Nortel-Magellan-Passport-VnetEtsiQsigMIB Download

sigChanEQsigRowStatusTable

This entry controls the addition and deletion of sigChanEQsig components.

sigChanEQsigRowStatusEntry

A single entry in the table represents a single sigChanEQsig component.

sigChanEQsigRowStatus

This variable is used as the basis for SNMP naming of sigChanEQsig components. These components can be added and deleted.

sigChanEQsigComponentName

This variable provides the component's string name for use with the ASCII Console Interface

sigChanEQsigStorageType

This variable represents the storage type value for the sigChanEQsig tables.

sigChanEQsigIndex

This variable represents the index for the sigChanEQsig tables.

sigChanEQsigL2Table

This group specifies the provisionable layer 2 attributes of the Q.931 ITU-T protocol.

sigChanEQsigL2Entry

An entry in the sigChanEQsigL2Table.

sigChanEQsigT23

This attribute specifies the layer 2 enable request timer.

sigChanEQsigT200

This attribute specifies the maximum time between a layer 2 frame and its acknowledgment.

sigChanEQsigN200

This attribute specifies the maximum number of re-transmissions of a layer 2 frame.

sigChanEQsigT203

This attribute specifies the maximum time for which layer 2 frames may be absent. Expiry triggers a check on whether the far end is alive.

sigChanEQsigCircuitSwitchedK

This attribute specifies the maximum number of sequentially numbered I frames (that is, window size (k)) that may be unacknowledged at any given time for a SAP supporting primary rate (64kbit/sec) signalling.

sigChanEQsigL3Table

This group represents the provisionable Layer 3 timer attributes of the ETSI Qsig protocol.

sigChanEQsigL3Entry

An entry in the sigChanEQsigL3Table.

sigChanEQsigT309

This attribute specifies the data link failure timer; used to ride out temporary failures.

sigChanEQsigT310

This attribute specifies the call proceeding state timer.

sigChanEQsigProvTable

This group defines the general options of the D-channel signalling link.

sigChanEQsigProvEntry

An entry in the sigChanEQsigProvTable.

sigChanEQsigSide

This attribute specifies whether the interface is the network or user side of the connection. The parameter applies to both the layer 2 and layer 3 of the interface. If this attribute is set to network, then the interface is master during channel negotiat ...

sigChanEQsigMaxNonCallConcurrent

This attribute specifies the maximum number of simultaneous active non-call messages that are allowed.

sigChanEQsigOverlapSendingEnabled

This attribute specifies whether overlap sending to the PBX is enabled.

sigChanEQsigOverlapReceivingEnabled

This attribute specifies whether overlap receiving from the PBX is enabled.

sigChanEQsigStateTable

This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...

sigChanEQsigStateEntry

An entry in the sigChanEQsigStateTable.

sigChanEQsigAdminState

This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...

sigChanEQsigOperationalState

This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...

sigChanEQsigUsageState

This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...

sigChanEQsigStatsTable

This group provides the operational components for the EtsiQsig component.

sigChanEQsigStatsEntry

An entry in the sigChanEQsigStatsTable.

sigChanEQsigTotalCallsToIf

This attribute counts the total number of calls that have been made to the interface. The value wraps when it reaches its maximum.

sigChanEQsigTotalCallsFromIf

This attribute counts the total number of calls from the interface. The value wraps when it reaches its maximum.

sigChanEQsigNonCallAssocSessionsToIf

This attribute counts the total number of non-call associated sessions to the interface. The value wraps when it reaches its maximum.

sigChanEQsigNonCallAssocSessionsFromIf

This attribute counts the total number of non-call associated sessions from the interface. The value wraps when it reaches its maximum.

sigChanEQsigOperTable

This group provides the operational attributes for the EtsiQsig protocol.

sigChanEQsigOperEntry

An entry in the sigChanEQsigOperTable.

sigChanEQsigActiveChannels

This attribute indicates the number of currently active channels. This includes data and voice channels.

sigChanEQsigActiveVoiceChannels

This attribute indicates the number of channels that are currently carrying voice.

sigChanEQsigActiveDataChannels

This attribute indicates the number of channels that are currently carrying data. This does not include modem data.

sigChanEQsigPeakActiveChannels

This attribute indicates the maximum number of channels that have been active on this signalling channel during the last polling period.

sigChanEQsigPeakActiveVoiceChannels

This attribute indicates the maximum number of voice channels that have been active on this signalling channel during the last polling period.

sigChanEQsigPeakActiveDataChannels

This attribute indicates the maximum number of data channels that have been active on this signalling channel during the last polling period.

sigChanEQsigDChanStatus

This attribute indicates the state of the D-channel. outOfService means that there is no layer 2 or layer 3 connectivity to the PBX. establishing means that the signalling channel is attempting to stage the layer 2. established means that the layer 2 is e ...

sigChanEQsigToolsTable

This contains a series of operational attributes which turn on and off several kinds of tracing.

sigChanEQsigToolsEntry

An entry in the sigChanEQsigToolsTable.

sigChanEQsigTracing

This attribute defines which types of tracing are active for this signalling channel. The tracing messages are sent to the debug stream. To see the messages the agentQueue attribute in Col/debug must be greater than 0 and a Telnet NMIS session must list ...

sigChanEQsigEQsigSpecificProvTable

This group provides EtsiQsig protocol specific provisioning.

sigChanEQsigEQsigSpecificProvEntry

An entry in the sigChanEQsigEQsigSpecificProvTable.

sigChanEQsigMsgSegmentation

This attribute allows users to enable/disable the EtsiQsig message segmentation service.

sigChanEQsigE1ChannelNumbers

This attribute is applicable to E1 interfaces only. It specifies the mapping scheme between channel numbers (identified in Layer 3 messages) and timeslot numbers on the E1 link. When the attribute value is skip16, channel numbers map directly to actual E1 ...

sigChanEQsigEQsigSpecificOpTable

This group provides specific operational attributes for the Etsi Qsig protocol.

sigChanEQsigEQsigSpecificOpEntry

An entry in the sigChanEQsigEQsigSpecificOpTable.

sigChanEQsigSegmentationAccepted

This attribute counts the total number of times a long Etsi Qsig message has been received from a PBX and forwarded to a Passport subnet. The value wraps when it reaches its maximum.

sigChanEQsigSegmentationFailed

This attribute counts the total number of times a long Etsi Qsig message has been received from a PBX and could not be forwarded as is to a Passport subnet due to end-to-end incompatibility. The value wraps when it reaches its maximum.

sigChanEQsigFramerRowStatusTable

This entry controls the addition and deletion of sigChanEQsigFramer components.

sigChanEQsigFramerRowStatusEntry

A single entry in the table represents a single sigChanEQsigFramer component.

sigChanEQsigFramerRowStatus

This variable is used as the basis for SNMP naming of sigChanEQsigFramer components. These components cannot be added nor deleted.

sigChanEQsigFramerComponentName

This variable provides the component's string name for use with the ASCII Console Interface

sigChanEQsigFramerStorageType

This variable represents the storage type value for the sigChanEQsigFramer tables.

sigChanEQsigFramerIndex

This variable represents the index for the sigChanEQsigFramer tables.

sigChanEQsigFramerProvTable

This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.

sigChanEQsigFramerProvEntry

An entry in the sigChanEQsigFramerProvTable.

sigChanEQsigFramerInterfaceName

This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.

sigChanEQsigFramerStateTable

This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...

sigChanEQsigFramerStateEntry

An entry in the sigChanEQsigFramerStateTable.

sigChanEQsigFramerAdminState

This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...

sigChanEQsigFramerOperationalState

This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...

sigChanEQsigFramerUsageState

This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...

sigChanEQsigFramerStatsTable

This group contains the operational statistics data for a Framer component.

sigChanEQsigFramerStatsEntry

An entry in the sigChanEQsigFramerStatsTable.

sigChanEQsigFramerFrmToIf

This attribute counts the number of frames transmitted to the link interface by Framer. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerFrmFromIf

This attribute counts the number of frames received from the link interface by Framer. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerOctetFromIf

The number of bytes received from the link interface by Framer.

sigChanEQsigFramerAborts

This attribute counts the total number of aborts received. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerCrcErrors

This attribute counts the total number of frames with CRC errors. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerLrcErrors

This attribute counts the total number of frames with LRC errors. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerNonOctetErrors

This attribute counts the total number of frames that were non octet aligned. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerOverruns

This attribute counts the total number of frames received from the link for which overruns occurred. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerUnderruns

This attribute counts the total number of frames transmitted to the link for which underruns occurred. This count wraps to zero after reaching its maximum value.

sigChanEQsigFramerLargeFrmErrors

This attribute counts the total number of frames received which were too large (longer than 500 bytes). This count wraps to zero after reaching its maximum value.