Nortel-Magellan-Passport-OamEthernetMIB

Nortel-Magellan-Passport-OamEthernetMIB Download

MIBs list

The module describing the Nortel Magellan Passport OamEthernet Enterprise MIB.

IPHost Network Monitor offer an easy way of SNMP monitoring your Nortel network devices, Firewalls, Repeaters.

OID list for Nortel-Magellan-Passport-OamEthernetMIB

lpOamEnetRowStatusTable
This entry controls the addition and deletion of lpOamEnet components.
lpOamEnetRowStatusEntry
A single entry in the table represents a single lpOamEnet component.
lpOamEnetRowStatus
This variable is used as the basis for SNMP naming of lpOamEnet components. These components can be added and deleted.
lpOamEnetComponentName
This variable provides the component's string name for use with the ASCII Console Interface
lpOamEnetStorageType
This variable represents the storage type value for the lpOamEnet tables.
lpOamEnetIndex
This variable represents the index for the lpOamEnet tables.
lpOamEnetCidDataTable
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
lpOamEnetCidDataEntry
An entry in the lpOamEnetCidDataTable.
lpOamEnetCustomerIdentifier
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level compo ...
lpOamEnetIfEntryTable
This group contains the provisionable attributes for the ifEntry.
lpOamEnetIfEntryEntry
An entry in the lpOamEnetIfEntryTable.
lpOamEnetIfAdminStatus
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
lpOamEnetIfIndex
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
lpOamEnetProvTable
This group contains provisioned attributes for the OamEthernet component.
lpOamEnetProvEntry
An entry in the lpOamEnetProvTable.
lpOamEnetApplicationFramerName
This attribute specifies which Lan Application is running on this port.
lpOamEnetSwitchoverOnFailure
This attribute specifies if a CP switchover event should occur if a port or link failure is detected by the initial test process or if a steady state link failure is observed. This attribute can be set to one of the following values: enabled: This value i ...
lpOamEnetExtendedStatistics
This attribute specifies if extended statistics are to be collected for the OamEthernet component. The extended statistics include: singleCollisionFrames, multipleCollisionFrames, lateCollisions, excessiveCollisions, carrierSenseErrors, and clearToSendSig ...
lpOamEnetAdminInfoTable
This group contains the attributes pertaining to the vendor of the equipment.
lpOamEnetAdminInfoEntry
An entry in the lpOamEnetAdminInfoTable.
lpOamEnetVendor
This is the name of the vendor supplying the facility.
lpOamEnetCommentText
Any miscellaneous text about the facility.
lpOamEnetStateTable
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...
lpOamEnetStateEntry
An entry in the lpOamEnetStateTable.
lpOamEnetAdminState
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...
lpOamEnetOperationalState
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...
lpOamEnetUsageState
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...
lpOamEnetOperStatusTable
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
lpOamEnetOperStatusEntry
An entry in the lpOamEnetOperStatusTable.
lpOamEnetSnmpOperStatus
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operation ...
lpOamEnetOperTable
This group contains the operational attributes of the OamEthernet component.
lpOamEnetOperEntry
An entry in the lpOamEnetOperTable.
lpOamEnetMacAddress
This attribute indicates the medium access controller (MAC) address automatically assigned to the OAM Ethernet port by the system. The MAC address is displayed in canonical format.
lpOamEnetActiveStatus
This attribute indicates the status of the Oam Ethernet port on the active CP.
lpOamEnetStandbyStatus
This attribute indicates the status of the Oam Ethernet port on the standby CP.
lpOamEnetOamEnetStatsTable
This group contains statistical attributes for the OamEthernet component.
lpOamEnetOamEnetStatsEntry
An entry in the lpOamEnetOamEnetStatsTable.
lpOamEnetClearToSendSignalLoss
This attribute indicates the number of times that the clear to send signal was lost when attempting to transmit a frame. This counter wraps to zero when it exceeds its maximum value. This attribute is only active if the extendedStatistics attribute is ena ...
lpOamEnetFrameTooShort
This attribute indicates the number of frames received whose length is less than the allowed minimum frame length. This counter wraps to zero when it exceeds its maximum value.
lpOamEnetNumberOfRxCollisions
This attribute indicates the number of collisions detected during reception. This counter wraps to zero when it exceeds its maximum value.
lpOamEnetLackOfResourcesDiscards
This attribute indicates the number of good frames discarded because of a lack of resources available to contain them on the system. This counter wraps to zero when it exceeds its maximum value.
lpOamEnetOverrunErrors
This attribute indicates the number of frames known to be lost because the local system bus was not available. This counter wraps to zero when it exceeds its maximum value.
lpOamEnetStatsTable
This group contains statistical attributes for the Ethernet component.
lpOamEnetStatsEntry
An entry in the lpOamEnetStatsTable.
lpOamEnetAlignmentErrors
The alignmentErrors counter indicates the number of frames received which were not an integral number of octets in length. Frames will be checked for alignmentErrors before they are checked for Frame Check Sequence (FCS) errors. If there is an alignment e ...
lpOamEnetFcsErrors
The fcsErrors, Frame Check Sequence (FCS) error, counter indicates the number of frames received which were an integral number of octets in length and did not pass the FCS check. This counter will wrap around after it reaches its maximum value.
lpOamEnetSingleCollisionFrames
The singleCollisionFrames counter indicates the number of frames successfully transmitted which experienced exactly one collision. This counter will wrap around after it reaches its maximum value.
lpOamEnetMultipleCollisionFrames
The multipleCollisionFrames counter indicates the number of frames successfully transmitted which experienced more than one collision. This counter will wrap around after it reaches its maximum value.
lpOamEnetSqeTestErrors
The sqeTestErrors, Signal Quality Error (SQE) Test errors, counter indicates the number of times the 'SQE Test Error' message has been generated for the station. This counter will wrap around after it reaches its maximum value.
lpOamEnetDeferredTransmissions
The deferredTransmissions counter indicates the number of frames which experienced a transmission delay because the medium was busy. This counter will wrap around after it reaches its maximum value.
lpOamEnetLateCollisions
The lateCollisions counter indicates the number of times a collision was detected later than 512 bit-times into the transmission of a packet. This counter will wrap around after it reaches its maximum value.
lpOamEnetExcessiveCollisions
The excessiveCollisions counter indicates the number of frames which failed to get transmitted due to excessive collisions. This counter will wrap around after it reaches its maximum value.
lpOamEnetMacTransmitErrors
The Medium Access Controller (MAC) transmit error counter indicates the number of times that a transmission failed due to internal MAC transmit errors. This counter will wrap around after it reaches its maximum value.
lpOamEnetCarrierSenseErrors
The carrier sense error counter indicates the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame. This counter will wrap around after it reaches its maximum value.
lpOamEnetFrameTooLongs
The frame too long counter indicates the number of frames received which exceeded the maximum frame size. This counter will wrap around after it reaches its maximum value.
lpOamEnetMacReceiveErrors
The Medium Access Controller (MAC) receive error counter indicates the number of times a receive failed due to internal MAC receive errors. This counter will wrap around after it reaches its maximum value.
lpOamEnetTestRowStatusTable
This entry controls the addition and deletion of lpOamEnetTest components.
lpOamEnetTestRowStatusEntry
A single entry in the table represents a single lpOamEnetTest component.
lpOamEnetTestRowStatus
This variable is used as the basis for SNMP naming of lpOamEnetTest components. These components cannot be added nor deleted.
lpOamEnetTestComponentName
This variable provides the component's string name for use with the ASCII Console Interface
lpOamEnetTestStorageType
This variable represents the storage type value for the lpOamEnetTest tables.
lpOamEnetTestIndex
This variable represents the index for the lpOamEnetTest tables.
lpOamEnetTestOperTable
This group contains the operational data for the Test component.
lpOamEnetTestOperEntry
An entry in the lpOamEnetTestOperTable.
lpOamEnetTestType
This attribute is the type of test to be run. The four types of tests available are: the port hardware logic test, the configure and dump memory registers test, the memory mapping test and the Time Domain Reflectometry (TDR) test. The possible values of t ...
lpOamEnetTestResultsTable
This group contains all the statistics related attributes of the Test component.
lpOamEnetTestResultsEntry
An entry in the lpOamEnetTestResultsTable.
lpOamEnetTestCauseOfTermination
This attribute records the reason why the test terminated. The possible values of this attribute are: testTimeExpired: this value indicates the time allotted for the test to run has expired which caused the test terminate. If the port is locked without th ...
lpOamEnetTestTestResult
This attribute records the result of last port test executed on the OAM Ethernet port. The result can be one of the following values. pass: the test passed fail: the test failed neverRun: the test has not been run running: the test is running

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list