DGS3200-L2MGMT-MIB Download

swDevInfoTotalNumOfPort

The number of ports within this switch. This value is the sum of the ports within this switch.

swDevInfoNumOfPortInUse

The number of ports in this switch connected to the segment or the end stations.

swDevInfoFrontPanelLedStatus

This object is a set of system LED indications. The first four octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fi ...

swL2DevCtrlStpState

This object can enable or disable the spanning tree algorithm during the runtime of the system.

swL2DevCtrlIGMPSnooping

This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.

swL2DevCtrlIGMPSnoopingMcstRTOnly

-- "This object indicates IGMP snooping forward multicast routing only state. This object can enable or disable RMON.

swL2DevCtrlSnmpTrapState

This object controls the SNMP trap status.

swL2DevCtrlCleanAllStatisticCounter

When the object is set to active, all statistical counters will be cleared. If set to normal, no action.

swL2DevCtrlVlanIdOfFDBTbl

Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.

swL2MACNotifyState

This object can enable or disable MAC Notification.

swL2MACNotifyHistorySize

This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .

swL2MACNotifyInterval

This object indicates the time interval, in seconds, which will trigger MAC notification messages.

swL2DevCtrlTelnetState

This object controls the Telnet status.

swL2DevCtrlTelnetTcpPort

This object designates TCP ports. When Telnet is disabled, this object is not accessible.

swL2DevCtrlManagementVlanId

This object controls which previously created VLANs are included in the System IP Interface.

swL2DevCtrlWebState

This object controls the Web status.

swL2DevCtrlWebTcpPort

This object designates TCP ports. When Web is disabled, this object is not accessible.

swL2DevCtrlIpAutoconfig

This object controls the IP auto configuration state.

swL2DevAlarmNewRoot

When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.

swL2DevAlarmTopologyChange

This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwardin ...

swL2DevAlarmLinkChange

This object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is di ...

swL2VlanStaticTable

A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

swL2VlanStaticEntry

Static information for a VLAN configured into the device by (local or network) management.

swL2VlanIndex

The VLAN-ID or other identifier referring to this VLAN.

swL2VLANAdvertisement

This object indicates if the advertisement is active or not.

swL2PVIDAutoAssignmentState

This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change PVID. If 'Auto-assign PVID' is enabled, PVID ...

swL2PortInfoTable

A table that contains information about every port.

swL2PortInfoEntry

A list of information for each port of the device.

swL2PortInfoPortIndex

This object indicates the module's port number.(1..Max port number in the module)

swL2PortInfoMediumType

Indicates medium type of the port number.

swL2PortInfoUnitID

Indicates ID of the unit in the system

swL2PortInfoType

This object indicates the connector type of this port.

swL2PortInfoLinkStatus

This object indicates the port link status.

swL2PortInfoNwayStatus

This object indicates the port speed and duplex mode.

swL2PortCtrlTable

A table that contains control information about every port.

swL2PortCtrlEntry

A list of control information for each port of the device.

swL2PortCtrlPortIndex

This object indicates the module's port number.(1..Max port number in the module)

swL2PortCtrlMediumType

Indicates medium type of the port number.

swL2PortCtrlUnitIndex

Indicates ID of the unit in the device

swL2PortCtrlAdminState

This object decides if the port is enabled or disabled.

swL2PortCtrlNwayState

Chose the port speed, duplex mode, and N-Way function mode.

swL2PortCtrlFlowCtrlState

The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.

swL2PortCtrlLearningState

This object decides if the port is locked or not.

swL2PortCtrlMACNotifyState

This object sets each port's MAC notification state.

swL2PortCtrlMulticastfilter

-- "This object controls the multicast port filtering mode for a specified port. This object configures the switch's jumbo frame settings.

swL2PortCtrlJumboFrameMaxSize

This object describes how many bytes the max jumbo frame is.

swL2PortCounterCtrlEntry

A list of entry used to clear counter information for each port of the device.

swL2PortCounterCtrlPortIndex

This object indicates the module's port number.(1..Max port number in the module)

swL2PortCounterClearCtrl

This object indicates if to clear the counters for each port of the device or not.

swL2PortErrTable

A table that contains error information for each port.

swL2PortErrEntry

A list of information regarding port errors on the device.

swL2PortErrPortIndex

This object indicates the module's port number.(1..Max port number in the module).

swL2PortErrPortState

This object indicates the port state is enabled or disabled.

swL2PortErrPortConnStatus

This object indicates whether the PortStatus is err-disabled or not.

swL2PortErrPortReason

This object describes if the reason for the port error is STP LBD or Storm control.

swL2QOSBandwidthControlEntry

A list of information contained in the swL2QOSBandwidthControlTable.

swL2QOSBandwidthPortIndex

Indicates the port .

swL2QOSBandwidthRxRate

Indicates RX Rate(64Kbit/sec) of the specified port. Value 1024001 means no limit.

swL2QOSBandwidthTxRate

Indicates TX Rate(64Kbit/sec) of the specified port. Value 1024001 means no limit.

swL2QOSBandwidthRadiusRxRate

The RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.

swL2QOSBandwidthRadiusTxRate

The TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.

swL2QOSSchedulingTable

.

swL2QOSSchedulingEntry

A list of information contained in the swL2QOSSchedulingTable.

swL2QOSSchedulingClassIndex

Indicates the hardware queue number.

swL2QOSSchedulingMaxPkts

Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.

swL2QOSSchedulingMechanism

Indicates the mechanism of QoS scheduling.

swL2QOS8021pUserPriorityEntry

A list of information contained in the swL2QOS8021pUserPriorityTable.

swL2QOS8021pUserPriorityIndex

The 802.1p user priority .

swL2QOS8021pUserPriorityClass

The number of the switch's hardware priority queue. The switch has seven hardware priority queues available. They are numbered between 0 (the lowest priority) and 6 (the highest priority).

swL2QOS8021pDefaultPriorityTable

.

swL2QOS8021pDefaultPriorityEntry

A list of information contained in the swL2QOS8021pDefaultPriorityTable.

swL2QOS8021pDefaultPriorityIndex

Indicates the port number .

swL2QOS8021pDefaultPriority

The priority value to assign to untagged packets received by the switch ports on the switch..

swL2QOS8021pRadiusPriority

The value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.

swL2QOSSchedulingMechanismCtrl

This object controls QoS scheduling Mechanism.

swL2QOSHolPreventionCtrl

-- "Controls QoS HoL Prevention A port security feature which controls the address leaning capability and traffic forwarding decisions. Each port can be enabled or disabled for this function. When it is enabled and a number is given said N, which a ...

swL2PortSecurityControlEntry

A list of information contained in the swL2PortSecurityControlTable.

swL2PortSecurityPortIndex

Indicates the secured port to lock address learning.

swL2PortSecurityMaxLernAddr

Indicates allowable number of addresses to be learned on this port.

swL2PortSecurityMode

Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be ...

swL2PortSecurityAdmState

Indicates administration state of locking address.

swL2PortSecurityEntryClearCtrl

Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.

swL2PortSecurityDelVlanName

Indicates VLAN name.

swL2PortSecurityDelPort

Indicates the port.

swL2PortSecurityDelMacAddress

Specifies a MAC address.

swL2PortSecurityDelActivity

.

swL2PortSecurityTrapLogState

When enabled(2),whenever there's a new MAC address that violates the pre-defined port security configuration, traps will be sent out and the relevant information will be logged into the system.

swL2DhcpRelayState

This object indicates if the DHCP relay function is enabled or disabled.

swL2DhcpRelayHopCount

This object indicates the maximum number of router hops that DHCP packets can cross.

swL2DhcpRelayTimeThreshold

This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.

swL2DhcpRelayOption82State

This object indicates if the DHCP relay agent information option 82 function is enabled or disabled.

swL2DhcpRelayOption82Check

This object indicates if the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.

swL2DhcpRelayOption82Policy

This object indicates the reforwarding policy of DHCP relay agent information option 82. replace(1) - replace the exiting option 82 field in messages. drop(2) - discard messages with existing option 82 field. keep(3) - retain the existing option ...

swL2DhcpRelayCtrlTable

This table specifies the IP address as a destination to forward (relay) DHCP packets to.

swL2DhcpRelayCtrlEntry

A list of information that specifies the IP address as a destination to forward (relay) DHCP packets to.

swL2DhcpRelayCtrlInterfaceName

The name of the IP interface.

swL2DhcpRelayCtrlServer

The DHCP server IP address.

swL2DhcpRelayCtrlState

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresp ...

swL2TrunkMaxSupportedEntries

Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).

swL2TrunkCurrentNumEntries

Current active number of entries in the trunk configuration table.

swL2TrunkCtrlTable

This table specifies which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkCtrlEntry

A list of information that specifies which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkIndex

The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.

swL2TrunkName

The name of logical port trunk group.

swL2TrunkMasterPort

The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled ...

swL2TrunkMember

Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.

swL2TrunkFloodingPort

-- "The object indicates the flooding port number of the port trunk -- entry. The first port of the Trunk group is implicitly configured to -- be the flooding port. This object indicates the type of trunk group. static : i ...

swL2TrunkState

This object indicates the status of this entry.

swL2TrunkAlgorithm

This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.

swL2TrunkLACPPortTable

This table specifies which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkLACPPortEntry

A list of information specifies which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkLACPPortIndex

The index of logical port LACP.

swL2TrunkLACPPortState

The state of logical port LACP.

swL2MirrorLogicTargetPort

This object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.

swL2MirrorPortSourceIngress

This represents the port where ingress packets will be sniffed.

swL2MirrorPortSourceEgress

This represents the port where egress packets will be sniffed.

swL2MirrorPortState

This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the correspon ...

swL2IGMPMaxSupportedVlans

Maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).

swL2IGMPMaxIpGroupNumPerVlan

Maximum number of multicast IP groups per VLAN in the layer 2 IGMP information table(swL2IGMPQueryInfoTable).

swL2IGMPCtrlEntry

The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.

swL2IGMPQueryInterval

The frequency at which IGMP Host-Query packets are transmitted on this switch.

swL2IGMPMaxResponseTime

The maximum query response time on this switch.

swL2IGMPRobustness

The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.

swL2IGMPLastMemberQueryInterval

The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.

swL2IGMPHostTimeout

The timer value for sending IGMP query packets when none were sent by the host on the LAN. The timer works on a per-VLAN basis. Our device will be activated to send the query messages if the timer expires. Please reference RFC2236-1997.

swL2IGMPRouteTimeout

The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.

swL2IGMPLeaveTimer

When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.

swL2IGMPQueryState

This object decides if the IGMP query is enabled or disabled.

swL2IGMPCurrentState

This object indicates the current IGMP query state.

swL2IGMPCtrlState

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP function is disabled for this entry. enable(3) - ...

swL2IGMPFastLeaveState

This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP fast-leave function is disabled for th ...

swL2IGMPQueryInfoTable

The table contains the number current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device.

swL2IGMPQueryInfoEntry

Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of the associated VLAN entry are all enabled.

swL2IGMPInfoQueryCount

This object indicates the number of query packets received since the IGMP function was enabled, on a per-VLAN basis.

swL2IGMPInfoTxQueryCount

This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.

swL2IGMPInfoTable

The table containing current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of the associated VLAN entries are all enabled. Note that the priority of IGMP table entries is lower than the Fil ...

swL2IGMPInfoEntry

Information about current IGMP information which was captured by this device, provided that the swL2DevCtrlIGMPSnooping and the swL2IGMPCtrlState of associated VLAN entries are all enabled.

swL2IGMPVid

This object indicates the VID of individual IGMP table entries. It shows the VID IGMP report information captured on the network.

swL2IGMPGroupIpAddr

This object identifies group IP addresses which were captured from IGMP packets, on a per-VLAN basis.

swL2IGMPMacAddr

This object identifies MAC addresses which correspond to the swL2IGMPGroupIpAddr, on per-VLAN basis.

swL2IGMPPortMap

This object indicates which ports belong to the same multicast group, on a per-VLAN basis. Each multicast group has an octet string which is indicated by a port map. The most significant bit represents the lowest numbered port, and the least significant b ...

swL2IGMPIpGroupReportCount

This object indicates how many report packets were receive by our device, that correspond with this entry when the IGMP function is enabled on per-VLAN basis.

swL2IGMPRouterPortTable

The information of the router port table.

swL2IGMPRouterPortEntry

The entry of swL2IGMPRouterPortTable.

swL2IGMPRouterPortVlanid

This object indicates the VLAN ID of the router port entry.

swL2IGMPRouterPortVlanName

This object indicates the VLAN name of the router port entry.

swL2IGMPRouterPortStaticPortList

This object indicates the static portlist of the router port entry.

swL2IGMPRouterPortDynamicPortList

This object indicates the dynamic portlist of the router port entry.

swL2IGMPRouterPortForbiddenPortList

This object indicates the forbidden portlist of the router port entry.

swL2IGMPMulticastVlanTable

-- "The information of the IGMP snooping multicast VLAN table. -- "The entry of swL2IGMPMulticastVlanTable. -- "This object indicates the VLAN ID of the IGMP snooping multicast -- VLAN entry. -- "Thi ...

swL2TrafficSegEntry

A list of information which specifies the port with its traffic forwarding list.

swL2TrafficSegPort

The port number of the logical port.

swL2TrafficSegForwardPorts

The port list to which the specific port can forward traffic.

swL2MulticastFilterModeVlanTable

A table that contains information about VLAN multicast filter mode.

swL2MulticastFilterModeVlanEntry

A list of multicast filter mode information for each VLAN.

swL2MulticastFilterVid

Indicates VID for each VLAN.

swL2MulticastFilterVlanMode

Specifies multicast filter mode for each VLAN.

swL2LoopDetectInterval

This object indicates the interval value, the range is from 1 to 32767 seconds.

swL2LoopDetectRecoverTime

This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.

swL2LoopDetectMode

This object indicates the loopback detection mode for the system.

swL2LoopDetectPortTable

The table specifies the loopback detection function specified by port.

swL2LoopDetectPortEntry

The table specifies the loopback detection function specified by port.

swL2LoopDetectPortIndex

This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module

swL2LoopDetectPortState

This object indicates the loopback detection function state on the port.

swL2LoopDetectPortLoopVLAN

This object indicates the VLAN list that has detected a loopback.

swL2LoopDetectPortLoopStatus

This object indicates the port status.

swL2macNotifyInfo

This object indicates the last time reboot information.

swL2PortSecurityViolationMac

This object indicates the MAC address that violates the port security configuration.