DES3018-L2MGMT-MIB Download

--swL2DevInfoSystemUpTime

-- "The value of sysUpTime at the time the switch entered its -- current operational state. If the current state was entered -- prior to the last re-initialization, then this object contains -- a zero value. This value is in un ...

swL2Module-2-Type

This object indicates the module type.

swL2CPUutilizationIn5sec

Time scale is 5 seconds.The value will be between 0%(idle) and 100% (very busy).

swL2CPUutilizationIn1min

Time scale is 1 minute.The value will be between 0%(idle) and 100% (very busy).

swL2CPUutilizationIn5min

Time scale is 5 minute.The value will be between 0%(idle) and 100% (very busy).

swL2DevCtrlSystemReboot

This object indicates the agent system reboot state. The agent always returns other(1) when this object is read.

swL2DevCtrlSystemIP

This object indicates system ip.

swL2DevCtrlSubnetMask

This object indicates system subnet mask.

swL2DevCtrlDefaultGateway

This object indicates system default gateway.

swL2DevCtrlManagementVlanId

This object controls which Vlan includes system ip. And the Vlan should have been created.

swL2DevCtrlStpState

This object can be enabled or disabled spanning tree algorithm during runtime of the system.

swL2DevCtrlIGMPSnooping

This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled .

swL2DevCtrlBcastStormCtrl

-- "This object indicates broadcast storm control function is enabled or -- disabled. The swL2PortCtrlBMDStormLimit object will descript the -- detail about the storm control . -- "This object indicates ...

swL2DevCtrlSnmpEnableAuthenTraps

Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it i ...

swL2DevCtrlIpAutoConfig

Indicates the status of automatically getting configuration from TFTP server on device

swL2PortCtrlMulticastfilter

This object decide the multicast packets filtering mode on all port .

swL2MACNotifyState

This object can enabled or disabled MAC Notification.

swL2MACNotifyHistorySize

This object indicates the history size of variation MAC in address table. The default value is 1 .

swL2MACNotifyInterval

This object indicates the time interval in second for trigger the MAC notify message.

swL2PortInfoTable

A table that contains information about every port.

swL2PortInfoEntry

A list of information for each port of the device.

swL2PortInfoPortIndex

This object indicates the module's port number.(1..Max port number in the module)

--swL2PortInfoType

-- "This object indicates the connector type of this port. -- "Provides port type information in displayed string format This object indicates the port link status.

swL2PortInfoNwayStatus

This object indicates the port speed and duplex mode.

swL2PortCtrlTable

A table that contains control information about every port.

swL2PortCtrlEntry

A list of control information for each port of the device.

swL2PortCtrlPortIndex

This object indicates the module's port number.(1..Max port number in the module)

swL2PortCtrlAdminState

This object decide the port enabled or disabled.

swL2PortCtrlNwayState

Chose the port speed, duplex mode, and N-Way function mode.

swL2PortCtrlFlowCtrlState

Set flow control function as enabled or disabled.

swL2PortCtrlDescription

The object describe the ports in text.

swL2PortErrEntry

A list of information for err port of the device.

swL2PortErrPortIndex

This object indicates the module's port number.(1..Max port number in the module)

swL2PortErrPortState

This object decide the portstate enabled or disabled.

swL2PortErrPortStatus

This object decide the PortStatus whether err-disabled.

swL2PortErrPortReason

This object decide the PortStatus STP LBD or Storm control.

swL2PortErrDescription

The object describe the ports in text.

swL2QOSBandwidthControlTable

.

swL2QOSBandwidthControlEntry

A list of information contained in swL2QOSBandwidthControlTable.

swL2QOSBandwidthPortIndex

Indicates the port .

swL2QOSBandwidthRxRate

Indicates RX Rate(Mbit/sec) of the specifed port.Value 1024000 means no limit.

swL2QOSBandwidthTxRate

Indicates TX Rate(Mbit/sec) of the specifed port.Value 1024000 means no limit.

swL2QOSSchedulingTable

.

swL2QOSSchedulingEntry

A list of information contained in swL2QOSSchedulingTable.

swL2QOSSchedulingClassIndex

Indicates the hardware queue number.

swL2QOSSchedulingMaxPkts

-- "Indicates the maximum number of packets the hardware priority queue will be allowed -- to transmit before allowing the next lowest priority queue to transmit its packets. -- a value between 0 and 255 can be specified. -- " ...

swL2QOSSchedulingMechanismCtrl

This object can control QOS scheduling Mechanism.

swL2QOS8021pUserPriorityTable

.

swL2QOS8021pUserPriorityEntry

A list of information contained in swL2QOS8021pUserPriorityTable.

swL2QOS8021pUserPriorityIndex

The 802.1p user priority .

swL2QOS8021pUserPriorityClass

The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).

swL2QOS8021pDefaultPriorityTable

.

swL2QOS8021pDefaultPriorityEntry

A list of information contained in swL2QOS8021pDefaultPriorityTable.

swL2QOS8021pDefaultPriorityIndex

Indicates the port number .

swL2QOS8021pDefaultPriority

The priority value to assign to untagged packets received by the switch ports on the switch..

swPortTrunkMaxPortMembers

The max number of ports allowed in a trunk.

swPortTrunkTable

This table specifies the port membership for each logical link.

swPortTrunkEntry

A list of information specifies which ports group form a single logical link.

swPortTrunkIndex

The index of logical port trunk.

swPortTrunkMasterPort

The object indicates the master port number of the port trunk entry.The first port of the trunk is implicitly configured to be the master logical port.When using Port Trunk, you can not configure the other ports of the group except the master port. Their ...

swPortTrunkPortList

Indicate member ports of a logical trunk.

swPortTrunkType

This object indicates the type of this entry.

swPortTrunkActivePort

This object indicates the active ports of this entry.

swPortTrunkState

This object indicates the status of this entry. when the state is CreatAndGo(4),the type of trunk is static(1); when the state is CreatAndWait(5),the type of trunk is lacp(2). ::= { swPortTrunkEntry 6 } SYNTAX Integer32 MAX-ACCESS read-only STATUS current ...

swL2TrunkAlgorithm

This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.

swL2TrunkLACPPortTable

This table specifys which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkLACPPortEntry

A list of information specifies which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkLACPPortIndex

The index of logical port lacp.

swL2TrunkLACPPortState

The state of logical port lacp.

swPortMirrorTxPortList

This object indicates the Tx port list of ports to be sniffed.

swPortMirrorTargetPort

This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.

swL2IGMPMaxSupportedVlans

Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).

swL2IGMPMaxIpGroupNumPerVlan

Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).

swL2IGMPCtrlEntry

The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.

swL2IGMPQueryInterval

The frequency at which IGMP Host-Query packets are transmitted on this switch.

swL2IGMPMaxResponseTime

The maximum query response time on this switch.

swL2IGMPRobustness

The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.

swL2IGMPLastMemberQueryInterval

The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.

swL2IGMPHostTimeout

The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.

swL2IGMPRouteTimeout

The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.

swL2IGMPLeaveTimer

When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.

swL2IGMPQueryState

This object decide the IGMP query enabled or disabled.

swL2IGMPCurrentState

This object indicates the current IGMP query state.

swL2IGMPCtrlState

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - ...

swL2IGMPFastLeave

swL2IGMPQueryInfoTable

The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.

swL2IGMPQueryInfoEntry

Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.

swL2IGMPInfoQueryCount

This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.

swL2IGMPInfoTxQueryCount

This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.

swL2IGMPInfoTable

The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, ...

swL2IGMPInfoEntry

Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.

swL2IGMPVid

This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.

swL2IGMPGroupIpAddr

This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.

swL2IGMPMacAddr

This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.

swL2IGMPPortMap

This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit re ...

swL2IGMPIpGroupReportCount

This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.

swL2TrafficCtrlEntry

A list of information specifies the storm traffic control configuration.

swL2TrafficCtrlGroupIndex

The index of logical port trunk. The trunk group number depend on the existence of unit and module.

swL2TrafficCtrlUnitIndex

Indicates ID of the unit in the device

swL2TrafficCtrlBMStromthreshold

This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlUcastStromCtrl objects whether is enabled) will active storm control. Whenever a port ...

swL2TrafficCtrlBcastStromCtrl

This object indicates broadcast storm control function is enabled or disabled.

swL2TrafficCtrlMcastStromCtrl

This object indicates multicast storm control function is enabled or disabled.

swL2TrafficCtrlUcastStromCtrl

This object indicates destination lookup fail function is enabled or disabled.

swL2TrafficSegTable

This table specifys the port just can forward traffic to the specific port list.

swL2TrafficSegEntry

A list of information specifies the port with its traffic forward list.

swL2TrafficSegPort

The port number of the logical port.

swL2TrafficSegForwardPorts

The port list that the specific port can forward traffic.

swL2PortSecurityControlTable

port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this ...

swL2PortSecurityControlEntry

A list of information contained in swL2PortSecurityControlTable.

swL2PortSecurityPortIndex

Indicates the secured port to lock address learning.

swL2PortSecurityMaxLernAddr

Indicates allowable number of addresses to be learned at this port.

swL2PortSecurityMode

Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In delet ...

swL2PortSecurityAdmState

Indicates administration state of locking address.

swL2PortSecurityTrapLogState

when enable(2),whenever there's a new MAC that violates the pre-defined port security configuration, trap will be sent out and the relevant information will be logged in system.

swL2StpLbd

Indicates whether STP loop-back prevent on the device is turned on

swL2StpLbdRecoverTime

The period of time on which STP module keeps checking the BPDU loop status, to configure swL2StpLbdRecoverTime as 0 disables automatically recover

swL2StpPortTable

A table that contains port-specific information for the Spanning Tree Protocol.

swL2StpPortEntry

A list of information maintained by every port about the Spanning Tree Protocol state for that port.

swL2StpPort

The port number of the port for this entry.

swL2StpPortLbd

The enabled/disabled status is used to Loop-back prevention attached to this port.

swL2StpPortStatus

When the port Enable state is enabled, the port's current state as defined by application of the Spanning Tree Protocol. If the PortEnable is disabled, the the port status will be no-stp-enabled(7). If the port is in error disabled status, the port status ...

swL2StpPortRole

When the port Enable state is enabled, the port's current port role as defined by application of the Spanning Tree Protocol. If the Port Enable state is disabled, the the port role will be nonstp(7). If the port is in loop-back status, the port role will ...

swL2StpPortFBPDU

The enabled/disabled status is used to BPDU Filtering attached to this port.

swL2StpPortLinkState

This object indicates the stp port speed and duplex mode.

swL2StpPortProtocolMigration

When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.

swL2StpPortAdminEdgePort

The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed as an edge-port and a value of FALSE(2) indicates that this port should be assumed as a non-edge-port.

swL2StpPortOperEdgePort

The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU.

swL2StpPortAdminPointToPoint

The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this por ...

swL2StpPortOperPointToPoint

The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpP ...

swL2StpPortAdminPathCost

The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is b ...

swL2StpPortPriority

The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of swL2StpPort.

swL2STPPortState

The enabled/disabled status is usedoop-back prevention attached to this port.

swL2CosPriorityTable

Used to show and config per port priority-based QoS features on the switch

swL2CosPriorityEntry

A list of information contained in swL2CosPriorityTable.

swL2CosPriorityPort

The port number of CoS Priority.

swL2CosPriorityPortPRI

Indicates port_priority state for CoS.

swL2CosPriorityEtherPRI

Enable Ethernet frame based priority. When set ether8021p(2), enable 802.1p QoS; When set macBase(3), enable MAC-based QoS; When set disable(1), disable Ethernet frame based priority.

swL2CosPriorityIpPRI

Enable IP priority QoS. When set tos(2), enable TOS based QoS; When set dscp(3), enable DSCP based QoS; When set disable(1), disable IP priority QoS.

swL2CosPriorityNone

when read,it always return invalid(2); when write valid(1),it disables all priority in this table.

swL2CosPortPRITable

Used to show port-to-class mappings and map specific port to one of the hardware queues available on the switch.

swL2CosPortPRIEntry

A list of information contained in swL2CosPortPRITable.

swL2CosPortPRIIndex

Indicates CoS Priority PortPRI.

swL2CosPortPRIClass

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges ...

swL2CosMacBasePRITable

Used to show MAC priority map to traffic class and map the destination MAC address in incoming packet to one of the hardware queues available on the switch.

swL2CosMacBasePRIEntry

A list of information contained in swL2CosMacBasePRITable.

swL2CosMacBasePRIIndex

Indicates CoS Priority MacBasePRI.

swL2CosMacBasePRIClass

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges ...

swL2CosTosPRITable

Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.

swL2CosTosPRIEntry

A list of information contained in swL2CosTosPRITable.

swL2CosTosPRIIndex

Indicates CoS Priority TosPRI.

swL2CosTosPRIClass

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges ...

swL2CosDscpPRITable

Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.

swL2CosDscpPRIEntry

A list of information contained in swL2CosDscpPRITable.

swL2CosDscpPRIIndex

Indicates CoS Priority DscpPRI.

swL2CosDscpPRIClass

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges ...

swL2LoopDetectAdminState

This object indicates the loopback detection status for the system.

swL2LoopDetectInterval

This object indicates the interval value, the range is from 1 to 32767 seconds.

swL2LoopDetectRecoverTime

This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.

swL2LoopDetectPortTable

The table specifies the loopback detection function specified by port.

swL2LoopDetectPortEntry

The table specifies the loopback detection function specified by port.

swL2LoopDetectPortIndex

This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module

swL2LoopDetectPortState

This object indicates the loopback detection function state on the port.

swL2LoopDetectPortLoopStatus

This object indicates the port status.

swL2VlanTable

A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

swL2VlanEntry

Static information for a VLAN configured into the device by (local or network) management.

swL2VlanIndex

The VLAN ID of the VLAN to be created. The range is 1 - 4094.

swL2VlanName

The name of the VLAN to be displayed.

swL2VlanType

The type of the VLAN to be displayed.

swL2VlanMemberPorts

A range of member ports to the VLAN.

swL2VlanStaticPorts

A range of static ports to the VLAN.

swL2VlanUntaggedPorts

Specifies the additional ports as untagged.

swL2VlanTaggedPorts

Specifies the additional ports as tagged.

swL2macNotifyInfo

This object indicates the last time reboot information.

swL2PortSecurityViolationMac

This object indicates the MAC address that violates the port security configuration.