CISCO-SONET-MIB Download

csConfigTable

The SONET/SDH configuration table. This table has objects for configuring sonet lines.

csConfigEntry

An entry in the table. There is an entry for each SONET line in the table. Entries are automatically created for an ifType value of sonet(39). 'ifAdminStatus' from the ifTable must be used to enable or disable a line. A line is in disabled(down) state unl ...

csConfigLoopbackType

This object specifies the desired loopback mode configuration of the SONET line. The possible values of this objects are follows: noLoopback : Not in the loopback state. lineLocal : The signal transmitted from this interface is connected to the associated ...

csConfigXmtClockSource

Specifies the source of the transmit clock. loopTiming: indicates that the recovered receive clock is used as the transmit clock. localTiming: indicates that a local clock source is used or that an external clock is attached to the box containing the inte ...

csConfigFrameScramble

This object is used to disable or enable the Scrambling option in SONET line.

csConfigType

This object represents the configured line type. Sts is SONET format. Stm is SDH format. sonetSts3c : OC3 concatenated sonetStm1 : European standard OC3 sonetSts12c : OC12 concatenated sonetStm4 : European standard OC12 sonetSts48c : OC48 concat ...

csConfigRDIPType

This object represents the type of RDI-P (Remote Defect Indication - Path) sent by this Network Element (NE) to remote Network Element. onebit : use 1 bit RDI-P threebit : use 3 bit enhanced RDI-P. Default is onebit.

csVTConfigTable

This table contains objects to configure the VT/VC (Virtual Tributary / Virtual Container) related properties of SONET/SDH lines.

csVTConfigEntry

There is an entry in this table for each SONET line that supports SONET virtual tributaries or SDH virtual containers. Each entry in this table will have a corresponding entry in csConfigTable.

csTributaryType

Type of the tributary carried within the SONET/SDH signal. vt15vc11 : carries T1 signal vt2vc12 : carries E1 signal ::= {csVTConfigEntry 1} SYNTAX INTEGER { asynchronous(1), byteSynchronous(2) } MAX-ACCESS read-write STATUS current DESCRIPTION Thi ...

csTributaryFramingType

This object represents the framing type to be assigned to the virtual tributaries in byte sync mapping mode. notApplicable : If VT mapping is not byteSynchronous(2). dsx1ESF : Extended Superframe Format dsx1D4 : Superframe Format Defaul ...

csSignallingTransportMode

This object represents the mode used to transport DS0 signalling information for T1 byteSynchronous mapping (GR253). In signallingTransferMode(2), the robbed-bit signalling is transferred to the VT header. In clearMode(3), only the framing bit is transfer ...

csTributaryGroupingType

This object represents the method used to group VCs into an STM-1 signal. Applicable only to SDH. au3Grouping: STM1<-AU-3<-TUG-2<-TU-12<-VC12 or STM1<-AU-3<-TUG-2<-TU-11<-VC11. au4Grouping: STM1<-AU-4<-TUG-3<-TUG-2<-TU-12<-VC12 or STM1<-AU-4<-TUG-3<-TUG-2 ...

csApsConfigTable

This table contains objects to configure APS (Automatic Protection Switching) feature in a SONET Line. APS is the ability to configure a pair of SONET lines for redundancy so that the hardware will automatically switch the active line from working line to ...

csApsConfigEntry

An entry is created when an APS pair is configured. To create an entry, the following objects must be specified: csApsWorkingIndex, csApsProtectionIndex, csApsEnable, csApsArchMode. The protection line must not be active, i.e, ifAdminStatus must be 'down' ...

csApsWorkingIndex

When a pair of APS lines is configured, one line has to be the working line, which is the primary line, and the other has to be the protection line, which is the backup line. This object refers to the working line in the APS pair. For G.783 AnnexB, this i ...

csApsProtectionIndex

The protection line indicates that it will become the active line when an APS switch occurs (APS switch could occur because of a failure on the working line). For G.783 AnnexB, This index refers to Working Section 2.

csApsEnable

This object is used to enable or disable the APS feature on the working/protection line pairs. When enabled, the hardware will automatically switch the active line from the working line to the protection line within 60ms, or vice versa.

csApsArchMode

This object is used to configure APS architecture mode on the working/protection line pairs. All of the following are supported on single slot. oneToOne(2) is not supported across 2 slots,i.e. the working and protection slot numbers must be the same in o ...

csApsActiveLine

This object indicates which line is currently active. It could be the working line(Section 1 for Annex B), the protection line(Section 2 for Annex B) or none if neither working nor protection line is active. This object reflects the status of receive dire ...

csApsSigFaultBER

This object contains the Bit Error Rate threshold for Signal Fault detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to the -n, where n is between 3 and 5.

csApsSigDegradeBER

This object contains the Bit Error Rate threshold for Signal Degrade detection on the working line. Once this threshold is exceeded, an APS switch will occur. This value is 10 to -n where n is between 5 and 9.

csApsWaitToRestore

This object contains interval in minutes to wait before attempting to switch back to working line. Not applicable if the line is configured in non-revertive mode, i.e. protection line will continue to be active, even if failures on the working line are cl ...

csApsDirection

This object is used to configure the switching direction which this APS line supports. Unidirectional : APS switch only in one direction. Bidirectional : APS switch in both ends of the line.

csApsRevertive

This object is used to configure the APS revertive or nonrevertive option. revertive : Will switch the working line back to active state after the Wait-To-restore interval has expired and the working line Signal-Fault/Signal-Degrade has been cleared. Plea ...

csApsDirectionOperational

This object shows the actual APS direction that is implemented on the Near End terminal. APS direction configured through csApsDirection is negotiated with the Far End and APS direction setting acceptable to both ends is operational at the Near End.

csApsArchModeOperational

This object shows the actual APS architecture mode that is implemented on the Near End terminal. APS architecture mode configured through csApsArchMode object is negotiated with the Far End through APS channel. Architecture mode acceptable to both the Nea ...

csApsChannelProtocol

This object allows to configure APS channel protocol to be implemented at Near End terminal. K1 and K2 overhead bytes in a SONET signal are used as an APS channel. This channel is used to carry APS protocol. Possible values: bellcore(1) : Implements APS c ...

csApsFailureStatus

This object indicates APS line failure status.

csApsSwitchReason

This object indicates APS line switch reason.

csApsPrimarySection

This object indicates which working section is the APS primary section. In G.783 AnnexB, the K1/K2 Bytes are received on the secondary Section. All the Switch Requests are for a switch from the primary section to the secondary section. The object csApsAct ...

csApsLineFailureCode

The object indicates the APS line failure code. This is the failure encountered by the APS line. Refer to CsApsLineFailureCode TC for failure code definitions. The object is used for notifications.

csApsLineSwitchReason

This object indicates the APS line switch reason. When the working line on one end fails, its other end is told to do an APS switch. Refer to CsApsLineSwitchReason TC for more information. The object is used for notifications.

cssTotalTable

The SONET/SDH Section Total table. It contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval. The object 'sonetMediumValidIntervals' from RFC2558 contains the number of 15 minute intervals that have ela ...

cssTotalEntry

An entry in the SONET/SDH Section Total table. Entries are created automatically for sonet lines.

cssTotalESs

The number of Errored Seconds encountered by a SONET/SDH Section in the last 24 hours.

cssTotalSESs

The number of Severely Errored Seconds encountered by a SONET/SDH Section in the last 24 hours.

cssTotalSEFSs

The number of Severely Errored Framing Seconds encountered by a SONET/SDH Section in the last 24 hours.

cssTotalCVs

The number of Coding Violations encountered by a SONET/SDH Section in the last 24 hours.

cssTraceTable

The SONET/SDH Section Trace table. This table contains objects for tracing the sonet section.

cssTraceEntry

An entry in the trace table. Entries exist for active sonet lines. The objects in this table are used to verify continued connection between the two ends of the line.

cssTraceToTransmit

Sonet Section Trace To Transmit. This is string that is transmitted to perform Sonet section trace diagnostics. The trace string is repetitively transmited so that a trace receiving terminal can verify its continued connection to the intended transmitter ...

cssTraceToExpect

Sonet Section Trace To Expect. The receiving terminal verifies if the incoming string matches this string. The value of 'cssTraceFailure' indicates whether a trace mismatch occurred. The default value is a zero-length string.

cssTraceFailure

The value of this object is set to 'true' when Sonet Section received trace does not match the 'cssTraceToExpect'.

cssTraceReceived

This object is used to view the Sonet Section Trace that is received by the receiving terminal.

cslTotalTable

The SONET/SDH Line Total table. It contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval. The object 'sonetMediumValidIntervals' from RFC2558 contains the number of 15 minute intervals that have elapse ...

cslTotalEntry

An entry in the SONET/SDH Line Total table. Entries are created automatically for sonet lines.

cslTotalESs

The number of Errored Seconds encountered by a SONET/SDH Line in the last 24 hours.

cslTotalSESs

The number of Severely Errored Seconds encountered by a SONET/SDH Line in the last 24 hours.

cslTotalCVs

The number of Coding Violations encountered by a SONET/SDH Line in the last 24 hours.

cslTotalUASs

The number of Unavailable Seconds encountered by a SONET/SDH Line in the last 24 hours.

cslFarEndTotalTable

The SONET/SDH Far End Line Total table. It contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval. The object 'sonetMediumValidIntervals' from RFC2558 contains the number of 15 minute intervals that hav ...

cslFarEndTotalEntry

An entry in the SONET/SDH Far End Line Total table. Entries are created automatically for sonet lines.

cslFarEndTotalESs

The number of Errored Seconds encountered by a SONET/SDH Far End Line in the last 24 hours.

cslFarEndTotalSESs

The number of Severely Errored Seconds encountered by a SONET/SDH Far End Line in the last 24 hours.

cslFarEndTotalCVs

The number of Coding Violations encountered by a SONET/SDH Far End Line in the last 24 hours.

cslFarEndTotalUASs

The number of Unavailable Seconds encountered by a SONET/SDH Far End Line in the last 24 hours.

cspTotalTable

The SONET/SDH Path Total table. It contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval.The object 'sonetMediumValidIntervals' from RFC2558 contains the number of 15 minute intervals that have elapsed ...

cspTotalEntry

An entry in the SONET/SDH Path Total table. Entries are created automatically for sonet lines.

cspTotalESs

The number of Errored Seconds encountered by a SONET/SDH Path in the last 24 hours.

cspTotalSESs

The number of Severely Errored Seconds encountered by a SONET/SDH Path in the last 24 hours.

cspTotalCVs

The number of Coding Violations encountered by a SONET/SDH Path in the last 24 hours.

cspTotalUASs

The number of Unavailable Seconds encountered by a SONET/SDH Path in the last 24 hours.

cspFarEndTotalTable

The SONET/SDH Far End Path Total table. Far End is the remote end of the line. The table contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval. The object 'sonetMediumValidIntervals' from RFC2558 conta ...

cspFarEndTotalEntry

An entry in the SONET/SDH Far End Path Total table. Entries are created automatically for sonet lines.

cspFarEndTotalESs

The number of Errored Seconds encountered by a SONET/SDH far end path in the last 24 hours.

cspFarEndTotalSESs

The number of Severely Errored Seconds encountered by a SONET/SDH far end path in the last 24 hours.

cspFarEndTotalCVs

The number of Coding Violations encountered by a SONET/SDH far end path in the last 24 hours.

cspFarEndTotalUASs

The number of Unavailable Seconds encountered by a SONET/SDH far end path in the last 24 hours.

cspTraceTable

The SONET/SDH Path Trace table. This table contains objects for tracing the sonet path.

cspTraceEntry

An entry in the SONET/SDH Path Trace table. The entries exist for active sonet lines. The objects in this table are used to verify continued connection between the two ends of the line.

cspTraceToTransmit

Sonet Path Trace To Transmit. The trace string is repetitively transmited so that a trace receiving terminal can verify its continued receiving terminal can verify its continued connection to the intended transmitter. The default value is a zero-length st ...

cspTraceToExpect

Sonet Path Trace To Expect. The receiving terminal verifies if the incoming string matches this string. The value of 'cspTraceFailure' indicates whether a trace mismatch occured. The default value is a zero-length string.

cspTraceFailure

The value of this object is set to 'true' when Sonet Path received trace does not match the 'cspTraceToExpect'.

cspTraceReceived

This object is used to view the Sonet Path Trace that is received by the receiving terminal.

csStatsTable

The SONET/SDH Section statistics table. This table maintains the number of times the line encountered Loss of Signal(LOS), Loss of frame(LOF), Alarm Indication signals(AISs), Remote failure indications(RFIs).

csStatsEntry

An entry in the SONET/SDH statistics table. These are realtime statistics for the Sonet section, line and path layers. The statistics are gathered for each sonet line. An entry is created automatically and is indexed by ifIndex.

cssLOSs

The number of Loss of signals(LOS) encountered by a SONET/SDH Section. A high value for this object may indicate a problem with the Sonet Section layer.

cssLOFs

The number of Loss of Frames (LOF) encountered by a SONET/SDH Section. A high value for this object may indicate a problem with the Sonet Section layer.

cslAISs

The number of alarm indication signals(AIS) encountered by a SONET/SDH Line. A high value for this object may indicate a problem with the Sonet Line layer.

cslRFIs

The number of remote failure indications (RFI) encountered by a SONET/SDH Line. A high value for this object may indicate a problem with the Sonet Line layer.

cspAISs

The number of alarm indication signals (AIS) encountered by a SONET/SDH Path. A high value for this object may indicate a problem with the Sonet Path layer.

cspRFIs

The number of remote failure indications (RFI) encountered by a SONET/SDH Path. A high value for this object may indicate a problem with the Sonet Path layer.

cspConfigTable

Cisco extension to SONET Path current table.

cspConfigEntry

An entry in Cisco extension to the SONET path current table.

cspSonetPathPayload

Specifies the payload carried by the SONET/SDH Path. The payload specification corresponds to C2 (Signal Label) overhead byte in SONET/SDH Path Overhead: unequipped(1) : Path is not provisioned to carry any payload. unspecified(2) : Path is carrying ...

cspTributaryMappingType

This object represents the VT/VC mapping type. asynchronous: In this mode, the channel structure of DS1/E1 is neither visible nor preserved. byteSynchronous: In this mode, the DS0 signals inside the VT/VC can be found and extracted from the frame. The ini ...

cspSignallingTransportMode

This object represents the mode used to transport DS0 Signalling information for T1 byteSynchronous mapping (GR253). In signallingTransferMode(2), the robbed-bit signalling is transferred to the VT header. In clearMode(3), only the framing bit is transfer ...

csAu4Tug3ConfigEntry

There is an entry in this table for each TUG-3 within a AU-4 SDH path that supports SDH virtual container VC-4. The ifIndex value represents an entry in ifTable with ifType = sonetPath(50).The ifTable entry applicable for this entry belongs to AU-4 path.

csAu4Tug3

This object represents the TUG-3 number.

csAu4Tug3Payload

This object is used for configuring the payload for the tributary group. The possible values are : vc11 : When set to 'vc11' following things are done: - 28 entries created in ifTable for TU-11 with ifType = sonetVT(51) - 28 entries created in ifTable f ...

ciscoSonetConfMIBGroup

Objects used for configuring Sonet lines.

ciscoSonetStatsMIBGroup

These are objects related to Sonet line statistics.

ciscoSonetTraceMIBGroup

Objects related to Sonet line connectivity.

ciscoSonetApsMIBGroup

Objects used for configuring APS over Sonet lines.

ciscoSonetApsMIBGroup1

Objects used for configuring APS over Sonet lines. This group includes 3 new objects in addition to those in the deprecated group ciscoSonetApsMIBGroup.

ciscoSonetConfMIBGroup1

Objects used for configuring Sonet lines.

ciscoSonetVTConfMIBGroup

Objects used for configuring Sonet Virtual tributaries.

ciscoSonetPathConfMIBGroup

Objects used for configuring Sonet Paths.

ciscoSonetNotifEnableGroup

The collection of objects which enable notifications.

ciscoSonetPathConfMIBGroup1

Objects used for configuring Sonet Paths.

ciscoSonetAu4Tug3Group

Objects used for configuring AU-4:TUG-3 paths.