LIEBERT-SERIES-300-UPS-MIB Download
This MIB defines objects for the Liebert AP300 SNMP Agents
IPHost Network Monitor offer an easy way of SNMP monitoring your Liebert Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for LIEBERT-SERIES-300-UPS-MIB
- lcUpsIdentManufacturer
- The UPS manufacturer.
- lcUpsIdentModel
- The UPS Model designation.
- lcUpsIdentSoftwareVersion
- The UPS SNMP Agent software version.
- lcUpsIdentSpecific
- A reference to MIB definitions specific to the particular UPS being managed. This object is used to locate the product-specific MIB for this device. If this information is not present, its value should be the OBJECT IDENTIFIER { 0 0 }, which is a syntacti ...
- lcUpsBatTimeRemaining
- The estimated time to depletion of battery charge. (Unit of measure: Minute)
- lcUpsBatVoltage
- The current battery voltage. (Unit of measure: volt)
- lcUpsBatCurrent
- The current battery discharging/charging current. (Unit of measure: Amp)
- lcUpsInputFrequency
- The current input frequency. (Unit of measure: Hertz)
- lcUpsInputBrownOuts
- The number of brown-out conditions the UPS has experienced.
- lcUpsInputBlackOuts
- The number of black-out conditions the UPS has experienced.
- lcUpsInputTransients
- The number of transient (surge and spike) conditions the UPS has experienced.
- lcUpsInputNumLines
- The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
- lcUpsInputTable
- lcUpsInputEntry
- lcUpsInputLine
- The input Line.
- lcUpsInputVoltage
- The input voltage. (Unit of measure: Volt)
- lcUpsInputCurrent
- The input current. (Unit of measure: Amp)
- lcUpsInputVA
- The input volt-amps.
- lcUpsOutputFrequency
- The current output frequency. (Unit of measure: Hertz)
- lcUpsOutputLoad
- The current output load percentage.
- lcUpsOutputNumLines
- The number of output lines utilized in this device. This entry indicates the number of rows in the output table.
- lcUpsOutputTable
- lcUpsOutputEntry
- lcUpsOutputLine
- The output Line.
- lcUpsOutputVoltage
- The output voltage. (Unit of measure: Volt)
- lcUpsOutputCurrent
- The output current. (Unit of measure: Amp)
- lcUpsOutputVA
- The output volt-amps.
- lcUpsInverterStatus
- The state of the inverter. Unknown is returned if the state can not be determined.
- lcUpsInverterTemp
- The temperature of the inverter. (Unit of measure: degree, Centigrade)
- lcUpsAlarms
- The current number of alarm conditions.
- lcUpsAlarmTable
- lcUpsAlarmEntry
- lcUpsAlarmId
- A unique identifier for an alarm condition. This value must remain constant between agent initializations.
- lcUpsAlarmDescr
- A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.
- lcUpsAlarmTime
- The value of sysUpTime when the alarm condition occured.
- lcUpsTestBattery
- Setting this variable to 'start' will initiate the battery test. Setting this variable to 'abort' will stop the battery test if the test is in- progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this variable ...
- lcUpsTestBatteryStatus
- The status of the battery test.
- lcUpsTestDiag
- Setting this variable to 'start' will initiate the diagnostics test. Setting this variable to 'abort' will stop the diagnostics test if the test is in-progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this v ...
- lcUpsTestDiagStatus
- The status of the diagnostics test.
- lcUpsControlOutputOffDelay
- Setting this object causes the agent to instruct the UPS to turn off the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOffTrap when the countdown ...
- lcUpsControlOutputOnDelay
- Setting this object causes the agent to instruct the UPS to turn on the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOnTrap when the countdown f ...
- lcUpsControlOutputOffTrapDelay
- When 'lcUpsControlOutputOffDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOffWarningTrap will be produced and this object will be reset to 0.
- lcUpsControlOutputOnTrapDelay
- When 'lcUpsControlOutputOnDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOnWarningTrap will be produced and this object will be reset to 0.
- lcUpsControlUnixShutdownDelay
- Setting this object causes the agent to instruct the UPS to perform a UNIX Shutdown in the indicated number of seconds. The agent counts down the number of seconds until the event will take place. A Unix shutdown is only valid if the UPS is on Battery. ...
- lcUpsControlUnixShutdownTrapDelay
- When 'lcUpsControlUnixShutdownDelay' reaches a value less than or equal to this object's value, an lcUpsUnixShutdownWarningTrap will be produced and this object will be reset to 0.
- lcUpsControlCancelCommands
- Setting this variable to 'cancel' will cause the agent to issue instructions to the UPS to cancel all outstanding commands, such as lcUpsControlOutputOff, lcUpsControlOutputOn, lcUpsControlUnixShutdown.
- lcUpsControlRebootAgentDelay
- Setting this object causes the agent to reboot after the indicated number of seconds have expired. The value will count down until the event takes place. The command can be cancelled by setting lcUpsControlCancleCommand to the value cancel.
- lcUpsNominalOutputVoltage
- The nominal output voltage. (Unit of measure: volt)
- lcUpsNominalInputVoltage
- The nominal input voltage. (Unit of measure: volt)
- lcUpsNominalOutputVA
- The nominal Volt-Amp rating.
- lcUpsNominalOutputWatts
- The nominal power rating. (Unit of measure: watt)
- lcUpsNominalOutputFreq
- The nominal output frequency. (Unit of measure: Hertz)
- lcUpsNominalInputFreq
- The nominal input frequency. (Unit of measure: Hertz)
- lsUpsIdentFirmwareVersion
- The firmware revision level of the UPS.
- lsUpsConfigBypassInstalled
- Indicates if a bypass is installed in the UPS.
- lsUpsOnBypass
- Indicates that the UPS is currently on bypass.
- lsUpsBypassFrequency
- The current bypass frequency. (Unit of measure: Hertz)
- lsUpsBypassNumLines
- The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
- lsUpsBypassTable
- lsUpsBypassEntry
- lsUpsBypassLine
- The bypass Line.
- lsUpsBypassVoltage
- The bypass voltage. (Unit of measure: Volt)
- lsUpsBypassCurrent
- The bypass current. (Unit of measure: Amp)
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
