DOT12-IF-MIB Download

dot12ConfigTable

Configuration information for a collection of 802.12 interfaces attached to a particular system.

dot12ConfigEntry

Configuration for a particular interface to an 802.12 medium.

dot12CurrentFramingType

When dot12DesiredFramingType is one of 'frameType88023' or 'frameType88025', this is the type of framing asserted by the interface. When dot12DesiredFramingType is 'frameTypeEither', dot12CurrentFramingType shall be one of 'frameType88023' or 'frameType88 ...

dot12DesiredFramingType

The type of framing which will be requested by the interface during the next interface MAC initialization or open action. In master mode, this is the framing mode which will be granted by the interface. Note that for a master mode interface, this object ...

dot12FramingCapability

The type of framing this interface is capable of supporting.

dot12DesiredPromiscStatus

This object is used to select the promiscuous mode that this interface will request in the next training packet issued on this interface. Whether the repeater grants the requested mode must be verified by examining the state of the PP bits in the correspo ...

dot12TrainingVersion

The value that will be used in the version bits (vvv bits) in training frames on this interface. This is the highest version number supported by this MAC.

dot12LastTrainingConfig

This 16 bit field contains the configuration bits from the most recent error-free training frame received during training on this interface. Training request frames are received when in master mode, while training response frames are received in slave mod ...

dot12Commands

If the current value of dot12Status is 'closed', setting the value of this object to 'open' will change the corresponding instance of MIB-II's ifAdminStatus to 'up', cause this interface to enter the 'opening' state, and will cause training to be initiate ...

dot12Status

The current interface status with respect to training. One of the following values: opened - Training has completed successfully. closed - MAC has been disabled by setting dot12Commands to 'close'. opening - MAC is in training. Training si ...

dot12ControlMode

This object is used to configure and report whether or not this interface is operating in master mode. In a Demand Priority network, end node interfaces typically operate in slave mode, while switch interfaces may control the Demand Priority protocol and ...

dot12StatTable

Statistics for a collection of 802.12 interfaces attached to a particular system.

dot12StatEntry

Statistics for a particular interface to an 802.12 medium. The receive statistics in this table apply only to packets received by this station (i.e., packets whose destination address is either the local station address, the broadcast address, or a multi ...

dot12InHighPriorityFrames

This object is a count of high priority frames that have been received on this interface. Includes both good and bad high priority frames, as well as high priority training frames. Does not include normal priority frames which were priority promoted.

dot12InHighPriorityOctets

This object is a count of the number of octets contained in high priority frames that have been received on this interface. This counter is incremented by OctetCount for each frame received on this interface which is counted by dot12InHighPriorityFrames. ...

dot12InNormPriorityFrames

This object is a count of normal priority frames that have been received on this interface. Includes both good and bad normal priority frames, as well as normal priority training frames and normal priority frames which were priority promoted.

dot12InNormPriorityOctets

This object is a count of the number of octets contained in normal priority frames that have been received on this interface. This counter is incremented by OctetCount for each frame received on this interface which is counted by dot12InNormPriorityFrames ...

dot12InIPMErrors

This object is a count of the number of frames that have been received on this interface with an invalid packet marker and no PMI errors. A repeater will write an invalid packet marker to the end of a frame containing errors as it is forwarded through th ...

dot12InOversizeFrameErrors

This object is a count of oversize frames received on this interface. This counter is incremented by one for each frame received on his interface whose OctetCount is larger than the maximum legal frame size. The frame size which causes this counter to i ...

dot12InDataErrors

This object is a count of errored frames received on this interface. This counter is incremented by one for each frame received on this interface with any of the following errors: bad FCS (with no IPM), PMI errors (excluding frames with an IPM as the onl ...

dot12InNullAddressedFrames

This object is a count of null addressed frames received on this interface. This counter is incremented by one for each frame received on this interface with a destination MAC address consisting of all zero bits. Both void and training frames are includ ...

dot12OutHighPriorityFrames

This counter is incremented by one for each high priority frame successfully transmitted out this interface.

dot12OutHighPriorityOctets

This counter is incremented by OctetCount for each frame counted by dot12OutHighPriorityFrames. Note that this counter will roll over very quickly. It is provided for backward compatibility for Network Management protocols that do not support 64 bit coun ...

dot12TransitionIntoTrainings

This object is a count of the number of times this interface has entered the training state. This counter is incremented by one each time dot12Status transitions to 'linkFailure' from any state other than 'opening' or 'openFailure'.

dot12HCInHighPriorityOctets

This object is a count of the number of octets contained in high priority frames that have been received on this interface. This counter is incremented by OctetCount for each frame received on this interface which is counted by dot12InHighPriorityFrames. ...

dot12HCInNormPriorityOctets

This object is a count of the number of octets contained in normal priority frames that have been received on this interface. This counter is incremented by OctetCount for each frame received on this interface which is counted by dot12InNormPriorityFrames ...

dot12HCOutHighPriorityOctets

This counter is incremented by OctetCount for each frame counted by dot12OutHighPriorityFrames. This counter is a 64 bit version of dot12OutHighPriorityOctets. It should be used by Network Management protocols which support 64 bit counters (e.g. SNMPv2).

dot12ConfigGroup

A collection of objects for managing the status and configuration of IEEE 802.12 interfaces.

dot12StatsGroup

A collection of objects providing statistics for IEEE 802.12 interfaces.