Fibronics-EtherSwitch-MIB Download

fibEsFwVer

The firmware version in the form major.minor.

fibEsHwVer

The hardware version in the form major.minor.

fibEsIpAddr

The administrative value of the IP address. The current operational IP address can be obtained by the ipAdEntAddr entry in the ipAddrTable. This parameter will take effect only after a reset (fibEsReset) is issued or a power cycle.

fibEsNetMask

The administrative value of the subnet mask. The current operational subnet mask can be obtained by the ipAdEntNetMask entry in the ipAddrTable. This parameter will take effect only after a reset (fibEsReset) is issued or a power cycle.

fibEsDefaultGateway

The administrative value of the default gateway (router) IP address. The current operational default gateway's IP address can be obtained from the ipRouteTable. This parameter will take effect only after a reset (fibEsReset) is issued or a power cycle.

fibEsTrapRcvrMaxEnt

The maximum number of rows in the trap receiver table.

fibEsTrapRcvrCurEnt

The current number of rows in the trap receiver table.

fibEsTrapRcvrNext

The index of the next available row to be created in the trap receiver table. A value of zero means that the table is full and no more rows can be added.

fibEsTrapRcvrTable

A table of managers to which to send traps. Entries in the table are saved across resets and power cycles.

fibEsTrapRcvrEntry

Definition of rows in the trap receiver table. The column fibEsTrapRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with objects fibEsTrapRcvrStatus, fibEsTrapRcvrIpAddress, and fibEsTrapRcvrComm.

fibEsTrapRcvrIndex

The index of the row in the table.

fibEsTrapRcvrStatus

Setting this object to the value invalid(3) deletes the row from the table. The value invalid(3) should never be returned on a GET. The value of create(4) on a SET causes a new row to be created if the row does not already exist. If it does, then a 'ba ...

fibEsTrapRcvrIpAddress

IP address for an SNMP manager that is to receive the trap.

fibEsTrapRcvrComm

Community string to use.

fibEsNumPorts

The maximum number of ports on the switch.

fibEsNumStations

Aggregate number of currently active stations (nodes) on all ports on the switch. This is the value from the system module.

fibEsMostStations

Highest aggregate number of stations ever active on all ports at one time, since the last reset or power cycle. This is the value as seen by the system module.

fibEsMaxStations

Highest aggregate number of stations which the switch can support simultaneously. (This is the maximum number that the system module can support.)

fibEsReset

This object is used to reset the switch. Writing softReset(3) causes the switch to reset the hardware, run quick diagnostics, clear all counters, start switching, issue a warmstart trap, and then be able to respond to SNMP requests. Writing hardReset(4) ...

fibEsNumResets

Number of soft resets the switch has executed since the last hard reset or power cycle. Soft resets are defined as writing softReset(3) to fibEsReset, pressing the front panel reset button, executing a soft reset from the console, or resets induced by th ...

fibEsAddrAgingTime

Number of minutes of inactivity before an address entity is aged out. A value of zero means no aging. Note: if an address shows up on another port, the original port to address assignment is automatically deleted. The value is saved across resets and p ...

fibEsSysStaTable

A table of station addresses from all ports known to the system module.

fibEsSysStaEntry

Definition of the rows in the system module station address table. Rows can not be created or deleted via SNMP requests.

fibEsSysStaMacAddr

The Station's MAC address.

fibEsSysStaPort

The source port for the Station.

fibEsSysStaTraffic

A bit string that identifies with value of one of the ports that this station has generated traffic to or from. The bits are numbered starting at zero, with bit zero being the high order bit in the first byte, bit seven being the low order bit in the fir ...

fibEsPortTable

A table of information about each port. The number of rows is given by fibEsNumPorts.

fibEsPortEntry

Definition of rows in the port table. The number of rows is determined by the hardware and is specified by the value of fibEsNumPorts. Rows can not be created or deleted via SNMP requests.

fibEsPortIndex

A unique value for each port entry. The value corresponds the port number.

fibEsPortOprStatus

The operational status of the port. Setting to enabled(1) enables the port. Setting to disabled(2) disables the port. The value is saved across resets and power cycles.

fibEsPortDuplex

Indicates whether the port is jumper configured for full or half duplex operation. Note: internal connected ports are always halfDuplex(2).

fibEsPortRcvLocalFrames

Number of frames received where the destination is on this port.

fibEsPortForwardedFrames

Number of frames received on this port and forwarded to another port or the system module for processing.

fibEsPortMostStations

Highest number of stations ever active at any time since the last reset of the switch as seen by this port.

fibEsPortMaxStations

Maximum number of stations which the port can support simultaneously.

fibEsPortSWHandledFrames

Number of Frames received on this port and delivered to the system module for processing.

fibEsPortLocalStations

Number of stations on this port's address table which belong to the segment attached to this port.

fibEsPortRemoteStations

Number of stations on this port's address table which belong to segments attached to other ports.

fibEsPortUnknownStaFrames

Number of unicast frames received on this port and forwarded to the system module for processing because the source or destination station address is not in the port's forwarding table.

fibEsPortResetStats

Setting this object to reset(3) causes all traffic counters for this port to be set to zero. Also the value of fibEsPortResetTimer is set to zero.

fibEsPortResetTimer

Time (in 100th second ticks) since the port counters were reset.

fibEsPortResetAddrs

Setting this object to reset(3) clears all address table entries for this port as well as setting all port traffic counters to zero and setting fibEsPortResetTimer to zero.

fibEsPortRcvBcasts

Number of Broadcast Frames received on this port without errors.

fibEsPortSwitchedFrames

Number of frames switched on this port