CISCO-RMON-CONFIG-MIB Download

MIBs list

This module defines configuration extensions for some of the IETF RMON MIBs. The following terms are used throughout this MIB: A SPAN session is an association of one or more destination(s) with a set of source(s), along with other parameters, to specify the network traffic to be monitored. Each SPAN session is denoted by an unique number. The term 'remote SPAN', also called 'RSPAN', refers to the analysis of network traffic remotely, from destination port(s) for one or more source ports, distributed in one or more switches in a switched network, through a RSPAN VLAN.

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for CISCO-RMON-CONFIG-MIB

rmonTimeFilterMode: This object controls the way the SNMP agent implements the getnext operation for tables with a TimeFilter index, such as those found in the RMON2-MIB module. If this object has the value `stopAfterOne(1)', then a GetNext or GetBulk operation will provide ...
portCopyXTable: This table extends the port copy capability found in the SMON MIB portCopyTable. This table is intended to augment every portCopyEntry, but not all features provided may be available on all RMON platforms. In such a case, a particular MIB object will be i ...
portCopyXEntry: Describes a particular port copy extension entry. When creating an entry in this table using the 'createAndwait' method, the following rules are applied: - no SPAN consistency check is done for the entry until the entry is activated. An entry will not be ...
portCopyLoVlanMask: This object affects the way VLAN-based traffic is copied from a switch source port, for the indicated port copy operation. It is used in tandem with the portCopyHiVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used to se ...
portCopyHiVlanMask: This object affects the way VLAN-based traffic is copied from a switch source port, for the indicated port copy operation. It is used in tandem with the portCopyLoVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used to se ...
portCopyDestLoVlanMask: This object affects the way VLAN-based traffic to a switch destination port is filtered for the indicated port copy operation. It is used in tandem with the portCopyDestHiVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is us ...
portCopyDestHiVlanMask: This object affects the way VLAN-based traffic to a switch destination port is filtered for the indicated port copy operation. It is used in tandem with the portCopyDestLoVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is us ...
portCopyOption: Indicates the additional SPAN configuration on destination port. Instances of same portCopyDest index must have same values in portCopyOption. Changes on portCopyOption of one instance will be applied to all other instances of same portCopyDest index. - i ...
portCopySessionNo: Indicates the arbitrary unique identifier for this SPAN session. If a non zero value is specified, the agent will check if a SPAN session that has the same session number exists. If so, the agent will use this session number when this entry is activated. ...
portCopySessionType: Indicates the SPAN session type. 'remoteSource' refers to session where traffic is copied from source port to RSPAN VLAN as its destination port. 'remoteDestination' refers to session where traffic is copied from RSPAN VLAN to the destination port. For 'l ...
portCopyRemoveSrc: Indicates how the agent will modify a SPAN session when an entry belonging to this session is deleted. The value 'true' specifies source port based entry deletion. In source port based deletion, all entries of same index portCopySource from the session ar ...
portCopyReflectorPort: Indicates the reflector port of this SPAN session. The value of this object is ignored whenever the value of portCopySessionType is not remoteSource(3).
portCopyInpktVlan: This object indicates the default VLAN that is used for the untagged incoming traffic from the portCopyDest when portCopyOption's inpkts bit is set. The range is defined to identify all possible 4096 IEEE 802.1Q VLAN ID values although only 1 - 4094 are ...
portCopyMaxIngressSessions: The maximum number of local ingress (rx or both) SPAN session that can be configured on this agent.
portCopyMaxEgressSessions: The maximum number of local egress SPAN sessions that can be configured on this agent.
crcSpanSessionTable: Contains SPAN session entries. A row is created for each SPAN session configured in a device.
crcSpanSessionEntry: Describes a particular SPAN session.
crcSpanSessionNo: Defines a SPAN session number.
crcSpanSessionType: Defines the SPAN session type. 'local' refers to SPAN session where both source and destination ports reside in the same switch. This type of SPAN is manageable via portCopyTable and portCopyXTable. 'remote' refers to session where traffic is copied from ...
crcSpanSessionEnabled: Indicates whether the SPAN session is enabled. Modifying the value of crcSpanSessionEnabled to 'false' stops the SPAN monitoring but does not remove this SPAN configuration from the system.
crcSpanSessionDescr: Provides description of this SPAN session.
crcERSpanSessionTable: Contains ERSPAN session entries. A row is created for each SPAN session configured in a device. A row can only be created if an instance of the same session number is not present in crcSpanSessionEntry. ERSPAN, or Encapsulated Remote SPAN, provides the ...
crcERSpanSessionEntry: Describes a particular SPAN session.
crcERSpanSessionNo: Defines an ERSPAN session number.
crcERSpanSessionType: Defines the ERSPAN session type. This object may not be modified if the value of the corresponding instance of crcERSpanSessionRowStatus is active. 'eRSpanSource' refers to a session where traffic is copied from crcERSpanIFIndex of crcERSpanIFTable as sou ...
crcERSpanSessionDescr: Provides description of this ERSPAN session. This object may be modified when the row is active.
crcERSpanEncapID: Defines ERSPAN's encapsulation id for this entry. This object may be modified when the row is active.
crcERSpanIpType: Defines the type of Internet address for crcERSpanIp used by this entry. This object may be modified when the row is active.
crcERSpanIp: Defines Internet address of copy source or destination. If crcERSanSessionType has value of eRSpanSource(1), crcERSpanIp is a copy destination. If crcERSpanSessionType has value of eRSpanDestination(2), crcERSpanIp is a copy source. This object may be mod ...
crcSrcERSpanIpTTL: The IP TTL value for this traffic type. This object is only significant when object crcERSpanSessionType is eRSpanSource(1). This object may be modified when the row is active.
crcSrcERSpanDscpOrPrec: The QOS classification used - precedence or DSCP based. This object is only significant when object crcERSpanSessionType is eRSpanSource(1). This object may be modified when the row is active.
crcSrcERSpanIpPrec: The IP precedence value for this traffic type. This object is only significant when object crcERSpanSessionType is eRSpanSource(1) and object crcSrcERSpanDscpOrPrec is precedence(1). This object may be modified when the row is active.
crcSrcERSpanIpDscp: The IP DSCP value for this traffic type. This object is only significant when object crcERSpanSessionType is eRSpanSource(1) and object crcSrcERSpanDscpOrPrec is dscp(1). This object may be modified when the row is active.
crcERSpanIpVRF: Specifies VRF used for the traffic type. This object may be modified when the row is active.
crcSrcERSpanLoVlanMask: This object affects the way VLAN-based traffic is copied from a switch source port, for the indicated port copy operation. It is used in tandem with the crcSrcERSpanHiVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used t ...
crcSrcERSpanHiVlanMask: This object affects the way VLAN-based traffic is copied from a switch source port, for the indicated port copy operation. It is used in tandem with the crcSrcERSpanLoVlanMask to identify all possible 4096 IEEE 802.1Q VLAN ID values. This object is used t ...
crcSrcERSpanOrigIpType: Defines the type of Internet address for crcSrcERSpanOrigIp used by this entry. This object is only significant when object crcERSpanSessionType is eRSpanSource(1). This object may be modified when the row is active.
crcSrcERSpanOrigIp: Defines the Internet address of copy source. This object is only significant when object crcERSpanSessionType is eRSpanSource(1). This object may be modified when the row is active.
crcDstERSpanOption: Indicates the additional ERSPAN configuration on destination port. - inpkts(0) This bit is set to enable the destination port to receive incoming traffic. - learningDisable(1) This bit is set to suppress MAC learning for incoming traffic at the destinatio ...
crcERSpanSessionRowStatus: Defines the status of this entry.
crcERSpanIFTable: This table in conjunction with crcERSpanSessionTable, provides the ability to copy all frames from a specified source to a specified destination across a layer 3 network. A row is created for each interface from ifEntries that is configured as ERSPAN sour ...
crcERSpanIFEntry: Describes a particular ERSPAN copy source or copy destination entry.
crcERSpanIFIndex: Defines the device interface's ifIndex. Mapped via crcERSpanSessionNo, if crcERSanSessionType from crcERSpanSessionTable has value of eRSpanSource(1), crcRSpanIFIndex is a copy source. If crcERSpanSessionType has value of eRSpanDestination(2), crcRSpanIF ...
crcERSpanIFDirection: This object affects the way traffic is copied from a device's source. If this object has the value 'copyRxOnly(1)', then only traffic received on crcERSpanIFIndex will be copied to the destination. If this object has the value 'copyTxOnly(2)', then only t ...
crcERSpanIFRowStatus: Defines the status of this entry. For this object to be active(1), the crcERSpanSessionRowStatus from crcERSpanSessionTable, mapped via crcERSpanSessionNo, must be active(1). If the said crcERSpanSessionRowStatus transistions to notInService(2) or destro ...
crcERSpanIFOption: Indicates the additional ERSPAN configuration on destination port. - inpkts This bit is set to enable the destination port to receive incoming traffic. - learningDisable This bit is set to suppress MAC learning for incoming traffic at the destination port ...
crcSpanDstPermitListEnabled: Indicates whether the SPAN destination permit list feature is enabled. When crcSpanDstPermitListEnabled is 'true', only ports that have an entry in crcSpanDstPermitListTable are allowed to set as SPAN destination. There is no such restriction when crcSpan ...
crcSpanDstPermitListTable: Contains a list of ports that are configured as allowed SPAN destination ports. Entry of portCopyTable with its portCopyDest can not be created if crcSpanDstPermitListEnabled is 'true' and a corresponding entry does not exist in the crcSpanDstPermitListTa ...
crcSpanDstPermitListEntry: Describes a particular entry that can be set as SPAN destination.
crcSpanDstPermitListRowStatus: Defines the status of this entry. An active entry means that the port of this ifIndex can be set as SPAN destination port. The valid values are active(1), createAndGo(4) and destroy(6).
crcSpanEgressReplicationMode: Describes where SPAN egress packets get replicated, centralized in the device or distributed to where traffic is sourced
crcSpanSessionEgressModeTable: A table containing operational SPAN egress packet replication mode for each SPAN session. A row is created for each SPAN session that is capable of monitoring egress traffic in a device.
crcSpanSessionEgressModeEntry: Describes a particular SPAN session that is capable of monitoring egress traffic.
crcSpanEgressReplicationOperMode: The current egress replication mode in operation.
crcSpanCapacityTable: This table lists the resource capacity for each SPAN session type that is capable of providing such information.
crcSpanCapacityEntry: Indicating resource capacity and usage information for a particular SPAN capacity session type.
crcSpanCapacityType: Indicating the SPAN resource capacity session type. 'allSrc' refers to all SPAN source sessions. 'allDst' refers to all SPAN destination sessions. 'localSrc' refers to local SPAN session where both source and destination ports reside in the same switch. ' ...
crcSpanCapacityShared: Indicating the shared SPAN capacity type. 'none' means the capacity is not shared out of crcSpanSharedSource or crcSpanSharedDestination. 'source' means the capacity is counted against crcSpanSharedSource. The sum of crcSpanUsedSession for all entries wit ...
crcSpanMaxSession: The maximum number of sessions allowed for the SPAN type defined by crcSpanCapacityType. A value of zero indicates no specific limit for this SPAN capacity session type.
crcSpanUsedSession: The number of sessions currently used for the SPAN capacity session type defined.
crcSpanSharedSource: The number of maximum shared span source sessions.
crcSpanSharedDestination: The number of maximum shared span destination sessions.
rmonSampleConfigTable: This table controls the configuration of RMON collection based on statistical sampling techniques, for each monitored interface on the RMON probe. It is a SPARSE-AUGMENTS of the ifEntry found in the IF-MIB module. An entry is created in this table at the ...
rmonSampleConfigEntry: Describes a particular sampling configuration for the indicated RMON-capable interface.
rmonSamplingEnabled: This object affects the way the RMON probe uses statistical sampling to collect packets from the indicated interface. If this object has the value 'false', then the probe will attempt to monitor all packets detected on the indicated interface, in the even ...
rmonMaxAlarms: The maximum number of entries allowed in the alarmTable.
rmonAlarmEnable: This object determines if the RMON alarm feature is enabled/disabled on this device. If this object is set to 'true', the RMON alarm feature enabled. If this object is 'false', RMON alarm feature is disabled. If the RMON feature is disabled, all the RMON ...
rmonConfiguredAlarms: Total number of entries configured in the alarmTable.
rmonConfiguredHcAlarms: Total number of entries configured in the hcAlarmTable.
rmon2ExtensionsGroup: A collection of objects providing configuration extensions for the RMON2-MIB module.
smonExtensionsGroup: A collection of objects providing configuration extensions for the SMON-MIB module.
rmonSampleConfigGroup: A collection of objects providing configuration extensions for RMON agent implementations which support statistical sampling techniques.
smonExtensions2Group: A collection of objects providing additional port copy configuration for destination vlan filtering for the SMON-MIB module.
smonExtensions3Group: A collection of objects providing additional port copy configuration extensions at destination port for the SMON-MIB module. This group is deprecated by smonExtensions8Group.
smonExtensions4Group: A collection of objects providing additional port copy configuration extensions for agent that supports SPAN session concept.
smonExtensions5Group: A collection of objects providing additional port copy configuration extensions for agent that supports local and remote SPAN.
smonExtensions6Group: A collection of objects providing additional port copy information for the SMON-MIB module.
smonExtensions7Group: A collection of objects providing additional port copy configuration extensions for agent that supports reflector port for SPAN session.
rmonAlarmConfigGroup: A collection of objects providing additional RMON configurations to control number alarms and to enable/disable alarms in the alarmTable in RMON-MIB.
smonExtensions8Group: A collection of objects providing additional port copy configuration extensions for agent that supports ingress traffic at destination port for the SPAN session.
crcSpanSessionGroup: A collection of objects providing SPAN session information.
crcERSpanSessionGroup: A collection of objects providing ERSPAN session information.
crcERSpanIFGroup: A collection of objects providing ERSPAN copy source or copy destination information.
crcSpanDstPermitListGroup: A collection of objects used to control selection of destination port information.
smonExtensions9Group: Providing SPAN session description information.
crcERSpanIFOptionGroup: Providing additional port copy configuration extensions for agent that supports ingress traffic at destination port for the ERSPAN session.
crcERSpanSessionGroupRev1: A collection of objects providing ERSPAN session information.
crcSpanEgressReplicationGroup: A collection of objects providing SPAN egress packets replication mode information.
crcSpanCapacityGroup: A collection of objects providing SPAN capacity information.
rmonAlarmCapacityGroup: A collection of objects providing additional RMON,HCRMON configurations details about alarms in the alarmTable in RMON-MIB and hcalarms in cHcAlarmTable in HCALARM-MIB

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list