CISCO-VSIMASTER-MIB Download

vsiMasterControllerTable

A table containing a set of VSI controllers. Each controller represents an instance of the VSI Master control protocol. A controller communicates with a set of VSI Slaves across a control interface. Running the VSI protocol, the controller supports a ne ...

vsiMasterControllerEntry

An entry containing management information applicable to a controller which uses the VSI protocol. Controller entries represent internally generated control structures. Therefore each row is created by the agent in response to the learning of a controll ...

vsiControllerIndex

A unique value per VSI controller, greater than 0. This object gets its value from the vsiControllerId, and is used for row selection within the vsiMasterControllerTable.

vsiControllerId

The controller identifier for the VSI controller. Values are arbitrarily assigned by the VSI protocol implementation being managed via this MIB, with local significance only. These values appear in the header of all VSI protocol messages.

vsiCrossConnects

This object contains a value equal to the number of cross-connects being controlled via VSI protocol via this controller.

vsiControllerType

A VSI controller represents an instance of a service layer accessible to a network control application. This object serves to identify the type of the network control application currently being supported by this controller. other(1): the type is unspeci ...

vsiBaseVersionSupported

A VSI Master protocol instance defines internally a set of versions of the protocol that it will support. These versions are numbered, by default, starting from 1. This object makes available the lowest numbered version that the VSI Master protocol supp ...

vsiTopVersionSupported

A VSI Master protocol instance defines internally a set of versions of the protocol that it will support. These versions are numbered, by default, starting from 1. This object makes available the highest numbered version that the VSI Master protocol sup ...

vsiVersionInUse

The number of the VSI version currently being used by this controller. Protocol selection procedures dictate that this should be the highest value of protocol version, between vsiBaseVersionSupported and vsiTopVersionSupported, that is supported by all s ...

vsiSpecifiedVersion

When this object is written with a non-zero value, re-synchronization procedures will be initiated, if necessary, in order to constrain the master and slaves to use the indicated protocol version. When written with zero (0), the master and slaves should u ...

vsiControlInterface

A VSI controller communicates with a set of VSI Slaves across a control interface. The controller is connected to the ATM switch via an ATM link called the Slave Control Link. The interface at the Master end of the link is the Master Control Port, and is ...

vsiLogicalControlInterface

This object describes the instance of a logical interface index bound to the slave end of the Slave Control Link, which is referred to in the description of vsiControlInterface.

vsiControlIfIpAddress

The IP address of the interface identified by the associated vsiControlInterface object.

vsiAvailableChnlWarnThreshold

A controller has in its domain multiple instances of the vsiLogicalIfAvailIngressChnls and vsiLogicalIfAvailEgressChnls counters. This set of values, associated with all the logical interfaces in the vsiLogicalIfTable, is monitored so as to note the mini ...

vsiAvailableChnlAlarmThreshold

A controller has in its domain multiple instances of the vsiLogicalIfAvailIngressChnls and vsiLogicalIfAvailEgressChnls counters. This set of values, associated with all the logical interfaces in the vsiLogicalIfTable, is monitored so as to note the mini ...

vsiAvailableChnlThresholdStatus

As described for the vsiAvailableChnlWarnThreshold and vsiAvailableChnlAlarmThreshold objects, events are generated when these thresholds are crossed. This object defines a set of unique values that are used with the vsiLcnExhaustionNotice to convey info ...

vsiSessionTable

A table containing VSI master-slave session status information. Each VSI controller manages a set of VSI slaves, via a protocol instance called a Session. VSI slaves are entities that reside on the controlled ATM switch. Their number and characteristics ...

vsiSessionEntry

A vsiSessionEntry is a set of objects that together represent the status of each instance of VSI protocol and the slave in an ATM switch to which that instance corresponds. There is one vsiSession for each slave. The number of slaves is discovered via t ...

vsiSessionControllerIndex

The ID of the controller which controls this master-slave session. This identifies which vsiMasterControllerEntry represents the controller communicating with a slave through this Session.

vsiSessionIndex

A VSI controller discovers a set of slaves through VSI protocol. Each of the discovered slaves is bound to a protocol Session and each of these Sessions occupies a row in the vsiSessionTable. This object is the row selector. The value should remain cons ...

vsiSessionVpi

The virtual path identifier for this VSI master-slave session. The Slave Control Link, referred to in the description of vsiLogicalControlInterface, supports an ATM control VC. This is the vpi for that link.

vsiSessionVci

The virtual channel identifier for this VSI master-slave session. The Slave Control Link, referred to in the description of vsiLogicalControlInterface, supports an ATM control VC. This is the vci for that link.

vsiSessionSwitchId

The identifier of the switch which participates in this VSI master-slave session. The switch terminates the virtual circuit identified by the vpi/vci pair referred to by vsiSessionVpi and vsiSessionVci.

vsiSessionSwitchName

The IP hostname for the slave switch which is controlled by this session. This is an ascii string of maximum length 64 characters, learned from the ATM switch.

vsiSessionSlaveId

The identifier of the slave for this VSI master-slave session. This value is learned from the slave on the switch.

vsiSessionState

The state of the VSI session. inactive(1): communications data structures for communicating with the slave have been created, but the VSI protocol has not been started. unknown(2): slave has been queried, but its configuration data has not yet been receiv ...

vsiSessionWindowSize

The maximum number of command messages the VSI master will send before requiring a response from slave. If the value is 0, then flow control is not enabled.

vsiSessionCmdsPending

The number of unacknowledged command messages. The VSI master sends commands to the slave, without receiving acknowledgement, until the window size threshold has been reached. This object is a count of the number of commands that have been sent and that ...

vsiSessionActiveId

ID supplied by the slave to identify the session. This value is interpreted by the master, when a change occurs, to indicate that a resync should be inititated.

vsiSessionPowerupId

ID supplied by the slave to identify the session at powerup. This is the initial value for vsiSessionActiveId, and its default is zero. Changes in vsiSessionActiveId signal a resync.

vsiLogicalIfTable

A table containing information about logical interfaces on the slave switch controlled via VSI. Logical interfaces are an abstraction of exposed, external ATM interfaces that are available for connections. When two external interfaces, represented by tw ...

vsiLogicalIfEntry

An entry containing information about a single VSI logical interface. Entries are instantiated and removed as signalled by the slave which controls the external interface. Each entry contains information about the capacity of cross-connects the interfac ...

vsiLogicalIfControllerIndex

The VSI controller index of the controller through which this logical interface was learned.

vsiLogicalIfIndex

A unique value, greater than zero, for each VSI logical interface. Logical interface numbers are selected by the switch to be unique and persistent. The same number is preserved through power failures. This index is not the same as an ifIndex. It is a ...

vsiLogicalIfName

The physical descriptor of the logical interface, as reported by the VSI slave. It is distinct from ifName.

vsiLogicalIfOperState

The VSI operational state of the logical interface as reported to the VSI master by the VSI slave. removed(1): the interface is not a valid interface on this controller, is not part of the controller's partition, or is not available. active(2): the interf ...

vsiLogicalIfAdminState

The current administrative (configured) state of the interface, as reported to the VSI master by the VSI slave. down(1): the interface is not a valid interface for the controller. up(2): the interface is configured for use by the controller. pendingDown(3 ...

vsiLogicalIfRxCells

The number of cells received via this logical interface as reported to the VSI master by the VSI slave.

vsiLogicalIfTxCells

The number of cells transmitted via this logical interface as reported to the VSI master by the VSI slave.

vsiLogicalIfRxCellsDiscarded

The number of received cells discarded by this logical interface as reported to the VSI master by the VSI slave.

vsiLogicalIfTxCellsDiscarded

The number of transmitted cells discarded by this logical interface as reported to the VSI master by the VSI slave.

vsiLogicalIfRxHeaderErrors

The number of cells received via this logical interface which had header errors, as reported to the VSI master by the VSI slave.

vsiLogicalIfRxInvalidAddrs

The number of cells received by this logical interface which had invalid addresses, as reported to the VSI master by the VSI slave. An unknown vpi/vci value set is an example of of an invalid address.

vsiLogicalIfEndPointsInUse

The number of end points in use on this logical interface, as reported to the VSI master by the VSI slave. This reflects an aggregate count of input, output and bi-directional end points. If the logical interface has not been removed, but does not curren ...

vsiLogicalIfAvailIngressChnls

The number of ingress channels available for this logical interface, as reported to the VSI master by the VSI slave.

vsiLogicalIfAvailEgressChnls

The number of egress channels available for this logical interface, as reported to the VSI master by the VSI slave.

vsiLogicalIfAvailIngressCellRate

The available ingress cell rate in cells/second for the logical interface, as reported to the VSI master by the VSI slave.

vsiLogicalIfAvailEgressCellRate

The available egress cell rate in cells/second for the logical interface, as reported to the VSI master by the VSI slave.

vsiLogicalIfVcMergeSupported

If this object has the value true(1) then VC merge capability is supported for this logical interface. Otherwise VC merge capability is not supported on this logical interface.

vsiLogicalIfMulticastSupported

If this object has the value true(1) then multicast capability is supported for this logical interface. Otherwise multicast capability is not supported on this logical interface.

vsiLogicalIfVpiTranslated

If this object has the value true(1) then vpi values entering on this logical interface are translated at the other end of the link. This translation may be an indication that the link is supporting a tunnel. Otherwise, vpi values are not translated for ...

vsiLogicalIfStrictSigRange

If this object has the value true(1) then signalling addresses must be in the strict advertised range for the high-address (vpi). Otherwise, signalling addresses are not so constrained.

vsiLogicalIfMaxIngressCellRate

The maximum ingress cell rate in cells/second for the logical interface, as reported to the VSI. This value is the limiting value for vsiLogicalIfAvailIngressCellRate.

vsiLogicalIfMaxEgressCellRate

The maximum egress cell rate in cells/second for the logical interface, as reported to the VSI master by the VSI slave.

vsiLogicalIfMinVpi

Minimum allowed vpi value for this interface as reported by VSI slave switch.

vsiLogicalIfMaxVpi

Maximum allowed vpi value for this interface as reported by VSI slave switch.

vsiLogicalIfMinVci

Minimum allowed vci value for this interface as reported by VSI slave switch.

vsiLogicalIfMaxVci

Maximum allowed vci value for this interface as reported by VSI slave switch.

vsiLogicalControlIfIndex

The interface index for the interface which controls this logical interface. This is the ifIndex of the controlling network layer interface, and is a direct manifestation of the mapping between a logical interface and the real ifIndex.

vsiLogicalIfSessionIndex

All logical interfaces are in the domain of a VSI slave, which communicates with the VSI master through a Session. This object is a selector for an entry in the table vsiSessionTable. It is the VSI session index for the VSI session which controls this lo ...

vsiXCTable

A table containing information about cross-connects on the slave switch controlled via VSI. cross-connects represent virtual links across two interfaces. The participating interfaces that support these links are represented in this MIB by the vsiLogical ...

vsiXCEntry

An entry containing information about one unidirectional or bidirectional cross-connect on the slave switch controlled via VSI. A VSI controller represents an instance of a service layer accessible to a network control application. The application create ...

vsiXCControllerIndex

The index of the VSI controller through which this cross-connect was instantiated. This object is the index for a vsiControllerTable entry; the controller indexed is the VSI protocol partner to the slave that is controlling the logical interfaces on wh ...

vsiXCLogicalIfLow

The VSI logical interface index for the first endpoint of the cross-connect. This object is the selector index for one of the two vsiLogicalIfTable entries that support this cross-connect. Further, this index value is constrained to be 'numerically lowe ...

vsiXCLogicalIfHi

The VSI logical interface index for the second endpoint of the cross-connect. This object is the selector index for one of the two vsiLogicalIfTable entries that support this cross-connect. Further, this index value is constrained to be 'numerically hig ...

vsiXCIndex

A unique value greater than zero, for each cross-connect within the set of VsiXCTable entries indexed by vsiXCLogicalIfLow and vsiXCLogicalIfHi. The value should remain constant after a cross-connect is initialized. These values are assigned in sequence ...

vsiXCState

The operational state of the cross-connect, as reported to the VSI master by the VSI slave. deleted(1): the connection does not exist. reserved(2): connection is in the reserved state. committed(3): connection is in the committed state. reservedFail(4): c ...

vsiXCVpiLow

The vpi of that endpoint of the cross-connect which terminates on the logical interface whose index is given by vsiXCLogicalIfLow.

vsiXCVciLow

The vci of that endpoint of the cross-connect which terminates on the logical interface whose index is given by vsiXCLogicalIfLow.

vsiXCVpiHi

The vpi of that endpoint of the cross-connect which terminates on the logical interface whose index is given by vsiXCLogicalIfHi.

vsiXCVciHi

The vci of that endpoint of the cross-connect which terminates on the logical interface whose index is given by vsiXCLogicalIfHi.

vsiControllerTrapEnable

If this object is true, both vsiControllerAdded and vsiControllerDeleted notifications are enabled.

vsiSessionTrapEnable

If this object is true, both vsiSessionUp and vsiSessionDown notifications are enabled.

vsiLogicalIfTrapEnable

If this object is true, both vsiLogicalIfUp and vsiLogicalIfDown notifications are enabled.

vsiXCTrapEnable

If this object is true, both vsiXCFailed and vsiLcnExhaustionNotice notifications are enabled.

vsiVSITrapEnable

If this object is true, all of vsiControllerTrapEnable, vsiSessionTrapEnable, vsiLogicalIfTrapEnable, and vsiXCTrapEnable are also set to true. This allows for enabling and disabling all notifications as a group.

ciscoVsiMasterGeneralGroup

Objects that apply to all VSI Master implementations.

ciscoVsi2MasterGroup

Objects that apply to all VSI Master implementations.

ciscoVsi2AlarmControlGroup

Collection of objects needed to control (enable and disable) the generation of associated Notifications.