DES3650-SWL3MGMT-MIB Download

swL3DevCtrlRIPState

This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled.

swL3DevCtrlOSPFState

This object indicates OSPF protocol is enabled or disabled.

swL3DevCtrlDVMRPState

This object indicates DVMRP protocol is enabled or disabled.

swL3DevCtrlVRRPState

This object indicates VRRP protocol is enabled or disabled.

swL3DevCtrlVrrpPingState

This object indicates VRRP protocol Ping is enabled or disabled.

swL3DevCtrlDHCPAutoConfigState

This object indicates auto config is enabled or disabled.

swL3IpCtrlEntry

A list of information about a specific IP interface.

swL3IpCtrlInterfaceName

This object indicates the name of the IP interface.

swL3IpCtrlIfIndex

This object uniquely identifies the IP interface number in the swL3IpCtrlTable.

swL3IpCtrlIpAddr

The IP address of the interface. This object only can take the value of the unicast IP address.

swL3IpCtrlIpSubnetMask

The IP net mask for this interface.

swL3IpCtrlVlanName

This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.

swL3IpCtrlProxyArp

-- "This object indicates enable/disable of the proxy ARP function for IPv4. When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.

swL3IpCtrlMode

This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. ...

swL3IpCtrlAdminState

The state of the IP interface.

swL3IpCtrlIpv4AdminState

-- "The IPv4 admin state of the IP interface. The default state is determined by project. -- This state will only be effective when the swL3IpCtrlAdminState is enabled. -- "The current IPv4 operational state of the IP int ...

swL3IpCtrlIpv6LinkLocalPrefixLen

The IPv6 prefix length for this IPv6 link local address.

swL3IpCtrlState

This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.

swL3IpCtrlIpv6LinkLocalAutoState

The state of the IPv6 link local auto.

swL3IpCtrlProxyArpLocalState

-- "If the state is enabled, the switch will be allowed to respond to the proxy ARP -- when the source IP and destination IP are in the same interface. This table contains IPv6 information of an IP interface.

swL3Ipv6CtrlEntry

A list of IPv6 information about a specific IP interface.

swL3Ipv6CtrlInterfaceName

This object indicates the name of the IP interface.

swL3Ipv6CtrlMaxReassmblySize

Maximum Reassembly Size of the IP interface.

swL3Ipv6CtrlNsRetransTimer

Neighbor solicitation's retransmit timer. The unit is set in milliseconds.

swL3Ipv6CtrlRaMinRtrAdvInterval

The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval

swL3Ipv6CtrlRaMaxRtrAdvInterval

The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.

swL3Ipv6CtrlRaLifeTime

Indicates the lifetime of the router as the default router.

swL3Ipv6CtrlRaReachableTime

Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.

swL3Ipv6CtrlRaRetransTime

Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.

swL3Ipv6CtrlRaHopLimit

Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.

swL3Ipv6CtrlRaManagedFlag

When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.

swL3Ipv6CtrlRaOtherConfigFlag

When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.

swL3Ipv6AddressCtrlTable

This table contain IPv6 address information for each IP interface.

swL3Ipv6AddressCtrlEntry

A list of information about a specific IPv6 address.

swL3Ipv6AddressCtrlInterfaceName

This object indicates the name of the IP interface.

swL3Ipv6Address

Specify the IPv6 address.

swL3Ipv6AddressCtrlPrefixLen

Indicates the prefix length of this IPv6 address.

swL3Ipv6AddressCtrlPreferredLifeTime

Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.

swL3Ipv6AddressCtrlValidLifeTime

Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.

swL3Ipv6AddressCtrlOnLinkFlag

When enabled, the address implied by the specified prefix is available on the link where the RA message is received.

swL3Ipv6AddressCtrlAutonomousFlag

When enabled, the specified prefix will be used to create an autonomous address configuration.

swL3Ipv6AddressCtrlState

This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.

swL3IpCtrlAllIpIfState

This object indicates all interface function state of the device.

swL3IpFdbInfoTable

A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.

swL3IpFdbInfoEntry

Information about a specific IP address for which the bridge has some forwarding and/or filtering information.

swL3IpFdbInfoIpSubnetMask

A IP net mask for this interface.for which switch has forwarding and/or filtering information.

swL3IpFdbInfoPort

Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that swi ...

swL3IpFdbInfoType

The status of this entry.

swL3IpStaticRouteTable

This entity's IP static Routing table.

swL3IpStaticRouteEntry

A particular route to a particular destination, under a particular policy. Once an entry is built,it shouldn't be modified.That is,it just supports create and delete actions.

swL3IpStaticRouteDest

The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the v ...

swL3IpStaticRouteMask

Indicate the mask to be logical-AND with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpS ...

swL3IpStaticRouteBkupState

The routing state for this route.The value SHOULD be primary(1), backup(2) or none(3).

swL3IpStaticRouteNextHop

Specifies the IP address for the next hop router. An IP address of 255.255.255.255 denotes a Null interface as the next hop.

swL3IpStaticRouteMetric

Specifies the routing metric for this route.

swL3IpStaticRouteStatus

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresp ...

swL3IpStaticRouteWeight

Specifies the weight value. Used for the weighted multipath.

swL3IpStaticRouteInterfaceName

Specifies the name of the IP interface.

swL3RelayDhcpState

This object indicates Dhcp Relay function is enabled or disabled.

swL3RelayDhcpHopCount

This object indicates the maximum number of router hops that the BOOTP packets can cross.

swL3RelayDhcpTimeThreshold

This object indicates the minimum time in seconds within which the switch must relay the Dhcp request. If this time is exceeded, the switch will drop the Dhcp packet.

swL3RelayDhcpCtrlTable

This table specifys the IP address as a destination to forward (relay) DHCP packets to.

swL3RelayDhcpCtrlEntry

A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.

swL3RelayDhcpCtrlInterfaceName

The name of the IP interface.

swL3RelayDhcpCtrlServer

The DHCP server IP address.

swL3RelayDhcpCtrlState

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresp ...

swL3RelayDhcpOption82State

This object indicates DHCP Relay Option 82 function is enabled or disabled.

swL3RelayDhcpOption82CheckState

This object indicates DHCP Relay Option 82 Check function is enabled or disabled.

swL3RelayDhcpOption82Policy

This object indicates DHCP Relay Option 82 Policy.

swL3RelayDnsState

This object indicates DNS Relay function is enabled or disabled.

swL3RelayDnsPrimaryServer

This object indicates the address of the primary DNS server.

swL3RelayDnsSecondaryServer

This object indicates the address of the secondary DNS server.

swL3RelayDnsCacheState

This object indicates DNS Relay cache is enabled or disabled.

swL3RelayDnsStaticTableState

This object indicates DNS Relay static table is enabled or disabled.

swL3RelayDnsCtrlTable

This table display the current DNS relay static table.

swL3RelayDnsCtrlEntry

A list of information display the current DNS relay static table.

swL3RelayDnsCtrlDomainName

The domain name of the entry.

swL3RelayDnsCtrlIpAddr

The IP address of the entry.

swL3RelayDnsCtrlState

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresp ...

swL3Md5Table

This table display the current MD5 key table.

swL3Md5Entry

A list of information display the current MD5 key table.

swL3Md5KeyId

The MD5 key ID.

swL3Md5Key

An MD5 password of up to 16 bytes.

swL3Md5RowStatus

This object indicates the status of this entry.

swL3RouteRedistriTable

Route redistribution allows routers on the network. That are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the vairous router¡¦s routing tables and assinging appropriate metrics ...

swL3RouteRedistriEntry

A list of information display the route redistribution table.

swL3RouteRedistriSrcProtocol

Allows the selection of the protocol of the source device.

swL3RouteRedistriDstProtocol

Allows the selection of the protocol of the destination device.

swL3RouteRedistriType

Allows the selection of one of the methods for calcalculating the metric value.

swL3RouteRedistriMetric

Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.

swL3RouteRedistriRowStatus

This object indicates the status of this entry.

swL3OspfHostTable

The list of Hosts, and their metrics, that the router will advertise as host routes.

swL3OspfHostEntry

A metric to be advertised, for a given type of service, when a given host is reachable.

swL3OspfHostIpAddress

The IP Address of the Host.

swL3OspfHostTOS

The Type of Service of the route being configured.

swL3OspfHostMetric

The Metric to be advertised.

swL3OspfHostAreaID

The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0

swL3OspfHostStatus

This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.

swL3ospfVirtIfTable

Information about this router's virtual inter- faces.

swL3ospfVirtIfEntry

Information about a single Virtual Interface.

swL3ospfVirtIfAreaId

The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0

swL3ospfVirtIfNeighbor

The Router ID of the Virtual Neighbor.

swL3ospfVirtIfTransitDelay

The estimated number of seconds it takes to transmit a link- state update packet over this interface.

swL3ospfVirtIfRetransInterval

The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should b ...

swL3ospfVirtIfHelloInterval

The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.

swL3ospfVirtIfRtrDeadInterval

The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor.

swL3ospfVirtIfState

OSPF virtual interface states.

swL3ospfVirtIfEvents

The number of state changes or error events on this Virtual Link

swL3ospfVirtIfAuthType

The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.

swL3ospfVirtIfAuthKey

If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Lar ...

swL3ospfVirtIfAuthKeyID

The MD5 key ID.

swL3ospfVirtIfStatus

This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.

swL3ospfIfTable

The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF.

swL3ospfIfEntry

The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF.

swL3ospfIfIpAddress

The IP address of this OSPF interface.

swL3ospfAddressLessIf

For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.

swL3ospfIfAreaId

A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.

swL3ospfIfType

The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', a ...

swL3ospfIfAdminStat

The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.

swL3ospfIfRtrPriority

The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular netw ...

swL3ospfIfTransitDelay

The estimated number of seconds it takes to transmit a link state update packet over this interface.

swL3ospfIfRetransInterval

The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.

swL3ospfIfHelloInterval

The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.

swL3ospfIfRtrDeadInterval

The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common netw ...

swL3ospfIfPollInterval

The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.

swL3ospfIfState

The OSPF Interface State.

swL3ospfIfDesignatedRouter

The IP Address of the Designated Router.

swL3ospfIfBackupDesignatedRouter

The IP Address of the Backup Designated Router.

swL3ospfIfEvents

The number of times this OSPF interface has changed its state, or an error has occurred.

swL3ospfIfMulticastForwarding

The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMult ...

swL3ospfIfDemand

Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.

swL3ospfIfAuthType

The authentication type specified for an in- terface. Additional authentication types may be assigned locally.

swL3ospfIfAuthKey

The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and s ...

swL3ospfIfAuthKeyID

The MD5 key ID.

swL3ospfIfPassiveMode

Assign the designated entry to be a passive interface.

swL3ospfIfStatus

-- "This variable displays the status of the en- -- try. Setting it to 'invalid' has the effect of -- rendering it inoperative. The internal effect -- (row removal) is implementation dependent. The Metric to be ...

swL3RoutePreferenceRIP

Used to configure the route preference of RIP.

swL3RoutePreferenceOSPFIntra

Used to configure the route preference of OSPF Intra.

swL3RoutePreferenceStatic

Used to configure the route preference of Static.

swL3RoutePreferenceLocal

Used to read the route preference of Local.

swL3RoutePreferenceOSPFInter

Used to configure the route preference of OSPF Inter.

swL3RoutePreferenceOSPFExtT1

Used to configure the route preference of OSPFExtT1.

swL3RoutePreferenceOSPFExtT2

Used to configure the route preference of OSPF ExtT2.

swL3ospfAreaTable

Information describing the configured parame- ters and cumulative statistics of the router's attached areas.

swL3ospfAreaEntry

Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas.

swL3ospfAreaId

A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.

swL3ospfAreaType

The type specified for an area.

swL3ospfAreaSummaryState

Whether the summary LSA is effective for this area.

swL3ospfAreaMetric

Enter the metric (1 - 65535; 0 for auto cost) of this area.

swL3ospfAreaTranslateState

.

swL3ospfAreaStatus

This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.

swL3dvmrpInterfaceTable

The (conceptual) table listing the router's multicast- capable interfaces.

swL3dvmrpInterfaceEntry

An entry (conceptual row) in the dvmrpInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides.

swL3dvmrpInterfaceIfIndex

The ifIndex value of the interface for which DVMRP is enabled.

swL3dvmrpInterfaceLocalAddress

The IP address this system will use as a source address on this interface. On unnumbered interfaces, it must be the same value as dvmrpInterfaceLocalAddress for some interface on the system.

swL3dvmrpInterfaceMetric

The distance metric for this interface which is used to calculate distance vectors.

swL3dvmrpInterfaceProbe

the period of sending probe

swL3dvmrpInterfaceNbrTimeout

the timer when neighbor expired.

swL3dvmrpInterfaceStatus

The status of this entry. Creating the entry enables DVMRP on the virtual interface; destroying the entry or setting it to notInService disables DVMRP on the virtual interface.

swL3dvmrpInterfaceRcvBadPkts

The number of DVMRP packets received on the interface by the DVMRP process which were subsequently discarded as invalid (e.g. invalid packet format, or a route report from an unknown neighbor).

swL3dvmrpInterfaceRcvBadRoutes

The number of routes, in valid DVMRP packets, which were ignored because the entry was invalid.

swL3OspfInternalLsdbTable

The OSPF Process's Link State Database.

swL3OspfInternalLsdbEntry

A single Link State Advertisement.

swL3OspfInternalLsdbAreaId

The 32 bit identifier of the Area from which the LSA was received.

swL3OspfInternalLsdbType

The type of the link state advertisement. Each link state type has a separate advertise- ment format.

swL3OspfInternalLsdbLsid

The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.

swL3OspfInternalLsdbRouterId

The 32 bit number that uniquely identifies the originating router in the Autonomous System.

swL3OspfInternalLsdbMetric

Enter the metric (1 - 65535; 0 for auto cost) of this area.

swL3OspfInternalLsdbSequenceNo

The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.

swL3OspfInternalLsdbAge

This field is the age of the link state adver- tisement in seconds.

swL3OspfInternalLsdbChecksum

This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the sa ...

swL3OspfExternalLsdbTable

The OSPF Process's Links State Database.

swL3OspfExternalLsdbEntry

A single Link State Advertisement.

swL3OspfExternalLsdbType

The type of the link state advertisement. Each link state type has a separate advertise- ment format.

swL3OspfExternalLsdbLsid

The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.

swL3OspfExternalLsdbRouterId

The 32 bit number that uniquely identifies the originating router in the Autonomous System.

swL3OspfExternalLsdbMetric

Enter the metric (1 - 65535; 0 for auto cost) of this area.

swL3OspfExternalLsdbMetricType

Enter the metric type of this area.

swL3OspfExternalLsdbSequenceNo

The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.

swL3OspfExternalLsdbAge

This field is the age of the link state adver- tisement in seconds.

swL3OspfExternalLsdbChecksum

This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the sa ...

swL3OspfExternalLsdbForwardingAddress

This field is the forwarding dddress.

swL3OspfExternalLsdbRouteTag

This field is the route tag.

swL3VrrpOperTable

Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'swL3vrrpOperEntry' items.

swL3VrrpOperEntry

An entry in the vrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID. Rows in the table cannot be modified unless the value of `swL3V ...

swL3VrrpOperIfIndex

The ifIndex value of the interface for which Vrrp is enabled.

swL3VrrpOperVrId

This object contains the Virtual Router Identifier (VRID).

swL3VrrpOperVirtualMacAddr

The virtual MAC address of the virtual router. Although this object can be derived from the 'swL3VrrpOperVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP traps.

swL3VrrpOperState

The current state of the virtual router. This object has three defined values: - `initialize', which indicates that all the virtual router is waiting for a startup event. - `backup', which indicates the virtual router is monitoring the availability of the ...

swL3VrrpOperAdminState

This object will enable/disable the virtual router function. Setting the value to `up', will transition the state of the virtual router from `initialize' to `backup' or `master', depending on the value of `swL3VrrpOperPriority'. Setting the value to `down ...

swL3VrrpOperPriority

This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participat ...

swL3VrrpOperMasterIpAddr

The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router.

swL3VrrpOperCriticalIpAddr

In the case where there is more than one IP address for a given `ifIndex', this object is used to specify the IP address that will become the `swL3VrrpOperMasterIpAddr', should the virtual router transition from backup to master. If this object is set to ...

swL3VrrpOperCheckCriticalIpState

Critical Ip state.

swL3VrrpOperAuthType

Authentication type used for VRRP protocol exchanges between virtual routers. This value of this object is the same for a given ifIndex. New enumerations to this list can only be added via a new RFC on the standards track.

swL3VrrpOperAuthKey

The Authentication Key. This object is set according to the value of the 'swL3VrrpOperAuthType' object ('simpleTextPassword' or 'ipAuthenticationHeader'). If the length of the value is less than 16 octets, the agent will left adjust and zero fill to 16 oc ...

swL3VrrpOperAdvertisementInterval

The time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements.

swL3VrrpOperPreemptMode

Controls whether a higher priority virtual router will preempt a lower priority master.

swL3VrrpOperVirtualRouterUpTime

This is the value of the `sysUpTime' object when this virtual router (i.e., the `swL3VrrpOperState') transitioned out of `initialized'.

swL3VrrpOperVirtualIpAddr

The assigned IP addresses that a virtual router is responsible for backing up.

swL3VrrpOperRowStatus

The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the vrrpOperTable is constrained by the operational state of the corresponding virtual router. When `vrrpOp ...