interface of the particular AP when clcrAPIfOverrideG ...

clcrAPIfTable

This table represents the CCX related parameters on the radio interface of the APs. The values configured through the objects of this table are passed onto the AP by the controller, when the AP joins the controller. There exists a row in this table for e ...

clcrAPIfEntry

Each entry represents a conceptual row in this table. An entry corresponding to each dot11 interface of an AP is added to this table when the AP joins the controller and deleted when AP disassociates from the controller.

clcrAPIfOverrideGlobal

If this object is set to 'true', values populated through clcrAPIfBeaconEnabled and clcrAPIfBeaconInterval are considered for sending beacon measurement requests. If this object is set to 'false', the values configured through the objects clcrdot11bBeacon ...

clcrAPIfBeaconEnabled

When set to 'true', LWAPP APs broadcast radio measurement request messages that include a beacon measurement request information element to clients compatible with CCX versions 2 and above. Global configuration at network level takes higher precedence if ...

clcrAPIfBeaconInterval

The interval at which the AP sends radio measurement request messages to the clients associated through each and every SSID.

clcrClientBeaconReportTable

This table reports the received signal power as seen by a wireless client when conducting radio measurements. Clients measure the received signal power by observing the beacon requests and probe response messages on all the specified channels and pass th ...

clcrClientBeaconReportEntry

Each entry represents a conceptual row in this table and populates the received signal power as observed and reported by the respective client.

clcrClientMacAddress

This object identifies the MAC address of a client that has sent a beacon report to the AP.

clcrClientRxPowerSignal

This object represents the signal strength of the beacon or probe response frame as seen by the client.

clcrClientTimeStamp

This object represents the value of sysUpTime at which the beacon measurement report was received.

clcrWlanTable

This table represents the CCX parameters of a particular WLAN. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable.

clcrWlanEntry

Each entry represents a conceptual row in this table and provides information about the CCX capabilities of the WLAN.

clcrVersionIESupport

This object indicates the support for the Cisco Compatible Extensions Version information element on this WLAN. A value of 'true' indicates the presence of the support and 'false' indicates the absence of the same.

clcrAironetIESupport

This object indicates the support for the Cisco Compatible Extensions Aironet information element on this WLAN. The support is enabled or disabled by setting this object to 'true' or 'false' respectively.

ciscoLwappCcxRmDot11aConfigGroup

This collection of objects represent the beacon request and beacon interval parameters for 802.11a networks.

ciscoLwappCcxRmDot11bConfigGroup

This collection of objects represent the beacon request and beacon interval parameters for 802.11a networks.

ciscoLwappCcxRmApIfConfigGroup

This collection of objects represent the beacon request and beacon interval parameters for the respective 802.11 radio interfaces.

ciscoLwappCcxRmBeaconReportGroup

This collection of objects represent information about the beacon reports received from CCX clients.

ciscoLwappCcxRmD11WlanConfigGroup

This collection of objects represent the CCX settings on a particular WLAN.