CISCO-MGX82XX-RPM-CONN-MIB Download

rpmChanGrpTable

This table contains endpoint configuration information for connections applicable to RPM service module.

rpmChanGrpEntry

An entry for logical channel. Each entry corresponds to a connection endpoint identified by Slot number and channel number.

rpmChanSlotNum

Specifies the slot number of the RPM card.

rpmChanInterface

This is the RPM's backplane interface. Currently there is only one interface.

rpmChanNum

This object identifies the channel number. This is also called Logical Connection Number(LCN). This is a unique number which identifies a connection. The LCN maps VPI and VCI. For VCC, VCI range is 1..3825, and LCN range is 16..3840. LCN = VCI + 16. For V ...

rpmChanRowStatus

This indicates the status of this channel. add(1) : Channel is added. del(2) : channel is deleted. mod(3) : Set to this value before modifying objects related to connection endpoints.

rpmChanVcd

Virtual Circuit Descriptor. A unique number which identifies a connection.

rpmChanVpi

The VPI value for this channel. For VPC, VPI range is 1..255 and LCN range is 3841..4095. LCN = VPI + 3840

rpmChanVci

The VCI value for this channel. For VCC, VCI range is 1..3825, and LCN range is 16..3840. LCN = VCI + 16.

rpmChanSubInterface

This is the RPM's backplane sub-interface.

rpmChanLocalVpi

This VPI together with the local VCI and NSAP represents the local end point in this connection. The VPI value is zero for rpmChanConnType value of vcc(2).

rpmChanLocalVci

This VCI together with the local VPI and NSAP represents the local end point in this connection.

rpmChanLocalNsap

This object identifies the local NSAP address. The bytes are mapped as follows: prefix : 13 bytes Cisco ID : 2 bytes Reserved : 2 bytes Slot/Port : 2 bytes[5 bit slot, 11 bits port] Selector : 1 byte. Of the 13 bytes for the node name, only the firs ...

rpmChanRemoteVpi

This VPI together with the remote VCI and NSAP represents the remote end point in this connection.

rpmChanRemoteVci

This VCI together with the remote VPI and NSAP represents the remote end point in this connection.

rpmChanRemoteNsap

This object identifies the remote NSAP address. The bytes are mapped as follows: prefix : 13 bytes Cisco ID : 2 bytes Reserved : 2 bytes Slot/Port : 2 bytes[5 bit slot, 11 bits port] Selector : 1 byte.

rpmChanType

This object identifies the channel type svc(1) : Switched Virtual Connection pvc(2) : Permanent Virtual Connection spvc(3) : Soft PVC.

rpmChanConnType

This specifies the connection type vpc(1) : Virtual Path Connection vcc(1) : Virtual Channel Connection

rpmChanServiceType

This object identifies the connection service type. cbr (1) : Constant Bit Rate vbr (2) : Variable Bit Rate ubr (4) : Unspecified Bit Rate atfr (5) : ATM Frame Relay abrstd (6) : Standard ABR abrfst (7) : foresight ABR.

rpmChanMastership

This specifies which end of the connection is the master. This is used by PXM to determine if this end point is master or slave.

rpmChanRtePriority

This is also known as class of service, it is used by PXM to determine how important this connection is when selecting connections to route.

rpmChanMaxCost

Maximum allowed cost. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level.

rpmChanRestrictTrkType

Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satellite trunks or terrestrial trunks, or it can be on any type of trunk.

rpmChanPCR

Peak cell rate.(in cells per sec.)

rpmChanRemotePCR

Peak cell rate of the remote endpoint of the connection. If not set, its value will be same as the value of rpmChanPCR.

rpmChanMCR

Minimum cell rate.(in cells per sec.).

rpmChanRemoteMCR

Minimum cell rate of the remote endpoint. If this is not set, its value will be same as value of rpmChanMCR.

rpmChanPercentUtil

This is the expected long-term utilization of the channel by this end-point.

rpmChanRemotePercentUtil

This is the expected long-term utilization of the channel by the other end-point. If this is not specified in the connection setup request, it'll be set to be the same as the local end.

rpmChanEncapType

This object identifies the ATM adaptation layer (AAL) and Encapsulation type. aal5snap - LLC/SNAP precedes the protocol datagram. aal34smds - Encapsulation for SMDS network. aal5nlpid - Encapsulation that allows ATM interfaces to interoperate with HSSI. ...

rpmChanMidLow

Starting Message Identifier Number for this PVC.

rpmChanMidHigh

Ending Message Identifier Number for this PVC.

rpmChanBurstSize

The Maximum number of ATM cells the virtual circuit can transmit.

rpmChanInArpFreq

Specifies how often Inverse ARP datagrams will be sent on this virtual circuit. The value zero will disable the IN-ARP for this channel. This object is supported only for the value of rpmChanEncapType = aal5snap.

rpmChanOAMloopback

This object specifies how often to generate an OAM F5 loopback cell from this virtual circuit. The value zero will disable generation of OAM F5 loopback cells.

rpmChanState

This indicates the status of this channel. 1 ==> notConfigured 2 ==> active 3 ==> failed. Currently 'failed' state is not supported. When the channel is not added, the state is notConfigured.

rpmChanVirtualTemplate

Specifies the Virtual Template used for CISCO PPP. If it is not using Virtual Template then this value is zero.

rpmChanAbrRDF

This is valid only for ABR Service Type. Rate Decrease Factor: Controls the rate decrease which occurs when backward RM-cells with CI=1 are received. Larger values lead to faster rate decrease.

rpmChanAbrRIF

This is valid only for ABR Service Type. Rate Increase Factor: Controls the rate increase which occurs when a backward RM-cell is received with CI=0 and NI=0. Larger values lead to faster rate increase.

cmrConnConfGroup

The objects related to Connections on RPM card.