DES3627-SWL3MGMT-MIB

DES3627-SWL3MGMT-MIB Download

MIBs list

The Structure of Layer 3 Network Management Information for the proprietary enterprise.

IPHost Network Monitor offer an easy way of SNMP monitoring your D-Link Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for DES3627-SWL3MGMT-MIB

swL3DevCtrlRIPState
This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled.
swL3DevCtrlOSPFState
This object indicates OSPF protocol is enabled or disabled.
swL3DevCtrlDVMRPState
This object indicates DVMRP protocol is enabled or disabled.
swL3DevCtrlVRRPState
This object indicates VRRP protocol is enabled or disabled.
swL3DevCtrlVrrpPingState
This object indicates VRRP protocol Ping is enabled or disabled.
swL3DevCtrlDHCPAutoConfigState
This object indicates auto config is enabled or disabled.
swL3IpCtrlEntry
A list of information about a specific IP interface.
swL3IpCtrlInterfaceName
This object indicates the name of the IP interface.
swL3IpCtrlIfIndex
This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
swL3IpCtrlIpAddr
The IP address of the interface. This object only can take the value of the unicast IP address.
swL3IpCtrlIpSubnetMask
The IP net mask for this interface.
swL3IpCtrlVlanName
This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
swL3IpCtrlProxyArp
-- "This object indicates enable/disable of the proxy ARP function for IPv4. When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.
swL3IpCtrlMode
This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. ...
swL3IpCtrlAdminState
The state of the IP interface.
swL3IpCtrlIpv4AdminState
-- "The IPv4 admin state of the IP interface. The default state is determined by project. -- This state will only be effective when the swL3IpCtrlAdminState is enabled. -- "The current IPv4 operational state of the IP int ...
swL3IpCtrlIpv6LinkLocalPrefixLen
The IPv6 prefix length for this IPv6 link local address.
swL3IpCtrlState
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
swL3IpCtrlIpv6LinkLocalAutoState
The state of the IPv6 link local auto.
swL3IpCtrlProxyArpLocalState
-- "If the state is enabled, the switch will be allowed to respond to the proxy ARP -- when the source IP and destination IP are in the same interface. This table contains IPv6 information of an IP interface.
swL3Ipv6CtrlEntry
A list of IPv6 information about a specific IP interface.
swL3Ipv6CtrlInterfaceName
This object indicates the name of the IP interface.
swL3Ipv6CtrlMaxReassmblySize
Maximum Reassembly Size of the IP interface.
swL3Ipv6CtrlNsRetransTimer
Neighbor solicitation's retransmit timer. The unit is set in milliseconds.
swL3Ipv6CtrlRaMinRtrAdvInterval
The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval
swL3Ipv6CtrlRaMaxRtrAdvInterval
The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.
swL3Ipv6CtrlRaLifeTime
Indicates the lifetime of the router as the default router.
swL3Ipv6CtrlRaReachableTime
Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.
swL3Ipv6CtrlRaRetransTime
Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.
swL3Ipv6CtrlRaHopLimit
Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.
swL3Ipv6CtrlRaManagedFlag
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.
swL3Ipv6CtrlRaOtherConfigFlag
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.
swL3Ipv6AddressCtrlTable
This table contain IPv6 address information for each IP interface.
swL3Ipv6AddressCtrlEntry
A list of information about a specific IPv6 address.
swL3Ipv6AddressCtrlInterfaceName
This object indicates the name of the IP interface.
swL3Ipv6Address
Specify the IPv6 address.
swL3Ipv6AddressCtrlPrefixLen
Indicates the prefix length of this IPv6 address.
swL3Ipv6AddressCtrlPreferredLifeTime
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.
swL3Ipv6AddressCtrlValidLifeTime
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.
swL3Ipv6AddressCtrlOnLinkFlag
When enabled, the address implied by the specified prefix is available on the link where the RA message is received.
swL3Ipv6AddressCtrlAutonomousFlag
When enabled, the specified prefix will be used to create an autonomous address configuration.
swL3Ipv6AddressCtrlState
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
swL3IpCtrlAllIpIfState
This object indicates all interface function state of the device.
swL3IpFdbInfoTable
A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
swL3IpFdbInfoEntry
Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
swL3IpFdbInfoIpSubnetMask
A IP net mask for this interface.for which switch has forwarding and/or filtering information.
swL3IpFdbInfoPort
Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that swi ...
swL3IpFdbInfoType
The status of this entry.
swL3IpStaticRouteTable
This entity's IP static Routing table.
swL3IpStaticRouteEntry
A particular route to a particular destination, under a particular policy. Once an entry is built,it shouldn't be modified.That is,it just supports create and delete actions.
swL3IpStaticRouteDest
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the v ...
swL3IpStaticRouteMask
Indicate the mask to be logical-AND with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpS ...
swL3IpStaticRouteBkupState
The routing state for this route.The value SHOULD be primary(1), backup(2) or none(3).
swL3IpStaticRouteNextHop
Specifies the IP address for the next hop router. An IP address of 255.255.255.255 denotes a Null interface as the next hop.
swL3IpStaticRouteMetric
Specifies the routing metric for this route.
swL3IpStaticRouteStatus
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresp ...
swL3IpStaticRouteWeight
Specifies the weight value. Used for the weighted multipath.
swL3IpStaticRouteInterfaceName
Specifies the name of the IP interface.
swL3RelayDhcpState
This object indicates Dhcp Relay function is enabled or disabled.
swL3RelayDhcpHopCount
This object indicates the maximum number of router hops that the BOOTP packets can cross.
swL3RelayDhcpTimeThreshold
This object indicates the minimum time in seconds within which the switch must relay the Dhcp request. If this time is exceeded, the switch will drop the Dhcp packet.
swL3RelayDhcpCtrlTable
This table specifys the IP address as a destination to forward (relay) DHCP packets to.
swL3RelayDhcpCtrlEntry
A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.
swL3RelayDhcpCtrlInterfaceName
The name of the IP interface.
swL3RelayDhcpCtrlServer
The DHCP server IP address.
swL3RelayDhcpCtrlState
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresp ...
swL3RelayDhcpOption82State
This object indicates DHCP Relay Option 82 function is enabled or disabled.
swL3RelayDhcpOption82CheckState
This object indicates DHCP Relay Option 82 Check function is enabled or disabled.
swL3RelayDhcpOption82Policy
This object indicates DHCP Relay Option 82 Policy.
swL3RelayDnsState
This object indicates DNS Relay function is enabled or disabled.
swL3RelayDnsPrimaryServer
This object indicates the address of the primary DNS server.
swL3RelayDnsSecondaryServer
This object indicates the address of the secondary DNS server.
swL3RelayDnsCacheState
This object indicates DNS Relay cache is enabled or disabled.
swL3RelayDnsStaticTableState
This object indicates DNS Relay static table is enabled or disabled.
swL3RelayDnsCtrlTable
This table display the current DNS relay static table.
swL3RelayDnsCtrlEntry
A list of information display the current DNS relay static table.
swL3RelayDnsCtrlDomainName
The domain name of the entry.
swL3RelayDnsCtrlIpAddr
The IP address of the entry.
swL3RelayDnsCtrlState
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresp ...
swL3Md5Table
This table display the current MD5 key table.
swL3Md5Entry
A list of information display the current MD5 key table.
swL3Md5KeyId
The MD5 key ID.
swL3Md5Key
An MD5 password of up to 16 bytes.
swL3Md5RowStatus
This object indicates the status of this entry.
swL3RouteRedistriTable
Route redistribution allows routers on the network. That are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the vairous routers routing tables and assinging appropriate metrics ...
swL3RouteRedistriEntry
A list of information display the route redistribution table.
swL3RouteRedistriSrcProtocol
Allows the selection of the protocol of the source device.
swL3RouteRedistriDstProtocol
Allows the selection of the protocol of the destination device.
swL3RouteRedistriType
Allows the selection of one of the methods for calcalculating the metric value.
swL3RouteRedistriMetric
Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.
swL3RouteRedistriRowStatus
This object indicates the status of this entry.
swL3OspfHostTable
The list of Hosts, and their metrics, that the router will advertise as host routes.
swL3OspfHostEntry
A metric to be advertised, for a given type of service, when a given host is reachable.
swL3OspfHostIpAddress
The IP Address of the Host.
swL3OspfHostTOS
The Type of Service of the route being configured.
swL3OspfHostMetric
The Metric to be advertised.
swL3OspfHostAreaID
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0
swL3OspfHostStatus
This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3ospfVirtIfTable
Information about this router's virtual inter- faces.
swL3ospfVirtIfEntry
Information about a single Virtual Interface.
swL3ospfVirtIfAreaId
The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
swL3ospfVirtIfNeighbor
The Router ID of the Virtual Neighbor.
swL3ospfVirtIfTransitDelay
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
swL3ospfVirtIfRetransInterval
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should b ...
swL3ospfVirtIfHelloInterval
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.
swL3ospfVirtIfRtrDeadInterval
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor.
swL3ospfVirtIfState
OSPF virtual interface states.
swL3ospfVirtIfEvents
The number of state changes or error events on this Virtual Link
swL3ospfVirtIfAuthType
The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.
swL3ospfVirtIfAuthKey
If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Lar ...
swL3ospfVirtIfAuthKeyID
The MD5 key ID.
swL3ospfVirtIfStatus
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3ospfIfTable
The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF.
swL3ospfIfEntry
The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF.
swL3ospfIfIpAddress
The IP address of this OSPF interface.
swL3ospfAddressLessIf
For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.
swL3ospfIfAreaId
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
swL3ospfIfType
The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', a ...
swL3ospfIfAdminStat
The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
swL3ospfIfRtrPriority
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular netw ...
swL3ospfIfTransitDelay
The estimated number of seconds it takes to transmit a link state update packet over this interface.
swL3ospfIfRetransInterval
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.
swL3ospfIfHelloInterval
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.
swL3ospfIfRtrDeadInterval
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common netw ...
swL3ospfIfPollInterval
The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.
swL3ospfIfState
The OSPF Interface State.
swL3ospfIfDesignatedRouter
The IP Address of the Designated Router.
swL3ospfIfBackupDesignatedRouter
The IP Address of the Backup Designated Router.
swL3ospfIfEvents
The number of times this OSPF interface has changed its state, or an error has occurred.
swL3ospfIfMulticastForwarding
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMult ...
swL3ospfIfDemand
Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.
swL3ospfIfAuthType
The authentication type specified for an in- terface. Additional authentication types may be assigned locally.
swL3ospfIfAuthKey
The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and s ...
swL3ospfIfAuthKeyID
The MD5 key ID.
swL3ospfIfPassiveMode
Assign the designated entry to be a passive interface.
swL3ospfIfStatus
-- "This variable displays the status of the en- -- try. Setting it to 'invalid' has the effect of -- rendering it inoperative. The internal effect -- (row removal) is implementation dependent. The Metric to be ...
swL3RoutePreferenceRIP
Used to configure the route preference of RIP.
swL3RoutePreferenceOSPFIntra
Used to configure the route preference of OSPF Intra.
swL3RoutePreferenceStatic
Used to configure the route preference of Static.
swL3RoutePreferenceLocal
Used to read the route preference of Local.
swL3RoutePreferenceOSPFInter
Used to configure the route preference of OSPF Inter.
swL3RoutePreferenceOSPFExtT1
Used to configure the route preference of OSPFExtT1.
swL3RoutePreferenceOSPFExtT2
Used to configure the route preference of OSPF ExtT2.
swL3ospfAreaTable
Information describing the configured parame- ters and cumulative statistics of the router's attached areas.
swL3ospfAreaEntry
Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas.
swL3ospfAreaId
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
swL3ospfAreaType
The type specified for an area.
swL3ospfAreaSummaryState
Whether the summary LSA is effective for this area.
swL3ospfAreaMetric
Enter the metric (1 - 65535; 0 for auto cost) of this area.
swL3ospfAreaTranslateState
.
swL3ospfAreaStatus
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
swL3dvmrpInterfaceTable
The (conceptual) table listing the router's multicast- capable interfaces.
swL3dvmrpInterfaceEntry
An entry (conceptual row) in the dvmrpInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides.
swL3dvmrpInterfaceIfIndex
The ifIndex value of the interface for which DVMRP is enabled.
swL3dvmrpInterfaceLocalAddress
The IP address this system will use as a source address on this interface. On unnumbered interfaces, it must be the same value as dvmrpInterfaceLocalAddress for some interface on the system.
swL3dvmrpInterfaceMetric
The distance metric for this interface which is used to calculate distance vectors.
swL3dvmrpInterfaceProbe
the period of sending probe
swL3dvmrpInterfaceNbrTimeout
the timer when neighbor expired.
swL3dvmrpInterfaceStatus
The status of this entry. Creating the entry enables DVMRP on the virtual interface; destroying the entry or setting it to notInService disables DVMRP on the virtual interface.
swL3dvmrpInterfaceRcvBadPkts
The number of DVMRP packets received on the interface by the DVMRP process which were subsequently discarded as invalid (e.g. invalid packet format, or a route report from an unknown neighbor).
swL3dvmrpInterfaceRcvBadRoutes
The number of routes, in valid DVMRP packets, which were ignored because the entry was invalid.
swL3OspfInternalLsdbTable
The OSPF Process's Link State Database.
swL3OspfInternalLsdbEntry
A single Link State Advertisement.
swL3OspfInternalLsdbAreaId
The 32 bit identifier of the Area from which the LSA was received.
swL3OspfInternalLsdbType
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
swL3OspfInternalLsdbLsid
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
swL3OspfInternalLsdbRouterId
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
swL3OspfInternalLsdbMetric
Enter the metric (1 - 65535; 0 for auto cost) of this area.
swL3OspfInternalLsdbSequenceNo
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
swL3OspfInternalLsdbAge
This field is the age of the link state adver- tisement in seconds.
swL3OspfInternalLsdbChecksum
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the sa ...
swL3OspfExternalLsdbTable
The OSPF Process's Links State Database.
swL3OspfExternalLsdbEntry
A single Link State Advertisement.
swL3OspfExternalLsdbType
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
swL3OspfExternalLsdbLsid
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
swL3OspfExternalLsdbRouterId
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
swL3OspfExternalLsdbMetric
Enter the metric (1 - 65535; 0 for auto cost) of this area.
swL3OspfExternalLsdbMetricType
Enter the metric type of this area.
swL3OspfExternalLsdbSequenceNo
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
swL3OspfExternalLsdbAge
This field is the age of the link state adver- tisement in seconds.
swL3OspfExternalLsdbChecksum
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the sa ...
swL3OspfExternalLsdbForwardingAddress
This field is the forwarding dddress.
swL3OspfExternalLsdbRouteTag
This field is the route tag.
swL3VrrpOperTable
Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'swL3vrrpOperEntry' items.
swL3VrrpOperEntry
An entry in the vrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID. Rows in the table cannot be modified unless the value of `swL3V ...
swL3VrrpOperIfIndex
The ifIndex value of the interface for which Vrrp is enabled.
swL3VrrpOperVrId
This object contains the Virtual Router Identifier (VRID).
swL3VrrpOperVirtualMacAddr
The virtual MAC address of the virtual router. Although this object can be derived from the 'swL3VrrpOperVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP traps.
swL3VrrpOperState
The current state of the virtual router. This object has three defined values: - `initialize', which indicates that all the virtual router is waiting for a startup event. - `backup', which indicates the virtual router is monitoring the availability of the ...
swL3VrrpOperAdminState
This object will enable/disable the virtual router function. Setting the value to `up', will transition the state of the virtual router from `initialize' to `backup' or `master', depending on the value of `swL3VrrpOperPriority'. Setting the value to `down ...
swL3VrrpOperPriority
This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participat ...
swL3VrrpOperMasterIpAddr
The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router.
swL3VrrpOperCriticalIpAddr
In the case where there is more than one IP address for a given `ifIndex', this object is used to specify the IP address that will become the `swL3VrrpOperMasterIpAddr', should the virtual router transition from backup to master. If this object is set to ...
swL3VrrpOperCheckCriticalIpState
Critical Ip state.
swL3VrrpOperAuthType
Authentication type used for VRRP protocol exchanges between virtual routers. This value of this object is the same for a given ifIndex. New enumerations to this list can only be added via a new RFC on the standards track.
swL3VrrpOperAuthKey
The Authentication Key. This object is set according to the value of the 'swL3VrrpOperAuthType' object ('simpleTextPassword' or 'ipAuthenticationHeader'). If the length of the value is less than 16 octets, the agent will left adjust and zero fill to 16 oc ...
swL3VrrpOperAdvertisementInterval
The time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements.
swL3VrrpOperPreemptMode
Controls whether a higher priority virtual router will preempt a lower priority master.
swL3VrrpOperVirtualRouterUpTime
This is the value of the `sysUpTime' object when this virtual router (i.e., the `swL3VrrpOperState') transitioned out of `initialized'.
swL3VrrpOperVirtualIpAddr
The assigned IP addresses that a virtual router is responsible for backing up.
swL3VrrpOperRowStatus
The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the vrrpOperTable is constrained by the operational state of the corresponding virtual router. When `vrrpOp ...

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list