ctron-ssr-policy-mib Download

polAclServer

This is true when Access Control Lists (ACLs) are defined by a Policy Server else false. At boot, this value is false. After the first valid set of any policy object, the value changes to true.

polAclNumber

The number of Layer 3 Access Control Lists defined in the SSR.

polAclLastChanged

The time the Access Control List were last changed.

polAclTable

A list of Access Control List entries.

polAclEntry

A record containing a Access Control List.

polAclName

The administratively assigned name to this static route entry.

polAclItem

This row's unique identifier within a given ACL set. Member of the ACL set are numbered from 1 to 256. If Item is set to 0, and rowStatus is destroy, all rows for this set are destroyed.

polAclRestriction

The permissions/restrictions given to this static route entry.

polAclProtocol

The IETF protocol this ACL applies to.

polAclSrcIp

The source L3 IP Address this ACL applies to.

polAclSrcMask

The source L3 IP Mask this ACL Applies to.

polAclDstIp

The source L3 IP Address this ACL applies to.

polAclDstMask

The source L3 IP Mask this ACL Applies to.

polAclTOS

The source L3 IP Type of Service field.

polAclSrcPort

The source L3 IP source port/socket ACL applies to.

polAclDstPort

The source L3 IP destination port/socket ACL applies to.

polAclSrcOperator

polAclSrcPort is compared using this operator.

polAclDstOperator

polAclDstPort is compared using this operator.

polAclSrcHighRange

The high range source L3 IP port. Used only when SrcOperator == range. polAclSrcPort is used as the lower bounds of the range.

polAclDstHighRange

The high range destination L3 IP port. Used only when SrcOperator == range. polAclDstPort is used as the lower bounds of the range.

polAclAuditTrail

Flows matching this ACL are logged for Accounting when true.

polAclCheckpoint

How long to keep flow at which point a checkpoint should be done. A checkpoint may trigger earlier than this time should the maximum batch size be reached.

polAclRowStatus

SNMP V2 RowStatus control for this table.

polAclServiceNumber

The number of Layer 3 Access Control Lists in service in the SSR.

polAclServiceLastChanged

The time the ACLs in service were last changed.

polAclServiceTable

A list of ACL's currently in service.

polAclServiceEntry

A record containing a Access Control Lists applied to Interfaces.

polAclServiceIfIndex

The ifIndex of the IP Interface the ACL is applied to. An SSR IP Interface has ifType 142

polAclName2

The name of the ACL applied to the particular port.

polAclServiceDirection

The direction the ACL is applied to the particular port.

polAclServiceRowStatus

SNMP V2 RowStatus control for this table.

polAclRemoteAllowed

Remote Policy Configuration is allowed when true only local (to SSR) policy may be applied.

polAclInterfaceNumber

The number of Layer 3 Interfaces in service in the SSR.

polAclInterfaceLastChanged

The time the Interfaces in service were last changed with regard to policy.

polAclInterfaceTable

A list of IP Interfaces in service and their policy status. Each IP Interface can be defined to use local static policy or remote dynamic policy in the config.

polAclInterfaceEntry

A record containing a Access Control Lists applied to Interfaces.

polAclInterfaceIfIndex

The ifIndex of the IP Interface the ACL is applied to.

polAclInterfaceDirection

The direction the ACL is applied to the particular port.

polAclPolicyStatus

Rules for what type of management can apply ACLs to a particular interface. If set to remote, then a Policy Manager via SNMP may change dynamically the ACLs applied to an interface. Note, ACLs applied dynamically are not maintained across system reboot. U ...

polL2FilterNumber

The number of Layer 3 Access Control Lists defined in the SSR.

polL2FilterLastChanged

The time the Access Control List were last changed.

polL2FilterTable

A list of Layer 2 filters.

polL2FilterEntry

An entry containing a layer 2 filter.

polL2FilterIndex

A unique index into the table representing a single filter entry. This value will remain unique and the relationship between the index and the underlying filter is valid until the next reboot.

polL2FilterDesc

A string used to describe the filter. It should contain the creator IP address, and other descriptive information about the filter. It is recommended that names be unique within a given filter type. This object may not be modified if the associated. polL2 ...

polL2FilterType

The types of filters, as explained below. static-entry Based on the restrictions and the presence of source, destination MAC address they can be of three types : source-static-entry - All frames with a source address equal to srcMAC, coming through any of ...

polL2FilterRestrictions

The first 3 restrictions, allow, disallow, force apply when the filterType is static-entry. When polL2FilterType is addressFilter or portAddressLock, this object does not apply. For securePort, the blockIngress, blockEgress values apply. This object may n ...

polL2FilterSrcMacAddr

The source MAC address, which is present in case of a Flow, that has been learned by the switch.

polL2FilterDstMacAddr

The destination MAC address which has been learned. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1).

polL2FilterVlanId

The VLAN the destination MAC address belongs to. The default VLAN is id 1 on SSR. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1).

polL2FilterInPorts

The set of Ports to which this filter applies on input. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1).

polL2FilterOutPorts

The set of ports to which this filter applies on output. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1).

polL2FilterCreationTime

The value of sysUpTime when this filter was made active(1).

polL2FilterStatus

SMIv2 RowStatus control for this table. Use createAndWait or createAndGo to create a filter, use destroy to remove an entry or notInService to disengage a filter without destroying it. A row in the notReady state has not had all the mandatory objects set.

polL2Dot1qVlanStaticTable

A table containing hardware specific VLAN behavior configuration information for VLANs created with the dot1qVlanStaticTable. Configuration information for each VLAN configured into the device by (local or network) management.

polL2Dot1qVlanStaticEntry

An entry containing additional hardware specific objects for a dot1qVlanStaticEntry.

polL2Dot1qVlanStaticProtocols

Specifies the types of traffic that will be forwarded on this VLAN. Protocols not set in this definition will be filtered. The types of protocols supported on this VLAN corresponds to the type option in the CLI command vlan create . If n ...

polL2Dot1qVlanStaticL4Bridging

If this object has a value of false(2), the L4 Bridging feature is not enabled on this VLAN. If this object has a value of true(1), the L4 Bridging feature is enabled for this VLAN. This corresponds to the CLI command vlan enable l4-bridging.

polL4PolicyBasedRoutingEnabled

The state of Policy Based Routing on this network element.

polL4NumRouters

The number of next hop routers currently available.

polL4NextHopTableLastChange

The value of sysUpTime when a row was last added or deleted from polL4NextHopTable.

polL4NextHopTable

A list of next hop IP routers.

polL4NextHopEntry

An entry contains the status of a next hop router.

polL4NextHopRouter

The IP Address of the next hop router flow will be sent to.

polL4NextHopState

The current status of the polL4NextHopRouter. If no entry found when a policy route is activated, then arp for the request the state will be waitingForArp(2). If a reply is found the state will go to macAcquired(3) else noArpReply(4). If NextHop is not lo ...

polL4NextHopPortOfExit

IfIndex of port we learned this router on or else zero if not known.

polL4NextHopMacAddress

MAC Address of next hop router learned from ARP.

polL4NextHopLastChange

The value of sysUpTime when this polL4NextHopState changed.

polL4lowControlTableLastChange

The value of sysUpTime when a row was last added or deleted from polL4lowControlTable.

polL4NumPolicies

The number of policies currently available.

polL4lowControlTable

Contains Control rows that indicate which flows have been redirected. As flows are aged out and recreated, these rules will enforce flow redirection policy.

polL4lowControlEntry

This table is an ordered collection of route policies. For SSR, this maps to the command: ip-policy Name [permit|deny] acl acl-list

polL4PolicyName

A unique name for this flow policy.

polL4PolicySequence

The evaluation order of this object. When two objects have the same value, the value of the instance value decides which is evaluated first. than higher numbers.

polL4PolicyInstance

The sequence of this policy based route. Lower numbers have higher precedence than higher numbers.

polL4PolicyType

Controls if packets are forwarded or not for this policy.

polL4PolicyAction

Define when this policy should be used during normal packet forwarding process.

polL4PolicyMatch

Up to twenty (20) separate ACLs may be defined to match for this policy. This object is mandatory. Use active row from polAclTable.

polL4PolicyNextHops

Up to for IpAddresses may be specified to route data to next. Load balancing If more than one next hop ip address is specified, the default load balancing scheme is round robin. This object is mandatory. Use objects from polL4NextHopTable.

polL4PolicyLoading

When more than one next hop is defined and available, set loading policy here.

polL4PolicyWatch

When True, use icmp echo to actively maintain status of next hop. This is useful to prevent data sinks with static routes.

polL4lowCreationTime

The value of sysUpTime when policy went was created then activated.

polL4lowActiveGates

The number of currently active nexthop gateways.

polL4lowAppliedTimes

The number of times this policy was used.

polL4lowControlStatus

Entries in active state cause a flow to remain programmed with the next hop router specified. If the next hop router goes down, the rowStatus will become inactive. New flows that match this specification will assume this next hop router over any other rou ...

polL4lowLostRouters

The count of times routers were disabled from NextHopTable due to lost contact.

polL4lowControlTableActivates

The count of successful activations of flow control policies made.

polL4lowControlTableActivateFails

The count of unsuccessful flow control policies made.

polL4lowArpMappingChanges

The count of mac to next hop IP address mapping changes affecting policy based route tables.

polL4lowIcmpRedirects

The count of next hop route redirects received that match a policy in the polL4lowControlTable. This can help to determine if bad route policies are in effect.

polL4lowMatchAttempts

The count of total number of policy based flow lookups made against policy based route table.

polGroupV10

A set of managed objects that make up version 1.0 of the SSR Flow Policy MIB.

polGroupV11

A set of managed objects that make up version 1.1 of the SSR Flow Policy MIB.

polGroupV12

A set of managed objects that make up version 1.2 of the SSR Flow Policy MIB.

polGroupV13

A set of managed objects that make up version 1.3 of the SSR Flow Policy MIB.