JUNIPER-ANALYZER-MIB Download

jnxAnalyzerTable

Network traffic passing through ports is analyzed by sending a copy of the traffic to another port on the same or different switch. This table contains the analyzer parameters.

jnxAnalyzerEntry

A row instance contains the Anlayzer Name, Analyzer Status, Mirroring Ratio, Loss Priority.

jnxAnalyzerName

This object identifies a unique Anlayzer configured on the switch.

jnxAnalyzerStatus

This object identifies whether the mirroring associated with a particular analyzer is enabled or disabled.

jnxMirroringRatio

This object will specify the mirroring ratio. User can configure the analyzer to mirror only one out of X packets [1:X packets] in the ingress/egress side based on whether the port is configured for ingress or egress mirroring. The configuration supports ...

jnxLossPriority

The analyzer port may be congested when the number of packets exceeds the bandwidth of the analyzer port. So the loss-priority parameter is enabled. The switched packets will not get affected by this. The value 0 corresponds to low priority.The value 1 co ...

jnxAnalyzerInputTable

An anlayzer Session is an association of several source ports to a destination port.A range or series of ports can be mirrored in a session.

jnxAnalyzerInputEntry

An Entry is created for each Input Source port.

jnxAnalyzerInputValue

This identifies each different analyzer input source. If the value of jnxAnalyzerInputType is 1 then jnxAnalyzerInputValue refers to the input source Interface Name. If the value of jnxAnalyzerInputType is 2 then jnxAnalyzerInputValue refers to the input ...

jnxAnalyzerInputOption

A source port is a switch port that is been mirrored. It can be mirrored based either on Ingress(received) traffic or egress (transmitted) traffic. The goal of receive (or ingress) Analyzer is to monitor as much as possible all the packets received by the ...

jnxAnalyzerInputType

This specifies whether interfaces or VLANs is mirrored. Mirroring can be done on the basis of the interface name.All packets received on a port configured for ingress mirroring is sent to the analyzer port.All packets sent out on a port configured for egr ...

jnxAnalyzerOutputTable

This table describes the destination port to which the traffic from the source ports are copied.

jnxAnalyzerOutputEntry

An Entry is created for each destination port or destination vlan.

jnxAnalyzerOutputValue

This object identifies each different destination port or destination vlan. If the value of jnxAnalyzerOutputType is 1 then jnxAnalyzerOutputValue gives the destination interface name. If the value of jnxAnalyzerOutputType is 2 then jnxAnalyzerOutputValue ...

jnxAnalyzerOutputType

The destination port can be on the same switch or on a different switch(Remote Analyzer). Value 1 specifies that the destination interface is on the same switch and it receives a copy of traffic from the source ports. The port does not transmit any traffi ...

jnxExAnalyzerInputTable

An anlayzer Session is an association of several source ports to a destination port.A range or series of ports can be mirrored in a session.

jnxExAnalyzerInputEntry

An Entry is created for each Input Source port.

jnxExAnalyzerInputOption

A source port is a switch port that is been mirrored. It can be mirrored based either on Ingress(received) traffic or egress (transmitted) traffic. The goal of receive (or ingress) Analyzer is to monitor as much as possible all the packets received by the ...

jnxExAnalyzerInputValue

This identifies each different analyzer input source. If the value of jnxExAnalyzerInputType is 1 then jnxExAnalyzerInputValue refers to the input source Interface Name. If the value of jnxExAnalyzerInputType is 2 then jnxExAnalyzerInputValue refers to th ...

jnxExAnalyzerInputType

This specifies whether interfaces or VLANs is mirrored. Mirroring can be done on the basis of the interface name.All packets received on a port configured for ingress mirroring is sent to the analyzer port.All packets sent out on a port configured for egr ...