ctron-deciv-router-mib Download

nwDecIVMibRevText

Indicates the current revision level of the DECnet Phase IV MIB in textual format.

nwDecIVSysRouterId

The DECnet Address used to uniquely identify the host (device) running DECnet Phase IV Routing Services. Since DECnet Phase IV uses a single address to identify the host and all of its router ports, rather than using an address per router port, nwDecIVSys ...

nwDecIVNodeType

Specifies the node type. Setting this value to 2, (routing-iv), establishes the Routing Services-enabled device as a DECnet Level 1, intra-area router. Setting this value to 2, establishes the Routing Services-enabled device as a DECnet Phase IV Level 2, ...

nwDecIVMaxNodes

Specifies the maximum number of DECnet nodes allowed within an area.

nwDecIVMaxBRA

Specifies the maximum number of router adjacencies supported by this node.

nwDecIVMaxBEA

Specifies the maximum number of endnode adjacencies supported by this node.

nwDecIVMaxHops

Specifies the maximum number of hops allowed for a valid route within the area. Any intra-area route consisting of a greater number of hops than specified by nwDecIVMaxHops is considered unreachable.

nwDecIVMaxCost

Specifies the maximum cost allowed for a valid route within the area. Any intra-area route with a cost greater than nwDecIVMaxCost is considered unreachable.

nwDecIVMaxVisits

Specifies the maximum number of intra-area hops a packet can be forwarded. A packet is dropped once it has been forwarded nwDecIVMaxVisits.

nwDecIVNonBroadcastTimer

Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table, on any non-broadcast networks attached to any router port configured and enabled for DECnet Phase IV Routing Services.

nwDecIVBroadcastTimer

Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table on any multi-access broadcast networks attached to any router port configured and enabled for DECnet Phase IV Routing Services.

nwDecIVAreas

Specifies the maximum number of areas allowed within a Level 2 (inter-area)routing domain.

nwDecIVMaxAreaHops

Specifies the maximum number of areas that can be hopped by a valid inter-area route. Any inter-area route requiring a greater number of areas to be hopped than specified by nwDecIVMaxAreaHops is considered invalid.

nwDecIVMaxAreaCost

Specifies the maximum cost allowed for a valid Level 2 (inter-area) route. Any inter-area route with a cost greater than nwDecIVMaxAreaCost is considered unreachable.

nwDecIVSysAdminStatus

Sets the administrative state of DECnet Phase IV Routing Services, system-wide. Enabled (3) causes DECnet Phase IV system-wide Routing Services to become active on all router ports configured and enabled for DECnet Phase IV Routing Services. Disabled (2) ...

nwDecIVSysOperStatus

Indicates the current operating condition of DECnet Phase IV Routing Services system-wide. The value of nwDecIVSysOperStatus indicates any problem with your DECnet Phase IV Routing Services configuration. A value of 6 indicates that regardless of the valu ...

nwDecIVSysAdminReset

Resets DECnet Phase IV Routing Services, system-wide. Reset (2) forces a restart of DECnet Phase IV Routing Services without a graceful shutdown on any active router ports and without affecting any other routing services.

nwDecIVSysOperationalTime

Indicates the elapsed time, in hundredths of a second, that nwDecIVSysOperStatus has been in it's current state.

nwDecIVSysVersion

Indicates the current revision level of the DECnet Phase IV Routing Services firmware, in textual format.

nwDecIVFwdCtrAdminStatus

Sets the administrative state of the aggregate (system-wide) DECnet packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.

nwDecIVFwdCtrReset

Resets the aggregate (system-wide) DECnet packet and byte counters. Reset (2) resets the DECnet aggregate counters to 0. nwDecIVFwdCtrOperationalTime is also reset to 0.

nwDecIVFwdCtrOperationalTime

Indicates the elapsed time, in hundredths of a second, that DecIVFwdCtrOperStatus has been in the current state.

nwDecIVFwdCtrInPkts

Indicates the total number of DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrOutPkts

Indicates the total number of DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrFwdPkts

Indicates the total number of DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrFilteredPkts

Indicates the total number of DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrDiscardPkts

Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrAddrErrPkts

Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of addressing errors in the DECnet header.

nwDecIVFwdCtrLenErrPkts

Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because an invalid packet length is contained in the DECnet header.

nwDecIVFwdCtrHdrErrPkts

Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of an invalid DECnet header.

nwDecIVFwdCtrInBytes

Indicates the total number of bytes in the DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrOutBytes

Indicates the total number of bytes in the DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrFwdBytes

Indicates the total number of bytes in the DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrFilteredBytes

Indicates the total number of bytes in the DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrDiscardBytes

Indicates the total number of bytes in the DECnet packets that have been discarded, system wide, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrHostInPkts

Indicates the total number of DECnet packets that have been successfully delivered to the local host, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrHostOutPkts

Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrHostDiscardPkts

Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of host resources.

nwDecIVFwdCtrHostInBytes

Indicates the total number of bytes in the DECnet packets that have been received by the local host, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrHostOutBytes

Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdCtrHostDiscardBytes

Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of host resources.

nwDecIVFwdIfTable

This table contains an entry for each router port. This table is indexed by nwDecIVFwdIfIndex, which indicates the value of MIB 2 ifIndex, which identifies the router port for which each entry exists.

nwDecIVFwdIfEntry

Each entry specifies the DECnet Phase IV Routing Services configuration for the router port for which the entry exists.

nwDecIVFwdIfIndex

Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.

nwDecIVFwdIfAdminStatus

Sets the administrative state of DECnet Phase IV Routing Services on the router port for which the entry exists. Enabled (3) causes DECnet Phase IV Routing Services to become active. Disabled (2) causes it to become inactive.

nwDecIVFwdIfOperStatus

Indicates the current operating condition of DECnet Phase IV Routing Services on the router port for which the entry exists. The value of nwDecIVFwdIfOperStatus indicates any problem with the configuration of DECnet Phase IV Routing Services on the router ...

nwDecIVFwdIfOperationalTime

Indicates the elapsed time, in hundredths of a second, that nwDecIVFwdIfOperStatus has been in its current state.

nwDecIVFwdIfControl

This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVFwdIfMtu

Specifies the Maximum Transmission Unit (MTU) for DECnet packets on the router port for which the entry exists. This includes the DECnet header and data, but does not include framing.

nwDecIVFwdIfForwarding

Controls the forwarding of DECnet packets on the router port for which the entry exists. Enabled (3) causes DECnet packets to be forwarded. Disabled (2) prevents DECnet packets from being forwarded.

nwDecIVFwdIfFrameType

Specifies the framing type for DECnet packets forwarded on the router port for which the entry exists. Some frame types are only valid for specific media types. The comments reflect those valid media types.

nwDecIVFwdIfAclIdentifier

Specifies the Access Control ID of the access control list in effect for DECnet packets being routed on the router port for which the entry exists. A value of 0 indicates that no access control list is in effect.

nwDecIVFwdIfAclStatus

Controls the operation of any access control list configured for DECnet traffic on the router port for which the entry exists. Enabled (3) applies the access control list indicated by the value of nwDecIVFwdIfAclIdentifier to all DECnet traffic being rout ...

nwDecIVFwdIfCacheControl

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVFwdIfCacheEntries

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVFwdIfCacheHits

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVFwdIfCacheMisses

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVFwdIfCtrTable

This table contains an entry for each router port configured and enabled for DECnet Phase IV Routing Services.

nwDecIVFwdIfCtrEntry

Each entry indicates the current packet and byte count of DECnet packets on each router port for which the entry exists.

nwDecIVFwdIfCtrIfIndex

Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.

nwDecIVFwdIfCtrAdminStatus

Sets the administrative state of the per-port DECnet packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.

nwDecIVFwdIfCtrReset

Resets the per-port DECnet packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwDecIVFwdIfCtrOperationalTime is also reset to 0.

nwDecIVFwdIfCtrOperationalTime

Indicates the elapsed time, in hundredths of a second, that the per-port DECnet packet and byte counters have been active on the router port for which the entry exists.

nwDecIVFwdIfCtrInPkts

Indicates the total number of DECnet packets that have been received, during nwDecIVFwdIfCtrOperationaltime, on the router port for which the entry exists.

nwDecIVFwdIfCtrOutPkts

Indicates the total number of DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrFwdPkts

Indicates the total number of DECnet packets that have been forwarded on the router port for which the entry exists, during nwDecIVFwdCtrOperationalTime.

nwDecIVFwdIfCtrFilteredPkts

Indicates the total number of DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrDiscardPkts

Indicates the total number of DECnet packets that have been discarded (dropped), during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrAddrErrPkts

Indicates the total number of DECnet packets that have been discarded because of addressing errors in the DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrLenErrPkts

Indicates the total number of DECnet packets that have been discarded because an invalid packet length was contained in the DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrHdrErrPkts

Indicates the total number of DECnet packets that have been discarded because of an invalid DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrInBytes

Indicates the total number of bytes in the DECnet packets that have been received, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrOutBytes

Indicates the total number of bytes in the DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrFwdBytes

Indicates the total number of bytes in the DECnet packets that have been forwarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrFilteredBytes

Indicates the total number of bytes in the DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrDiscardBytes

Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrHostInPkts

Indicates the total number of DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.

nwDecIVFwdIfCtrHostOutPkts

Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrHostDiscardPkts

Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.

nwDecIVFwdIfCtrHostInBytes

Indicates the total number of bytes in the DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.

nwDecIVFwdIfCtrHostOutBytes

Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVFwdIfCtrHostDiscardBytes

Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, due to a lack of host resources, that were received on the router port for which the entry exists, during nwDecIVFwdIfCtrOperationalTime.

nwDecIVProtoAdminStatus

Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol system-wide. Enabled (3) causes the routing protocol to become active on all router ports configured and enabled for DECnet Routing Services. Disabled (2) causes t ...

nwDecIVProtoOperStatus

Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol system-wide. The value of nwDecIVProtoOperStatus indicates any problem with the DECnet Phase IV distance-vector-based routing protocol configuration. A ...

nwDecIVProtoAdminReset

Resets the DECnet Phase IV distance-vector-based routing protocol. Reset (2) forces a system-wide restart of the protocol without a graceful shut-down on any active router ports.

nwDecIVProtoOperationalTime

Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoOperStatus has been in current state.

nwDecIVProtoVersion

Indicates the current revision level of the DECnet Phase IV distance-vector-based routing protocol firmware, in textual format.

nwDecIVProtoStackSize

Specifies the stack size of the DECnet Phase IV distance-vector- based routing protocol thread. In order for a change of this value to take effect, the protocol (nwDecIVProtoAdminReset), DECnet Phase IV Routing Services (nwDecIVSysAdminReset), or the devi ...

nwDecIVProtoThreadPriority

Specifies the run-time execution priority of the DECnet Phase IV distance-vector-based routing protocol thread. In order for a change of this value to take effect, the protocol (nwDecIVProtoAdminReset), DECnet Phase IV Routing Services (nwDecIVSysAdminRes ...

nwDecIVProtoDatabaseThreshold

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVProtoAgeOut

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVProtoHoldDown

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVProtoCtrAdminStatus

Sets the administrative state of the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.

nwDecIVProtoCtrReset

Resets the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Reset (2) resets the DECnet aggregate counters to 0. nwDecIVProtoCtrOperationalTime is also reset to 0.

nwDecIVProtoCtrOperationalTime

Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoCtrAdminStatus has been in it's current state.

nwDecIVProtoCtrInPkts

Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoCtrOutPkts

Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoCtrFilteredPkts

Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoCtrDiscardPkts

Indicates the total number of the DECnet Phase IV distance-vector -based routing protocol packets that have been discarded, system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoCtrInBytes

Indicates the total number of bytes in the DECnet Phase IV distance-vector based routing protocol packets that have been received, system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoCtrOutBytes

Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoCtrFilteredBytes

Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been administratively filtered, system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoCtrDiscardBytes

Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been discarded system-wide, during nwDecIVProtoCtrOperationalTime.

nwDecIVProtoIfTable

This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwDecIVProtoIfIndex, which indicates the value of MIB ...

nwDecIVProtoIfEntry

Each entry contains the DECnet Phase IV distance-vector-based routing protocol configuration for the router port for which the entry exists.

nwDecIVProtoIfIndex

Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.

nwDecIVProtoIfAdminStatus

Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Enabled (3) causes the routing protocol to become active on the router port. Disabled (2) causes it to become inacti ...

nwDecIVProtoIfOperStatus

Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. The value of nwDecIVProtoIfOperStatus indicates any problem with your routing protocol configuration on ...

nwDecIVProtoIfOperationalTime

Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfOperStatus has been in it`s current state.

nwDecIVProtoIfVersion

Indicates the revision level of the DECnet Phase IV distance-vector-based routing protocol firmware on the router port for which the entry exists, in textual format.

nwDecIVProtoIfAdvertisement

Sets the interval, in seconds, at which the DECnet Phase IV distance-vectorbased routing protocol advertises its route table on the router port for which the entry exists. Change this value to cause the DECnet Phase IV distance-vector-based routing protoc ...

nwDecIVProtoIfFloodDelay

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVProtoIfRequestDelay

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVProtoIfPriority

Sets the priority of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Within an area, the router with the highest value for nwDecIVProtoIfPriority becomes the priority or designated router. The high ...

nwDecIVProtoIfHelloTimer

Sets the interval, in seconds, at which DECnet Phase IV distance-vector-based routing protocol sends Hello packets on the router port for which the entry exists.

nwDecIVProtoIfSplitHorizon

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVProtoIfPoisonReverse

This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.

nwDecIVProtoIfSnooping

Controls the operation of DECnet Phase IV distance-vector-based routing protocol snooping on the router port. When snooping is enabled the DECnet Phase IV distance-vector-based routing protocol operates in passive mode, so that it receives route informati ...

nwDecIVProtoIfType

Indicates whether the directly connected network segment does or does not support broadcast media access.

nwDecIVProtoIfXmitCost

Sets the cost of transmitting a packet on the network segment connected to the router port for which the entry exists. The DECnet Phase IV distance-vector-based routing protocol picks the route with the least total nwDecIVProtoIfXmitCost as the best route ...

nwDecIVProtoIfAclIdentifier

Specifies the Access Control ID of the access control list in effect for DECnet Phase IV distance-vector-based routing protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect fo ...

nwDecIVProtoIfAclStatus

Controls the operation of the access control list identified by nwDecIVProtoIfAclIdentifier. Enabled (3) applies the access control list to all DECnet Phase IV distance-vector-based routing protocol packet traffic on the router port for which the entry ex ...

nwDecIVProtoIfCtrTable

This table contains an entry for each router port. This table is indexed by nwDecIVProtoIfCtrIfIndex which indicates the value of MIB2 ifindex, which identifies the router port for which the entry exists.

nwDecIVProtoIfCtrEntry

Each entry indicates the current packet and byte count of DECnet Phase IV distance-vector-based routing protocol packets on the router port for which the entry exists.

nwDecIVProtoIfCtrIfIndex

Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.

nwDecIVProtoIfCtrAdminStatus

Sets the administrative state of the per-port DECnet Phase IV distance-vectorbased routing protocol packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these count ...

nwDecIVProtoIfCtrReset

Resets the per-port DECnet Phase IV distance-vector-based routing protocol packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwDecIVProtoIfCtrOperationalTime is also reset to 0.

nwDecIVProtoIfCtrOperationalTime

Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfCtrAdminStatus has been in the current state.

nwDecIVProtoIfCtrInPkts

Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVProtoIfCtrOutPkts

Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVProtoIfCtrFilteredPkts

Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVProtoIfCtrDiscardPkts

Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exist.

nwDecIVProtoIfCtrInBytes

Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVProtoIfCtrOutBytes

Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.

nwDecIVProtoIfCtrFilteredBytes

Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exists.

nwDecIVProtoIfCtrDiscardBytes

Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exists.

nwDecIVFibTable

This table contains an entry for each route being used to forward DECnet data packets..

nwDecIVFibEntry

Each entry in the table describes a route to a particular DECnet destination network and node.

nwDecIVFibNodeId

Contains the DECnet Address of the destination node of the route for which the entry exists.

nwDecIVFibNextHopNodeId

Contains the DECnet Address of the next hop router for the route for which the entry exists.

nwDecIVFibNextHopIf

Indicates the value of MIB 2 ifindex, which identifies the router port through which the route exists.

nwDecIVFibRouteType

Indicates the status of the route. A value of 3 indicates that the destination is on the network segment that is directly connected to the router port identified by nwDecIVFibNextHopIf. A value of 4 indicates that the destination is on an indirectly conne ...

nwDecIVAclValidEntries

Indicates the number of valid entries that exist in the access control list table, nwDecIVAclTable.

nwDecIVAclTable

This table contains the access control list information for DECnet traffic. This table contains entries each of which specifies whether packet forwarding between a particular source destination pair is permitted or denied. Each entry is part of a particul ...

nwDecIVAclEntry

Each entry contains DECnet source/destination access information.

nwDecIVAclIdentifier

This is the primary (major) index into the DECnet access control list table. This value identifies each access control list by a unique identifier, a number arbitrarily assigned by the user. All entries that have the same value for nwDecIVAclIdentifier be ...

nwDecIVAclSequence

This is the secondary (minor) index into the DECnet access control list table. This number corresponds to a sequence number used to order multiple entries within the same access control list.

nwDecIVAclPermission

Specifies whether access is allowed or denied between the source and destination address pair. Note that source and destination are interchangeable when bi-directional control is selected. To remove an existing entry set nwDecIVAclPermission to invalid (2 ...

nwDecIVAclMatches

Indicates the number of matches on this entry that have resulted in the permit/deny access restriction being applied as part of the forwarding process.

nwDecIVAclDestAddress

Specifies the destination DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to 0, a wildcard value which matches all areas or all nodes.

nwDecIVAclSrcAddress

Specifies the source DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to a wildcard value which matches all areas or all nodes.

nwDecIVHostMapTable

The DecIV Address translation table used for mapping a DecIV address to a circuit identifier (if applicable), corresponding port number, and framing type.

nwDecIVHostMapEntry

Each entry contains one DecIVAddress to circuit equivalence. Also provided is the framing required to converse with this host, and the corresponding logical port number.

nwDecIVHostMapIfIndex

This is the primary (major) index into the DecIV HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the DecIV router port for which the entry exists.

nwDecIVHostMapDecIVAddr

The DecIVAddress of the host on the corresponding interface and circuit (if applicable).

nwDecIVHostMapType

Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwDecIVHostMapTable. That is, it effectively dissasociates the circuitand/or interface identified with said entry from the mapping identified with s ...

nwDecIVHostMapCircuitID

The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the DecIV Address at the end of the circuit. For non-WAN interfaces, the value of this object is zero.

nwDecIVHostMapFraming

Specifies the framing type required to converse with the host for which this entry exists.

nwDecIVHostMapPortNumber

The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of configured interfaces in the system and the number of circuits present on those interfaces which are of WAN type.

nwDecIVEventAdminStatus

Sets the administrative state of DECnet event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive.

nwDecIVEventMaxEntries

Sets the maximum number of entries allowed in the event log table. When the number of entries reaches the value of nwDecIVEventMaxEntries, the first (oldest) entry is deleted to allow a new entry to be added.

nwDecIVEventTraceAll

Enabled (3) allows logging of all event types on all router ports for all protocols and components. Disabled (2) causes the filter table to specify which events to log.

nwDecIVEventFilterTable

This table contains and entry for each event filter configured for DECnet Phase IV Routing Services events.

nwDecIVEventFilterEntry

Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwDecIVEventFltrProtocol indicates the value used either in the nwRtgProtocolTable or the nwComponentTable in the Cabletron Routing S ...

nwDecIVEventFltrProtocol

Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance which identifies the protocol involved in the event for which the event filter exists.

nwDecIVEventFltrIfNum

Specifies the router port involved in the event for which the event filter exists.

nwDecIVEventFltrControl

Set this value to 3 to add the entry to the event filter table. Set this value to 2 to remove the entry from the event filter table.

nwDecIVEventFltrType

This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting any bit to 0 removes an event type from this field and prevents that type of event from being log ...

nwDecIVEventFltrSeverity

Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than specified by this filter value. `Highmed' ignores only events of the lowest severity. `Highlow' logs ...

nwDecIVEventFltrAction

Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwDecIVEventLogTable). Logging to'trap' sends events out through the trap mechanism.

nwDecIVEventTable

This table contains an entry for each event that has been logged.

nwDecIVEventEntry

Each entry contains the information about an event that has been logged to the event table.

nwDecIVEventNumber

An ordinal value assigned to the event for which the log entry exists. nwDecIVEventNumber is assigned so that each event in the event log can be uniquely identified by the value of nwDecIVEventNumber.

nwDecIVEventTime

Indicates the time at which the event was logged to the event log.

nwDecIVEventType

Indicates the type of event that was logged.

nwDecIVEventSeverity

Indicates the severity that was assigned to the event.

nwDecIVEventProtocol

Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which identifies the protocol or component that was involved in the event.

nwDecIVEventIfNum

Indicates the router port that was involved in the event.

nwDecIVEventTextString

Contains the actual text string that was logged.