INTEGRATED-SERVICES-MIB Download

extended

The MIB module to describe the Integrated Services Protocol

intSrvIfAttribTable

The reservable attributes of the system's in- terfaces.

intSrvIfAttribEntry

The reservable attributes of a given inter- face.

intSrvIfAttribAllocatedBits

The number of bits/second currently allocated to reserved sessions on the interface.

intSrvIfAttribMaxAllocatedBits

The maximum number of bits/second that may be allocated to reserved sessions on the inter- face.

intSrvIfAttribAllocatedBuffer

The amount of buffer space required to hold the simultaneous burst of all reserved flows on the interface.

intSrvIfAttribFlows

The number of reserved flows currently active on this interface. A flow can be created ei- ther from a reservation protocol (such as RSVP or ST-II) or via configuration information.

intSrvIfAttribPropagationDelay

The amount of propagation delay that this in- terface introduces in addition to that intro- diced by bit propagation delays.

intSrvIfAttribStatus

'active' on interfaces that are configured for RSVP.

intSrvFlowTable

Information describing the reserved flows us- ing the system's interfaces.

intSrvFlowEntry

Information describing the use of a given in- terface by a given flow. The counter intSrvFlowPoliced starts counting at the in- stallation of the flow.

intSrvFlowNumber

The number of this flow. This is for SNMP In- dexing purposes only and has no relation to any protocol value.

intSrvFlowType

The type of session (IP4, IP6, IP6 with flow information, etc).

intSrvFlowOwner

The process that installed this flow in the queue policy database.

intSrvFlowDestAddr

The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'ac- tive'.

intSrvFlowSenderAddr

The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'. This object may not be changed when the value of the RowStatus object is 'active'.

intSrvFlowDestAddrLength

The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'active'.

intSrvFlowSenderAddrLength

The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'active'.

intSrvFlowProtocol

The IP Protocol used by a session. This ob- ject may not be changed when the value of the RowStatus object is 'active'.

intSrvFlowDestPort

The UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by intSrvResvFwdProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A valu ...

intSrvFlowPort

The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by intSrvResvFwdProtocol is 50 (ESP) or 51 (AH), this represents a generalized port identifier (GPI). A valu ...

intSrvFlowFlowId

The flow ID that this sender is using, if this is an IPv6 session.

intSrvFlowInterface

The ifIndex value of the interface on which this reservation exists.

intSrvFlowIfAddr

The IP Address on the ifEntry on which this reservation exists. This is present primarily to support those interfaces which layer multi- ple IP Addresses on the interface.

intSrvFlowRate

The Reserved Rate of the sender's data stream. If this is a Controlled Load service flow, this rate is derived from the Tspec rate parameter (r). If this is a Guaranteed service flow, this rate is derived from the Rspec clearing rate parameter ( ...

intSrvFlowBurst

The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such ...

intSrvFlowWeight

The weight used to prioritize the traffic. Note that the interpretation of this object is implementation-specific, as implementations vary in their use of weighting procedures.

intSrvFlowQueue

The number of the queue used by this traffic. Note that the interpretation of this object is implementation-specific, as implementations vary in their use of queue identifiers.

intSrvFlowMinTU

The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.

intSrvFlowMaxTU

The maximum datagram size for this flow that will conform to the traffic specification. This value cannot exceed the MTU of the interface.

intSrvFlowBestEffort

The number of packets that were remanded to best effort service.

intSrvFlowPoliced

The number of packets policed since the incep- tion of the flow's service.

intSrvFlowDiscard

If 'true', the flow is to incur loss when traffic is policed. If 'false', policed traff- ic is treated as best effort traffic.

intSrvFlowService

The QoS service being applied to this flow.

intSrvFlowOrder

In the event of ambiguity, the order in which the classifier should make its comparisons. The row with intSrvFlowOrder=0 is tried first, and comparisons proceed in the order of in- creasing value. Non-serial implementations of the classifier s ...

intSrvFlowStatus

'active' for all active flows. This object may be used to install static classifier infor- mation, delete classifier information, or au- thorize such.

intSrvFlowNewIndex

This object is used to assign values to intSrvFlowNumber as described in 'Textual Con- ventions for SNMPv2'. The network manager reads the object, and then writes the value back in the SET that creates a new instance of intSrvFlowEntry. ...

intSrvIfAttribGroup

These objects are required for Systems sup- porting the Integrated Services Architecture.

intSrvFlowsGroup

These objects are required for Systems sup- porting the Integrated Services Architecture.