-- extracted from draft-ietf-ospf-ospfv3-mib-11.txt -- at Thu Aug 17 06:06:54 2006 OSPFV3-MIB-JUNIPER DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, Counter32, Gauge32, Integer32, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF InterfaceIndex FROM IF-MIB InetAddressType, InetAddress, InetAddressPrefixLength FROM INET-ADDRESS-MIB Metric, BigMetric, Status, HelloRange, DesignatedRouterPriority FROM OSPF-MIB -- Juniper specific *** JNX *** jnxOspfv3Experiment -- *** JNX *** FROM JUNIPER-EXPERIMENT-MIB -- *** JNX *** ; jnxOspfv3MIB MODULE-IDENTITY LAST-UPDATED "201103301200Z" -- 30 March 2011 12:00:00 GMT ORGANIZATION "IETF OSPF Working Group" CONTACT-INFO "WG E-Mail: ospf@ietf.org WG Chairs: acee@cisco.com dube.rohit@gmail.com Dan Joyal Nortel 600 Technology Park Drive Billerica, MA 01821, USA djoyal@nortel.com Vishwas Manral IP Infusion Bangalore India vishwas@ipinfusion.com" DESCRIPTION "The MIB module for OSPF version 3. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices." REVISION "200608091200Z" DESCRIPTION -- RFC Editor assigns RFC xxxx "Initial version, published as RFC xxxx" REVISION "201103301200Z" -- 30 March 2011 12:00:00 GMT DESCRIPTION "Deprecating all objects. New mib file rfc5643.mib takes care of these objects." ::= { jnxOspfv3Experiment 1 } -- *** JNX *** -- Texual conventions JnxOspfv3UpToRefreshIntervalTc ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "The values one might be able to configure for variables bounded by the Refresh Interval" SYNTAX Integer32 (1..1800) JnxOspfv3DeadIntRangeTc ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "The range, in seconds, of dead interval value." SYNTAX Integer32 (1..'FFFF'h) JnxOspfv3RouterIdTc ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "A 32-bit, unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses if IPv4 is configured on the router." SYNTAX Unsigned32 (1..4294967295) JnxOspfv3AreaIdTc ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "An OSPFv3 Area Identifier" SYNTAX Unsigned32 (0..'FFFFFFFF'h) JnxOspfv3IfInstIdTc ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "An OSPFv3 interface instance ID" SYNTAX Integer32 (0..255) -- Top-level structure of MIB jnxOspfv3Notifications OBJECT IDENTIFIER ::= { jnxOspfv3MIB 0 } jnxOspfv3Objects OBJECT IDENTIFIER ::= { jnxOspfv3MIB 1 } jnxOspfv3Conformance OBJECT IDENTIFIER ::= { jnxOspfv3MIB 2 } -- OSPFv3 General Variables -- These parameters apply globally to the Router's -- OSPFv3 Process. jnxOspfv3GeneralGroup OBJECT IDENTIFIER ::= { jnxOspfv3Objects 1 } jnxOspfv3RouterId OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS read-write STATUS deprecated DESCRIPTION "A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router." ::= { jnxOspfv3GeneralGroup 1 } jnxOspfv3AdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces." ::= { jnxOspfv3GeneralGroup 2 } jnxOspfv3VersionNumber OBJECT-TYPE SYNTAX INTEGER { version3 (3) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The version number of OSPF for IPv6 is 3." ::= { jnxOspfv3GeneralGroup 3 } jnxOspfv3AreaBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "A flag to note whether this router is an area border router." REFERENCE "OSPF Version 2, Section 3 Splitting the AS into Areas" ::= { jnxOspfv3GeneralGroup 4 } jnxOspfv3ASBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "A flag to note whether this router is configured as an Autonomous System border router." REFERENCE "OSPF Version 2, Section 3.3 Classification of routers" ::= { jnxOspfv3GeneralGroup 5 } jnxOspfv3AsScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of AS-Scope (e.g. AS-External) link state advertisements in the link state database." ::= { jnxOspfv3GeneralGroup 6 } jnxOspfv3AsScopeLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers." ::= { jnxOspfv3GeneralGroup 7 } jnxOspfv3OriginateNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA." ::= { jnxOspfv3GeneralGroup 8 } jnxOspfv3RxNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of link state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements." ::= { jnxOspfv3GeneralGroup 9 } jnxOspfv3ExtLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of External(LS type 0x4005) in the link state database" ::= { jnxOspfv3GeneralGroup 10 } jnxOspfv3ExtAreaLsdbLimit OBJECT-TYPE SYNTAX Integer32 (-1..'7FFFFFFF'h) MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The maximum number of non-default AS-external-LSAs entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. Ospfv3ExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded)." ::= { jnxOspfv3GeneralGroup 11 } jnxOspfv3MulticastExtensions OBJECT-TYPE SYNTAX BITS { intraAreaMulticast(0), interAreaMulticast(1), interAsMulticast(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multicast Extensions to OSPF. If intraAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area multicast routing). If interAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams between OSPFv3 areas (called inter-area multicast routing). If interAsMulticast set, indicates that the router can forward IPv6 multicast datagrams between Autonomous Systems (called inter-AS multicast routing). Only certain combinations of bit settings are allowed, namely: - All bits cleared (no multicasting) - intraAreaMulticast only, - intraAreaMulticast and interAreaMulticast, - intraAreaMulticast and interAsMulticast - intraAreaMulticast, interAreaMulticast and interAsMulticast By default, all bits are cleared." ::= { jnxOspfv3GeneralGroup 12 } jnxOspfv3ExitOverflowInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The number of seconds that, after entering Overflow State, a router will attempt to leave Overflow State. This allows the router to again originate non-default, AS-External-LSAs. When set to 0, the router will not leave Overflow State until restarted." ::= { jnxOspfv3GeneralGroup 13 } jnxOspfv3DemandExtensions OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The router's support for demand routing." REFERENCE "Ospf Version 2, Appendix on Demand Routing" ::= { jnxOspfv3GeneralGroup 14 } jnxOspfv3ReferenceBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Reference bandwidth in kilobits/second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS)" ::= { jnxOspfv3GeneralGroup 15 } jnxOspfv3RestartSupport OBJECT-TYPE SYNTAX INTEGER { none (1), plannedOnly (2), plannedAndUnplanned (3) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The router's support for OSPF Graceful restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts." ::= { jnxOspfv3GeneralGroup 16 } jnxOspfv3RestartInterval OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "Configured OSPF Graceful restart timeout interval." ::= { jnxOspfv3GeneralGroup 17 } jnxOspfv3RestartStatus OBJECT-TYPE SYNTAX INTEGER { notRestarting (1), plannedRestart (2), unplannedRestart (3) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The current status of OSPF Graceful restart capability." ::= { jnxOspfv3GeneralGroup 18 } jnxOspfv3RestartAge OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Remaining time in current OSPF Graceful restart interval." ::= { jnxOspfv3GeneralGroup 19 } jnxOspfv3RestartExitRc OBJECT-TYPE SYNTAX INTEGER { none (1), inProgress (2), completed (3), timedOut (4), topologyChanged (5) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Describes the outcome of the last attempt at a Graceful restart. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change." ::= { jnxOspfv3GeneralGroup 20 } jnxOspfv3NotificationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "If this object is set to true(1), then it enables the generation of OSPFv3 Notifications. If it is set to false(2), these notifications are not generated. Configured values MUST survive an agent reboot." DEFVAL { true } ::= { jnxOspfv3GeneralGroup 21 } -- The OSPFv3 Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0, by definition, is the Backbone Area jnxOspfv3AreaTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3AreaEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Information describing the configured parameters and cumulative statistics of the router's attached areas. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." REFERENCE "OSPF Version 2, Section 6 The Area Data Structure" ::= { jnxOspfv3Objects 2 } jnxOspfv3AreaEntry OBJECT-TYPE SYNTAX JnxOspfv3AreaEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Information describing the configured parameters and cumulative statistics of one of the router's attached areas." INDEX { jnxOspfv3AreaId } ::= { jnxOspfv3AreaTable 1 } JnxOspfv3AreaEntry ::= SEQUENCE { jnxOspfv3AreaId JnxOspfv3AreaIdTc, jnxOspfv3ImportAsExtern INTEGER, jnxOspfv3AreaSpfRuns Counter32, jnxOspfv3AreaBdrRtrCount Gauge32, jnxOspfv3AreaAsBdrRtrCount Gauge32, jnxOspfv3AreaScopeLsaCount Gauge32, jnxOspfv3AreaScopeLsaCksumSum Integer32, jnxOspfv3AreaSummary INTEGER, jnxOspfv3AreaStatus RowStatus, jnxOspfv3StubMetric BigMetric, jnxOspfv3AreaNssaTranslatorRole INTEGER, jnxOspfv3AreaNssaTranslatorState INTEGER, jnxOspfv3AreaNssaTranslatorStabInt Unsigned32, jnxOspfv3AreaNssaTranslatorEvents Counter32, jnxOspfv3AreaStubMetricType INTEGER } jnxOspfv3AreaId OBJECT-TYPE SYNTAX JnxOspfv3AreaIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A 32-bit integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { jnxOspfv3AreaEntry 1 } jnxOspfv3ImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal(1), -- normal area importNoExternal(2), -- stub area importNssa(3) -- not-so-stubby-area } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as NSSA LSAs which have Area-scope" REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" DEFVAL { importExternal } ::= { jnxOspfv3AreaEntry 2 } jnxOspfv3AreaSpfRuns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm." ::= { jnxOspfv3AreaEntry 3 } jnxOspfv3AreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass." ::= { jnxOspfv3AreaEntry 4 } jnxOspfv3AreaAsBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass." ::= { jnxOspfv3AreaEntry 5 } jnxOspfv3AreaScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of Area-Scope link state advertisements in this area's link state database." ::= { jnxOspfv3AreaEntry 6 } jnxOspfv3AreaScopeLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The 32-bit unsigned sum of the Area-Scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." ::= { jnxOspfv3AreaEntry 7 } jnxOspfv3AreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary(1), sendAreaSummary(2) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The variable ospfv3AreaSummary controls the import of Inter-Area LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub or NSSA area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs." DEFVAL { sendAreaSummary } ::= { jnxOspfv3AreaEntry 8 } jnxOspfv3AreaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { jnxOspfv3AreaEntry 9 } jnxOspfv3StubMetric OBJECT-TYPE SYNTAX BigMetric MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The metric value advertised for the default route into Stub and NSSA areas." ::= { jnxOspfv3AreaEntry 10 } jnxOspfv3AreaNssaTranslatorRole OBJECT-TYPE SYNTAX INTEGER { always(1), candidate(2) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Indicates an NSSA Border router's ability to perform NSSA translation of NSSA-LSAs into AS-External-LSAs." DEFVAL { candidate } ::= { jnxOspfv3AreaEntry 11 } jnxOspfv3AreaNssaTranslatorState OBJECT-TYPE SYNTAX INTEGER { enabled(1), elected(2), disabled(3) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates if and how an NSSA Border router is performing NSSA translation of NSSA-LSAs into AS-External-LSA's. When this object is set to enabled, the NSSA Border router's ospfv3AreaNssTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is translating NSSA-LSA's into AS-External-LSA's. When this object is set to disabled, a candidate NSSA Border router is NOT translating NSSA-LSA's into AS-External-LSA's." ::= { jnxOspfv3AreaEntry 12 } jnxOspfv3AreaNssaTranslatorStabInt OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The number of seconds after an elected translator determines its services are no longer required, that it should continue to perform its translation duties." DEFVAL { 40 } ::= { jnxOspfv3AreaEntry 13 } jnxOspfv3AreaNssaTranslatorEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates the number of Translator State changes that have occurred since the last boot-up." ::= { jnxOspfv3AreaEntry 14 } jnxOspfv3AreaStubMetricType OBJECT-TYPE SYNTAX INTEGER { ospfv3Metric (1), -- OSPF Metric comparableCost (2), -- external type 1 nonComparable (3) -- external type 2 } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This variable displays the type of metric advertised as a default route." DEFVAL { ospfv3Metric } ::= { jnxOspfv3AreaEntry 15 } -- OSPFv3 AS-Scope Link State Database -- The Link State Database contains the AS-Scope Link State -- Advertisements from throughout the areas that the -- device is attached to. jnxOspfv3AsLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3AsLsdbEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The OSPFv3 Process's AS-Scope Link State Database. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." ::= { jnxOspfv3Objects 3 } jnxOspfv3AsLsdbEntry OBJECT-TYPE SYNTAX JnxOspfv3AsLsdbEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A single AS-Scope Link State Advertisement." INDEX { jnxOspfv3AsLsdbType, jnxOspfv3AsLsdbRouterId, jnxOspfv3AsLsdbLsid } ::= { jnxOspfv3AsLsdbTable 1 } JnxOspfv3AsLsdbEntry ::= SEQUENCE { jnxOspfv3AsLsdbType Unsigned32, jnxOspfv3AsLsdbRouterId JnxOspfv3RouterIdTc, jnxOspfv3AsLsdbLsid Unsigned32, jnxOspfv3AsLsdbSequence Integer32, jnxOspfv3AsLsdbAge Integer32, jnxOspfv3AsLsdbChecksum Integer32, jnxOspfv3AsLsdbAdvertisement OCTET STRING, jnxOspfv3AsLsdbTypeKnown TruthValue } jnxOspfv3AsLsdbType OBJECT-TYPE SYNTAX Unsigned32(0..'FFFFFFFF'h) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertisement format. AS-Scope LSAs not recognized by the router may be stored in the database." ::= { jnxOspfv3AsLsdbEntry 1 } jnxOspfv3AsLsdbRouterId OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { jnxOspfv3AsLsdbEntry 2 } jnxOspfv3AsLsdbLsid OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics." ::= { jnxOspfv3AsLsdbEntry 3 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. jnxOspfv3AsLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { jnxOspfv3AsLsdbEntry 4 } jnxOspfv3AsLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge -- unless DoNotAge bit is set UNITS "seconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This field is the age of the link state advertisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { jnxOspfv3AsLsdbEntry 5 } jnxOspfv3AsLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { jnxOspfv3AsLsdbEntry 6 } jnxOspfv3AsLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The entire Link State Advertisement, including its header." ::= { jnxOspfv3AsLsdbEntry 7 } jnxOspfv3AsLsdbTypeKnown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates whether the LSA type is recognized by this Router." ::= { jnxOspfv3AsLsdbEntry 8 } -- OSPFv3 Area-Scope Link State Database -- The Link State Database contains the Area-Scope Link State -- Advertisements from throughout the area that the -- device is attached to. jnxOspfv3AreaLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3AreaLsdbEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The OSPFv3 Process's Area-Scope Link State Database. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." ::= { jnxOspfv3Objects 4 } jnxOspfv3AreaLsdbEntry OBJECT-TYPE SYNTAX JnxOspfv3AreaLsdbEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A single Area-Scope Link State Advertisement." INDEX { jnxOspfv3AreaLsdbAreaId, jnxOspfv3AreaLsdbType, jnxOspfv3AreaLsdbRouterId, jnxOspfv3AreaLsdbLsid } ::= { jnxOspfv3AreaLsdbTable 1 } JnxOspfv3AreaLsdbEntry ::= SEQUENCE { jnxOspfv3AreaLsdbAreaId JnxOspfv3AreaIdTc, jnxOspfv3AreaLsdbType Unsigned32, jnxOspfv3AreaLsdbRouterId JnxOspfv3RouterIdTc, jnxOspfv3AreaLsdbLsid Unsigned32, jnxOspfv3AreaLsdbSequence Integer32, jnxOspfv3AreaLsdbAge Integer32, jnxOspfv3AreaLsdbChecksum Integer32, jnxOspfv3AreaLsdbAdvertisement OCTET STRING, jnxOspfv3AreaLsdbTypeKnown TruthValue } jnxOspfv3AreaLsdbAreaId OBJECT-TYPE SYNTAX JnxOspfv3AreaIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The 32-bit identifier of the Area from which the LSA was received." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { jnxOspfv3AreaLsdbEntry 1 } jnxOspfv3AreaLsdbType OBJECT-TYPE SYNTAX Unsigned32(0..'FFFFFFFF'h) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertisement format. Area-Scope LSAs unrecognized by the router are also stored in this database." ::= { jnxOspfv3AreaLsdbEntry 2 } jnxOspfv3AreaLsdbRouterId OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The 32-bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { jnxOspfv3AreaLsdbEntry 3 } jnxOspfv3AreaLsdbLsid OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics." ::= { jnxOspfv3AreaLsdbEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. jnxOspfv3AreaLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { jnxOspfv3AreaLsdbEntry 5 } jnxOspfv3AreaLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge -- unless DoNotAge bit is set UNITS "seconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This field is the age of the link state advertisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { jnxOspfv3AreaLsdbEntry 6 } jnxOspfv3AreaLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { jnxOspfv3AreaLsdbEntry 7 } jnxOspfv3AreaLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The entire Link State Advertisement, including its header." ::= { jnxOspfv3AreaLsdbEntry 8 } jnxOspfv3AreaLsdbTypeKnown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates whether the LSA type is recognized by this Router." ::= { jnxOspfv3AreaLsdbEntry 9 } -- Ospfv3 Link-Scope Link State Database -- The Link State Database contains the Link-Scope Link State -- Advertisements from the links that the -- device is attached to. jnxOspfv3LinkLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3LinkLsdbEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The OSPFv3 Process's Link-Scope Link State Database. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." ::= { jnxOspfv3Objects 5 } jnxOspfv3LinkLsdbEntry OBJECT-TYPE SYNTAX JnxOspfv3LinkLsdbEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A single Link-Scope Link State Advertisement." INDEX { jnxOspfv3LinkLsdbIfIndex, jnxOspfv3LinkLsdbIfInstId, jnxOspfv3LinkLsdbType, jnxOspfv3LinkLsdbRouterId, jnxOspfv3LinkLsdbLsid } ::= { jnxOspfv3LinkLsdbTable 1 } JnxOspfv3LinkLsdbEntry ::= SEQUENCE { jnxOspfv3LinkLsdbIfIndex InterfaceIndex, jnxOspfv3LinkLsdbIfInstId JnxOspfv3IfInstIdTc, jnxOspfv3LinkLsdbType Unsigned32, jnxOspfv3LinkLsdbRouterId JnxOspfv3RouterIdTc, jnxOspfv3LinkLsdbLsid Unsigned32, jnxOspfv3LinkLsdbSequence Integer32, jnxOspfv3LinkLsdbAge Integer32, jnxOspfv3LinkLsdbChecksum Integer32, jnxOspfv3LinkLsdbAdvertisement OCTET STRING, jnxOspfv3LinkLsdbTypeKnown TruthValue } jnxOspfv3LinkLsdbIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The identifier of the link from which the LSA was received." ::= { jnxOspfv3LinkLsdbEntry 1 } jnxOspfv3LinkLsdbIfInstId OBJECT-TYPE SYNTAX JnxOspfv3IfInstIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The identifier of the interface instance from which the LSA was received." ::= { jnxOspfv3LinkLsdbEntry 2 } jnxOspfv3LinkLsdbType OBJECT-TYPE SYNTAX Unsigned32(0..'FFFFFFFF'h) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertisement format. Link-Scope LSAs unrecognized by the router are also stored in this database." ::= { jnxOspfv3LinkLsdbEntry 3 } jnxOspfv3LinkLsdbRouterId OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { jnxOspfv3LinkLsdbEntry 4 } jnxOspfv3LinkLsdbLsid OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics." ::= { jnxOspfv3LinkLsdbEntry 5 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. jnxOspfv3LinkLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { jnxOspfv3LinkLsdbEntry 6 } jnxOspfv3LinkLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge -- unless DoNotAge bit is set UNITS "seconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This field is the age of the link state advertisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { jnxOspfv3LinkLsdbEntry 7 } jnxOspfv3LinkLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { jnxOspfv3LinkLsdbEntry 8 } jnxOspfv3LinkLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The entire Link State Advertisement, including its header." ::= { jnxOspfv3LinkLsdbEntry 9 } jnxOspfv3LinkLsdbTypeKnown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates whether the LSA type is recognized by this Router." ::= { jnxOspfv3LinkLsdbEntry 10 } -- OSPF Host Table -- The Host/Metric Table indicates what hosts are directly -- attached to the Router, and what metrics and types of -- service should be advertised for them. jnxOspfv3HostTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3HostEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The list of Hosts, and their metrics, that the router will advertise as host routes. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." REFERENCE "OSPF Version 2, Appendix C.6 Host route parameters" ::= { jnxOspfv3Objects 6 } jnxOspfv3HostEntry OBJECT-TYPE SYNTAX JnxOspfv3HostEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A metric to be advertised when a given host is reachable." INDEX { jnxOspfv3HostAddressType, jnxOspfv3HostAddress } ::= { jnxOspfv3HostTable 1 } JnxOspfv3HostEntry ::= SEQUENCE { jnxOspfv3HostAddressType InetAddressType, jnxOspfv3HostAddress InetAddress, jnxOspfv3HostMetric Metric, jnxOspfv3HostStatus RowStatus, jnxOspfv3HostAreaID JnxOspfv3AreaIdTc } jnxOspfv3HostAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The address type of ospfv3HostAddress. Only IPv6 addresses without zone index are expected." REFERENCE "OSPF Version 2, Appendix C.6 Host route parameters" ::= { jnxOspfv3HostEntry 1 } jnxOspfv3HostAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (16)) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The IPv6 Address of the Host. Must be a Global address." REFERENCE "OSPF Version 2, Appendix C.6 Host route parameters" ::= { jnxOspfv3HostEntry 2 } jnxOspfv3HostMetric OBJECT-TYPE SYNTAX Metric MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The Metric to be advertised." REFERENCE "OSPF Version 2, Appendix C.6 Host route parameters" ::= { jnxOspfv3HostEntry 3 } jnxOspfv3HostStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { jnxOspfv3HostEntry 4 } jnxOspfv3HostAreaID OBJECT-TYPE SYNTAX JnxOspfv3AreaIdTc MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The Area the Host Entry is to be found within. By default, the area that a subsuming OSPFv3 interface is in, or Area 0" REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { jnxOspfv3HostEntry 5 } -- OSPFv3 Interface Table jnxOspfv3IfTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3IfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" ::= { jnxOspfv3Objects 7 } jnxOspfv3IfEntry OBJECT-TYPE SYNTAX JnxOspfv3IfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3." INDEX { jnxOspfv3IfIndex, jnxOspfv3IfInstId } ::= { jnxOspfv3IfTable 1 } JnxOspfv3IfEntry ::= SEQUENCE { jnxOspfv3IfIndex InterfaceIndex, jnxOspfv3IfInstId JnxOspfv3IfInstIdTc, jnxOspfv3IfAreaId JnxOspfv3AreaIdTc, jnxOspfv3IfType INTEGER, jnxOspfv3IfAdminStat Status, jnxOspfv3IfRtrPriority DesignatedRouterPriority, jnxOspfv3IfTransitDelay JnxOspfv3UpToRefreshIntervalTc, jnxOspfv3IfRetransInterval JnxOspfv3UpToRefreshIntervalTc, jnxOspfv3IfHelloInterval HelloRange, jnxOspfv3IfRtrDeadInterval JnxOspfv3DeadIntRangeTc, jnxOspfv3IfPollInterval Unsigned32, jnxOspfv3IfState INTEGER, jnxOspfv3IfDesignatedRouter JnxOspfv3RouterIdTc, jnxOspfv3IfBackupDesignatedRouter JnxOspfv3RouterIdTc, jnxOspfv3IfEvents Counter32, jnxOspfv3IfStatus RowStatus, jnxOspfv3IfMulticastForwarding INTEGER, jnxOspfv3IfDemand TruthValue, jnxOspfv3IfMetricValue Metric, jnxOspfv3IfLinkScopeLsaCount Gauge32, jnxOspfv3IfLinkLsaCksumSum Integer32, jnxOspfv3IfDemandNbrProbe TruthValue, jnxOspfv3IfDemandNbrProbeRetxLimit Unsigned32, jnxOspfv3IfDemandNbrProbeInterval Unsigned32 } jnxOspfv3IfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured." ::= { jnxOspfv3IfEntry 1 } jnxOspfv3IfInstId OBJECT-TYPE SYNTAX JnxOspfv3IfInstIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Enables multiple interface instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only." ::= { jnxOspfv3IfEntry 2 } jnxOspfv3IfAreaId OBJECT-TYPE SYNTAX JnxOspfv3AreaIdTc MAX-ACCESS read-create STATUS deprecated DESCRIPTION "A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone." DEFVAL { 0 } ::= { jnxOspfv3IfEntry 3 } jnxOspfv3IfType OBJECT-TYPE SYNTAX INTEGER { broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The OSPFv3 interface type." ::= { jnxOspfv3IfEntry 4 } jnxOspfv3IfAdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The OSPFv3 interface's administrative status. The value formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3." DEFVAL { enabled } ::= { jnxOspfv3IfEntry 5 } jnxOspfv3IfRtrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker." DEFVAL { 1 } ::= { jnxOspfv3IfEntry 6 } jnxOspfv3IfTransitDelay OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." DEFVAL { 1 } ::= { jnxOspfv3IfEntry 7 } jnxOspfv3IfRetransInterval OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets." DEFVAL { 5 } ::= { jnxOspfv3IfEntry 8 } jnxOspfv3IfHelloInterval OBJECT-TYPE SYNTAX HelloRange UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network." DEFVAL { 10 } ::= { jnxOspfv3IfEntry 9 } jnxOspfv3IfRtrDeadInterval OBJECT-TYPE SYNTAX JnxOspfv3DeadIntRangeTc UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network." DEFVAL { 40 } ::= { jnxOspfv3IfEntry 10 } jnxOspfv3IfPollInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi-access neighbor." DEFVAL { 120 } ::= { jnxOspfv3IfEntry 11 } jnxOspfv3IfState OBJECT-TYPE SYNTAX INTEGER { down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The OSPFv3 Interface State." ::= { jnxOspfv3IfEntry 12 } jnxOspfv3IfDesignatedRouter OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The Router ID of the Designated Router." ::= { jnxOspfv3IfEntry 13 } jnxOspfv3IfBackupDesignatedRouter OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The Router ID of the Backup Designated Router." ::= { jnxOspfv3IfEntry 14 } jnxOspfv3IfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of times this OSPF interface has changed its state, or an error has occurred." ::= { jnxOspfv3IfEntry 15 } jnxOspfv3IfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { jnxOspfv3IfEntry 16 } jnxOspfv3IfMulticastForwarding OBJECT-TYPE SYNTAX INTEGER { blocked(1), -- no multicast forwarding multicast(2), -- using multicast address unicast(3) -- to each OSPFv3 neighbor } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts. Data link multicasting is not meaningful on point to point and NBMA interfaces, and setting ospfv3MulticastForwarding to 0 effectively disables all multicast forwarding." DEFVAL { blocked } ::= { jnxOspfv3IfEntry 17 } jnxOspfv3IfDemand OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Indicates whether Demand OSPFv3 procedures (hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface." DEFVAL { false } ::= { jnxOspfv3IfEntry 18 } jnxOspfv3IfMetricValue OBJECT-TYPE SYNTAX Metric MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The metric assigned to this interface. The default value of the Metric is Reference Bandwidth / ifSpeed. The value of the reference bandwidth is configured by the ospfv3ReferenceBandwidth object." ::= { jnxOspfv3IfEntry 19 } jnxOspfv3IfLinkScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of Link-Scope link state advertisements in this link's link state database." ::= { jnxOspfv3IfEntry 20 } jnxOspfv3IfLinkLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The 32-bit unsigned sum of the Link-Scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers." ::= { jnxOspfv3IfEntry 21 } jnxOspfv3IfDemandNbrProbe OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default." DEFVAL { false } ::= { jnxOspfv3IfEntry 22 } jnxOspfv3IfDemandNbrProbeRetxLimit OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down." DEFVAL { 10 } ::= { jnxOspfv3IfEntry 23} jnxOspfv3IfDemandNbrProbeInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Defines how often the neighbor will be probed." DEFVAL { 120 } ::= { jnxOspfv3IfEntry 24 } -- OSPFv3 Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the OSPFv3 Process is configured to -- carry on. jnxOspfv3VirtIfTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3VirtIfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Information about this router's virtual interfaces. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." REFERENCE "OSPF Version 2, Appendix C.4 Virtual link parameters" ::= { jnxOspfv3Objects 8 } jnxOspfv3VirtIfEntry OBJECT-TYPE SYNTAX JnxOspfv3VirtIfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Information about a single Virtual Interface." INDEX { jnxOspfv3VirtIfAreaId, jnxOspfv3VirtIfNeighbor } ::= { jnxOspfv3VirtIfTable 1 } JnxOspfv3VirtIfEntry ::= SEQUENCE { jnxOspfv3VirtIfAreaId JnxOspfv3AreaIdTc, jnxOspfv3VirtIfNeighbor JnxOspfv3RouterIdTc, jnxOspfv3VirtIfIndex InterfaceIndex, jnxOspfv3VirtIfInstId JnxOspfv3IfInstIdTc, jnxOspfv3VirtIfTransitDelay JnxOspfv3UpToRefreshIntervalTc, jnxOspfv3VirtIfRetransInterval JnxOspfv3UpToRefreshIntervalTc, jnxOspfv3VirtIfHelloInterval HelloRange, jnxOspfv3VirtIfRtrDeadInterval JnxOspfv3DeadIntRangeTc, jnxOspfv3VirtIfState INTEGER, jnxOspfv3VirtIfEvents Counter32, jnxOspfv3VirtIfStatus RowStatus, jnxOspfv3VirtIfLinkScopeLsaCount Gauge32, jnxOspfv3VirtIfLinkLsaCksumSum Integer32 } jnxOspfv3VirtIfAreaId OBJECT-TYPE SYNTAX JnxOspfv3AreaIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not Area 0" ::= { jnxOspfv3VirtIfEntry 1 } jnxOspfv3VirtIfNeighbor OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { jnxOspfv3VirtIfEntry 2 } jnxOspfv3VirtIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The local interface index assigned to this OSPFv3 virtual interface. It is advertised in Hello's sent over the virtal link and in the router's router-LSAs." ::= { jnxOspfv3VirtIfEntry 3 } jnxOspfv3VirtIfInstId OBJECT-TYPE SYNTAX JnxOspfv3IfInstIdTc MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Specifies the interface instance ID to be used for the virtual interface. This ID has local link significance only." DEFVAL { 0 } ::= { jnxOspfv3VirtIfEntry 4 } jnxOspfv3VirtIfTransitDelay OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." DEFVAL { 1 } ::= { jnxOspfv3VirtIfEntry 5 } jnxOspfv3VirtIfRetransInterval OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets. This value should be well over the expected round-trip time." DEFVAL { 5 } ::= { jnxOspfv3VirtIfEntry 6 } jnxOspfv3VirtIfHelloInterval OBJECT-TYPE SYNTAX HelloRange UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { jnxOspfv3VirtIfEntry 7 } jnxOspfv3VirtIfRtrDeadInterval OBJECT-TYPE SYNTAX JnxOspfv3DeadIntRangeTc UNITS "seconds" MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor." DEFVAL { 60 } ::= { jnxOspfv3VirtIfEntry 8 } jnxOspfv3VirtIfState OBJECT-TYPE SYNTAX INTEGER { down(1), pointToPoint(4) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "ospf virtual interface states. The same encoding as the ospfV3IfTable is used." ::= { jnxOspfv3VirtIfEntry 9 } jnxOspfv3VirtIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of state changes or error events on this Virtual Link" ::= { jnxOspfv3VirtIfEntry 10 } jnxOspfv3VirtIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { jnxOspfv3VirtIfEntry 11 } jnxOspfv3VirtIfLinkScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total number of Link-Scope link state advertisements in this virtual link's link state database." ::= { jnxOspfv3VirtIfEntry 12 } jnxOspfv3VirtIfLinkLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers." ::= { jnxOspfv3VirtIfEntry 13 } -- OSPFv3 Neighbor Table -- The OSPFv3 Neighbor Table describes all neighbors in -- the locality of the subject router. jnxOspfv3NbrTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3NbrEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A table of non-virtual neighbor information." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." ::= { jnxOspfv3Objects 9 } jnxOspfv3NbrEntry OBJECT-TYPE SYNTAX JnxOspfv3NbrEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The information regarding a single neighbor." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" INDEX { jnxOspfv3NbrIfIndex, jnxOspfv3NbrIfInstId, jnxOspfv3NbrRtrId } ::= { jnxOspfv3NbrTable 1 } JnxOspfv3NbrEntry ::= SEQUENCE { jnxOspfv3NbrIfIndex InterfaceIndex, jnxOspfv3NbrIfInstId JnxOspfv3IfInstIdTc, jnxOspfv3NbrRtrId JnxOspfv3RouterIdTc, jnxOspfv3NbrAddressType InetAddressType, jnxOspfv3NbrAddress InetAddress, jnxOspfv3NbrOptions Integer32, jnxOspfv3NbrPriority DesignatedRouterPriority, jnxOspfv3NbrState INTEGER, jnxOspfv3NbrEvents Counter32, jnxOspfv3NbrLsRetransQLen Gauge32, jnxOspfv3NbrHelloSuppressed TruthValue, jnxOspfv3NbrIfId InterfaceIndex, jnxOspfv3NbrRestartHelperStatus INTEGER, jnxOspfv3NbrRestartHelperAge JnxOspfv3UpToRefreshIntervalTc, jnxOspfv3NbrRestartHelperExitRc INTEGER } jnxOspfv3NbrIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The local link ID of the link over which the neighbor can be reached." ::= { jnxOspfv3NbrEntry 1 } jnxOspfv3NbrIfInstId OBJECT-TYPE SYNTAX JnxOspfv3IfInstIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Interface instance over which the neighbor can be reached. This ID has local link significance only." ::= { jnxOspfv3NbrEntry 2 } jnxOspfv3NbrRtrId OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A 32-bit integer uniquely identifying the neighboring router in the Autonomous System." ::= { jnxOspfv3NbrEntry 3 } jnxOspfv3NbrAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected." ::= { jnxOspfv3NbrEntry 4 } jnxOspfv3NbrAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (16)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The IPv6 address of the neighbor associated with the local link." ::= { jnxOspfv3NbrEntry 5 } jnxOspfv3NbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "A Bit Mask corresponding to the neighbor's options field." REFERENCE "OSPF Version 3, Appendix A.2 the Options field" ::= { jnxOspfv3NbrEntry 6 } jnxOspfv3NbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network." ::= { jnxOspfv3NbrEntry 7 } jnxOspfv3NbrState OBJECT-TYPE SYNTAX INTEGER { down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The State of the relationship with this Neighbor." REFERENCE "OSPF Version 2, Section 10.1 Neighbor States" ::= { jnxOspfv3NbrEntry 8 } jnxOspfv3NbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of times this neighbor relationship has changed state, or an error has occurred." ::= { jnxOspfv3NbrEntry 9 } jnxOspfv3NbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The current length of the retransmission queue." ::= { jnxOspfv3NbrEntry 10 } jnxOspfv3NbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { jnxOspfv3NbrEntry 11 } jnxOspfv3NbrIfId OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index." ::= { jnxOspfv3NbrEntry 12 } jnxOspfv3NbrRestartHelperStatus OBJECT-TYPE SYNTAX INTEGER { notHelping (1), helping (2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates whether the router is acting as a Graceful restart helper for the neighbor." ::= { jnxOspfv3NbrEntry 13 } jnxOspfv3NbrRestartHelperAge OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor." ::= { jnxOspfv3NbrEntry 14 } jnxOspfv3NbrRestartHelperExitRc OBJECT-TYPE SYNTAX INTEGER { none (1), inProgress (2), completed (3), timedOut (4), topologyChanged (5) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currentlyly underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change." ::= { jnxOspfv3NbrEntry 15 } -- OSPFv3 Configured Neighbor Table -- The OSPFv3 Configured Neighbor Table describes all configured -- neighbors jnxOspfv3CfgNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3CfgNbrEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A table of configured, non-virtual neighbor information. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" ::= { jnxOspfv3Objects 10 } jnxOspfv3CfgNbrEntry OBJECT-TYPE SYNTAX JnxOspfv3CfgNbrEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The information regarding a single configured neighbor or neighbor discovered by lower-level protocols such as Inverse Neighbor Discovery." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" INDEX { jnxOspfv3CfgNbrIfIndex, jnxOspfv3CfgNbrIfInstId, jnxOspfv3CfgNbrAddressType, jnxOspfv3CfgNbrAddress } ::= { jnxOspfv3CfgNbrTable 1 } JnxOspfv3CfgNbrEntry ::= SEQUENCE { jnxOspfv3CfgNbrIfIndex InterfaceIndex, jnxOspfv3CfgNbrIfInstId JnxOspfv3IfInstIdTc, jnxOspfv3CfgNbrAddressType InetAddressType, jnxOspfv3CfgNbrAddress InetAddress, jnxOspfv3CfgNbrPriority DesignatedRouterPriority, jnxOspfv3CfgNbrStatus RowStatus } jnxOspfv3CfgNbrIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The local link ID of the link over which the neighbor can be reached." ::= { jnxOspfv3CfgNbrEntry 1 } jnxOspfv3CfgNbrIfInstId OBJECT-TYPE SYNTAX JnxOspfv3IfInstIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Interface instance over which the neighbor can be reached. This ID has local link significance only." ::= { jnxOspfv3CfgNbrEntry 2 } jnxOspfv3CfgNbrAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected." ::= { jnxOspfv3CfgNbrEntry 3 } jnxOspfv3CfgNbrAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (16)) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The IPv6 address of the neighbor associated with the local link." ::= { jnxOspfv3CfgNbrEntry 4 } jnxOspfv3CfgNbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network." DEFVAL { 1 } ::= { jnxOspfv3CfgNbrEntry 5 } jnxOspfv3CfgNbrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { jnxOspfv3CfgNbrEntry 6 } -- jnxOspfv3 Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. jnxOspfv3VirtNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3VirtNbrEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A table of virtual neighbor information. Marking this table and its objects deprecated as it is now implemented as a part of RFC 5643." REFERENCE "OSPF Version 2, Section 15 Virtual Links" ::= { jnxOspfv3Objects 11 } jnxOspfv3VirtNbrEntry OBJECT-TYPE SYNTAX JnxOspfv3VirtNbrEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Virtual neighbor information." INDEX { jnxOspfv3VirtNbrArea, jnxOspfv3VirtNbrRtrId } ::= { jnxOspfv3VirtNbrTable 1 } JnxOspfv3VirtNbrEntry ::= SEQUENCE { jnxOspfv3VirtNbrArea JnxOspfv3AreaIdTc, jnxOspfv3VirtNbrRtrId JnxOspfv3RouterIdTc, jnxOspfv3VirtNbrIfIndex InterfaceIndex, jnxOspfv3VirtNbrIfInstId JnxOspfv3IfInstIdTc, jnxOspfv3VirtNbrAddressType InetAddressType, jnxOspfv3VirtNbrAddress InetAddress, jnxOspfv3VirtNbrOptions Integer32, jnxOspfv3VirtNbrState INTEGER, jnxOspfv3VirtNbrEvents Counter32, jnxOspfv3VirtNbrLsRetransQLen Gauge32, jnxOspfv3VirtNbrHelloSuppressed TruthValue, jnxOspfv3VirtNbrIfId InterfaceIndex, jnxOspfv3VirtNbrRestartHelperStatus INTEGER, jnxOspfv3VirtNbrRestartHelperAge JnxOspfv3UpToRefreshIntervalTc, jnxOspfv3VirtNbrRestartHelperExitRc INTEGER } jnxOspfv3VirtNbrArea OBJECT-TYPE SYNTAX JnxOspfv3AreaIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Transit Area Identifier." ::= { jnxOspfv3VirtNbrEntry 1 } jnxOspfv3VirtNbrRtrId OBJECT-TYPE SYNTAX JnxOspfv3RouterIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A 32-bit integer uniquely identifying the neighboring router in the Autonomous System." ::= { jnxOspfv3VirtNbrEntry 2 } jnxOspfv3VirtNbrIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The local interface ID for the virtual link over which the neighbor can be reached." ::= { jnxOspfv3VirtNbrEntry 3 } jnxOspfv3VirtNbrIfInstId OBJECT-TYPE SYNTAX JnxOspfv3IfInstIdTc MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The interface instance for the virtual link over which the neighbor can be reached." ::= { jnxOspfv3VirtNbrEntry 4 } jnxOspfv3VirtNbrAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The address type of ospfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected." ::= { jnxOspfv3VirtNbrEntry 5 } jnxOspfv3VirtNbrAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (16)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The IPv6 address advertised by this Virtual Neighbor. It must be a Global scope address." ::= { jnxOspfv3VirtNbrEntry 6 } jnxOspfv3VirtNbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "A Bit Mask corresponding to the neighbor's options field." REFERENCE "OSPF Version 3, Appendix A.2 the Options field" ::= { jnxOspfv3VirtNbrEntry 7 } jnxOspfv3VirtNbrState OBJECT-TYPE SYNTAX INTEGER { down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The state of the Virtual Neighbor Relationship." ::= { jnxOspfv3VirtNbrEntry 8 } jnxOspfv3VirtNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of times this virtual link has changed its state, or an error has occurred." ::= { jnxOspfv3VirtNbrEntry 9 } jnxOspfv3VirtNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The current length of the retransmission queue." ::= { jnxOspfv3VirtNbrEntry 10 } jnxOspfv3VirtNbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { jnxOspfv3VirtNbrEntry 11 } jnxOspfv3VirtNbrIfId OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface ID." ::= { jnxOspfv3VirtNbrEntry 12 } jnxOspfv3VirtNbrRestartHelperStatus OBJECT-TYPE SYNTAX INTEGER { notHelping (1), helping (2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Indicates whether the router is acting as a Graceful restart helper for the neighbor." ::= { jnxOspfv3VirtNbrEntry 13 } jnxOspfv3VirtNbrRestartHelperAge OBJECT-TYPE SYNTAX JnxOspfv3UpToRefreshIntervalTc UNITS "seconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor." ::= { jnxOspfv3VirtNbrEntry 14 } jnxOspfv3VirtNbrRestartHelperExitRc OBJECT-TYPE SYNTAX INTEGER { none (1), inProgress (2), completed (3), timedOut (4), topologyChanged (5) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change." ::= { jnxOspfv3VirtNbrEntry 15 } -- -- The OSPFv3 Area Aggregate Table -- jnxOspfv3AreaAggregateTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxOspfv3AreaAggregateEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one. Marking this table and its objects deprecated as it is now implemented as part of RFC 5643." ::= { jnxOspfv3Objects 12 } jnxOspfv3AreaAggregateEntry OBJECT-TYPE SYNTAX JnxOspfv3AreaAggregateEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" INDEX { jnxOspfv3AreaAggregateAreaID, jnxOspfv3AreaAggregateAreaLsdbType, jnxOspfv3AreaAggregatePrefixType, jnxOspfv3AreaAggregatePrefix, jnxOspfv3AreaAggregatePrefixLength } ::= { jnxOspfv3AreaAggregateTable 1 } JnxOspfv3AreaAggregateEntry ::= SEQUENCE { jnxOspfv3AreaAggregateAreaID JnxOspfv3AreaIdTc, jnxOspfv3AreaAggregateAreaLsdbType INTEGER, jnxOspfv3AreaAggregatePrefixType InetAddressType, jnxOspfv3AreaAggregatePrefix InetAddress, jnxOspfv3AreaAggregatePrefixLength InetAddressPrefixLength, jnxOspfv3AreaAggregateStatus RowStatus, jnxOspfv3AreaAggregateEffect INTEGER, jnxOspfv3AreaAggregateRouteTag INTEGER } jnxOspfv3AreaAggregateAreaID OBJECT-TYPE SYNTAX JnxOspfv3AreaIdTc MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Area the Address Aggregate is to be found within." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { jnxOspfv3AreaAggregateEntry 1 } jnxOspfv3AreaAggregateAreaLsdbType OBJECT-TYPE SYNTAX INTEGER { interAreaPrefixLsa(8195), -- 0x2003 nssaExternalLsa(8199) -- 0x2007 } MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Aggregate applies to." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { jnxOspfv3AreaAggregateEntry 2 } jnxOspfv3AreaAggregatePrefixType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The prefix type of ospfv3AreaAggregatePrefix. Only IPv6 addresses are expected." ::= { jnxOspfv3AreaAggregateEntry 4 } jnxOspfv3AreaAggregatePrefix OBJECT-TYPE SYNTAX InetAddress (SIZE (0..16)) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The IPv6 Prefix." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { jnxOspfv3AreaAggregateEntry 5 } jnxOspfv3AreaAggregatePrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (3..128) UNITS "bits" MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The length of the prefix (in bits). A prefix can not be shorter than 3 bits." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { jnxOspfv3AreaAggregateEntry 6 } jnxOspfv3AreaAggregateStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { jnxOspfv3AreaAggregateEntry 7 } jnxOspfv3AreaAggregateEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching(1), doNotAdvertiseMatching(2) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (advertiseMatching), or result in the prefix not being advertised at all outside the area." DEFVAL { advertiseMatching } ::= { jnxOspfv3AreaAggregateEntry 8 } jnxOspfv3AreaAggregateRouteTag OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This tag is advertised only in the summarized As-External LSA when summarizing from NSSA-LSA's to AS-External-LSA's." DEFVAL { 0 } ::= { jnxOspfv3AreaAggregateEntry 9 } -- The jnxOspfv3 Notification Table -- The jnxOspfv3 Notification Table records fields that are -- required for notifications jnxOspfv3NotificationEntry OBJECT IDENTIFIER ::= { jnxOspfv3Objects 13 } jnxOspfv3ConfigErrorType OBJECT-TYPE SYNTAX INTEGER { badVersion (1), areaMismatch (2), unknownNbmaNbr (3), -- Router is DR eligible unknownVirtualNbr (4), helloIntervalMismatch (5), deadIntervalMismatch (6), optionMismatch (7), mtuMismatch (8), duplicateRouterId (9), noError (10) } MAX-ACCESS accessible-for-notify STATUS deprecated DESCRIPTION "Potential types of configuration conflicts. Used by the ospfv3ConfigError and ospfv3ConfigVirtError notifications. When the last value of a notification using this object is needed, but no notifications of that type have been sent, this value pertaining to this object should be returned as noError" ::= { jnxOspfv3NotificationEntry 1 } jnxOspfv3PacketType OBJECT-TYPE SYNTAX INTEGER { hello (1), dbDescript (2), lsReq (3), lsUpdate (4), lsAck (5), nullPacket (6) } MAX-ACCESS accessible-for-notify STATUS deprecated DESCRIPTION "OSPFv3 packet types. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as nullPacket" ::= { jnxOspfv3NotificationEntry 2 } jnxOspfv3PacketSrc OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS deprecated DESCRIPTION "The IPv6 address of an inbound packet that cannot be identified by a neighbor instance. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as 0 Only IPv6 addresses without zone index are expected." ::= { jnxOspfv3NotificationEntry 3 } -- Notification definitions jnxOspfv3VirtIfStateChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3VirtIfState -- The new state } STATUS deprecated DESCRIPTION "An ospfv3VirtIfStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual interface. This notification should be generated when the interface state regresses (e.g., goes from Point-to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point)." ::= { jnxOspfv3Notifications 1 } jnxOspfv3NbrStateChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of -- the notification jnxOspfv3NbrState -- The new state } STATUS deprecated DESCRIPTION "An ospfv3NbrStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When an neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the notification should be generated by the designated router. A designated router transitioning to Down will be noted by ospfIfStateChange." ::= { jnxOspfv3Notifications 2 } jnxOspfv3VirtNbrStateChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3VirtNbrState -- The new state } STATUS deprecated DESCRIPTION "An ospfv3VirtNbrStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full)." ::= { jnxOspfv3Notifications 3 } jnxOspfv3IfConfigError NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3IfState, -- State of the interface jnxOspfv3PacketSrc, -- IPv6 address of source jnxOspfv3ConfigErrorType, -- Type of error jnxOspfv3PacketType -- Type of packet } STATUS deprecated DESCRIPTION "An ospfv3IfConfigError notification signifies that a packet has been received on a non-virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming." ::= { jnxOspfv3Notifications 4 } jnxOspfv3VirtIfConfigError NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3VirtIfState, -- State of the interface jnxOspfv3ConfigErrorType, -- Type of error jnxOspfv3PacketType } STATUS deprecated DESCRIPTION "An ospfv3VirtIfConfigError notification signifies that a packet has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming." ::= { jnxOspfv3Notifications 5 } jnxOspfv3IfRxBadPacket NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3IfState, -- State of the interface jnxOspfv3PacketSrc, -- The source IPv6 address jnxOspfv3PacketType -- Type of packet } STATUS deprecated DESCRIPTION "An ospfv3IfRxBadPacket notification signifies that an ospfv3 packet that cannot be parsed has been received on a non-virtual interface." ::= { jnxOspfv3Notifications 6 } jnxOspfv3VirtIfRxBadPacket NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3VirtIfState, -- State of the interface jnxOspfv3PacketType -- Type of packet } STATUS deprecated DESCRIPTION "An ospfv3VirtIfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a virtual interface." ::= { jnxOspfv3Notifications 7 } jnxOspfv3LsdbOverflow NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3ExtAreaLsdbLimit -- Limit on External LSAs } STATUS deprecated DESCRIPTION "An ospfv3LsdbOverflow notification signifies that the number of LSAs in the router's link-state database has exceeded ospfv3ExtAreaLsdbLimit." ::= { jnxOspfv3Notifications 8 } jnxOspfv3LsdbApproachingOverflow NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3ExtAreaLsdbLimit } STATUS deprecated DESCRIPTION "An ospfv3LsdbApproachingOverflow notification signifies that the number of LSAs in the router's link-state database has exceeded ninety percent of ospfv3ExtAreaLsdbLimit." ::= { jnxOspfv3Notifications 9 } jnxOspfv3IfStateChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3IfState -- The new state } STATUS deprecated DESCRIPTION "An ospfv3IfStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 interface. This notification should be generated when the interface state regresses (e.g., goes from Dr to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, Dr, or Backup)." ::= { jnxOspfv3Notifications 10 } jnxOspfv3NssaTranslatorStatusChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3AreaNssaTranslatorState -- new state } STATUS deprecated DESCRIPTION "An ospfv3NssaTranslatorStatusChange notification indicates that there has been a change in the router's ability to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs. This notification should be generated when the Translator Status transitions from or to any defined status on a per area basis." ::= { jnxOspfv3Notifications 11 } jnxOspfv3RestartStatusChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3RestartStatus, -- new status jnxOspfv3RestartInterval, jnxOspfv3RestartExitRc } STATUS deprecated DESCRIPTION "An ospfv3RestartStatusChange notification signifies that there has been a change in the graceful restart state for the router. This notification should be generated when the router restart status changes." ::= { jnxOspfv3Notifications 12 } jnxOspfv3NbrRestartHelperStatusChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3NbrRestartHelperStatus, -- new status jnxOspfv3NbrRestartHelperAge, jnxOspfv3NbrRestartHelperExitRc } STATUS deprecated DESCRIPTION "An ospfv3NbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the neighbor. This notification should be generated when the neighbor restart helper status transitions for a neighbor." ::= { jnxOspfv3Notifications 13 } jnxOspfv3VirtNbrRestartHelperStatusChange NOTIFICATION-TYPE OBJECTS { jnxOspfv3RouterId, -- The originator of the notification jnxOspfv3VirtNbrRestartHelperStatus, -- new status jnxOspfv3VirtNbrRestartHelperAge, jnxOspfv3VirtNbrRestartHelperExitRc } STATUS deprecated DESCRIPTION "An ospfv3VirtNbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the virtual neighbor. This notification should be generated when the virtual neighbor restart helper status transitions for a virtual neighbor." ::= { jnxOspfv3Notifications 14 } -- conformance information jnxOspfv3Groups OBJECT IDENTIFIER ::= { jnxOspfv3Conformance 1 } jnxOspfv3Compliances OBJECT IDENTIFIER ::= { jnxOspfv3Conformance 2 } -- compliance statements jnxOspfv3Compliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement" MODULE -- this module MANDATORY-GROUPS { jnxOspfv3BasicGroup, jnxOspfv3AreaGroup, jnxOspfv3IfGroup, jnxOspfv3VirtIfGroup, jnxOspfv3NbrGroup, jnxOspfv3CfgNbrGroup, jnxOspfv3VirtNbrGroup, jnxOspfv3AreaAggregateGroup, jnxOspfv3NotificationObjectGroup, jnxOspfv3NotificationGroup } GROUP jnxOspfv3AsLsdbGroup DESCRIPTION "This group is required for OSPFv3 systems that display their AS-scope link state database." GROUP jnxOspfv3AreaLsdbGroup DESCRIPTION "This group is required for OSPFv3 systems that display their Area-scope link state database." GROUP jnxOspfv3LinkLsdbGroup DESCRIPTION "This group is required for OSPFv3 systems that display their Link-scope link state database." GROUP jnxOspfv3HostGroup DESCRIPTION "This group is required for OSPFv3 systems that support attached hosts." OBJECT jnxOspfv3NbrAddressType SYNTAX InetAddressType { ipv6(2) } DESCRIPTION "An implementation is only required to support IPv6 address without zone index." OBJECT jnxOspfv3VirtNbrAddressType SYNTAX InetAddressType { ipv6(2) } DESCRIPTION "An implementation is only required to support IPv6 address without zone index." ::= { jnxOspfv3Compliances 1 } -- units of conformance jnxOspfv3BasicGroup OBJECT-GROUP OBJECTS { jnxOspfv3RouterId, jnxOspfv3AdminStat, jnxOspfv3VersionNumber, jnxOspfv3AreaBdrRtrStatus, jnxOspfv3ASBdrRtrStatus, jnxOspfv3AsScopeLsaCount, jnxOspfv3AsScopeLsaCksumSum, jnxOspfv3OriginateNewLsas, jnxOspfv3RxNewLsas, jnxOspfv3ExtLsaCount, jnxOspfv3ExtAreaLsdbLimit, jnxOspfv3MulticastExtensions, jnxOspfv3ExitOverflowInterval, jnxOspfv3DemandExtensions, jnxOspfv3ReferenceBandwidth, jnxOspfv3RestartSupport, jnxOspfv3RestartInterval, jnxOspfv3RestartStatus, jnxOspfv3RestartAge, jnxOspfv3RestartExitRc, jnxOspfv3NotificationEnable } STATUS deprecated DESCRIPTION "These objects are used for managing/monitoring OSPFv3 global parameters." ::= { jnxOspfv3Groups 1 } jnxOspfv3AreaGroup OBJECT-GROUP OBJECTS { jnxOspfv3ImportAsExtern, jnxOspfv3AreaSpfRuns, jnxOspfv3AreaBdrRtrCount, jnxOspfv3AreaAsBdrRtrCount, jnxOspfv3AreaScopeLsaCount, jnxOspfv3AreaScopeLsaCksumSum, jnxOspfv3AreaSummary, jnxOspfv3AreaStatus, jnxOspfv3StubMetric, jnxOspfv3AreaNssaTranslatorRole, jnxOspfv3AreaNssaTranslatorState, jnxOspfv3AreaNssaTranslatorStabInt, jnxOspfv3AreaNssaTranslatorEvents, jnxOspfv3AreaStubMetricType } STATUS deprecated DESCRIPTION "These objects are used for ospfv3 systems supporting areas." ::= { jnxOspfv3Groups 2 } jnxOspfv3AsLsdbGroup OBJECT-GROUP OBJECTS { jnxOspfv3AsLsdbSequence, jnxOspfv3AsLsdbAge, jnxOspfv3AsLsdbChecksum, jnxOspfv3AsLsdbAdvertisement, jnxOspfv3AsLsdbTypeKnown } STATUS deprecated DESCRIPTION "These objects are used for ospfv3 systems that display their AS-scope link state database." ::= { jnxOspfv3Groups 3 } jnxOspfv3AreaLsdbGroup OBJECT-GROUP OBJECTS { jnxOspfv3AreaLsdbSequence, jnxOspfv3AreaLsdbAge, jnxOspfv3AreaLsdbChecksum, jnxOspfv3AreaLsdbAdvertisement, jnxOspfv3AreaLsdbTypeKnown } STATUS deprecated DESCRIPTION "These objects are used for OSPFv3 systems that display their Area-scope link state database." ::= { jnxOspfv3Groups 4 } jnxOspfv3LinkLsdbGroup OBJECT-GROUP OBJECTS { jnxOspfv3LinkLsdbSequence, jnxOspfv3LinkLsdbAge, jnxOspfv3LinkLsdbChecksum, jnxOspfv3LinkLsdbAdvertisement, jnxOspfv3LinkLsdbTypeKnown } STATUS deprecated DESCRIPTION "These objects are used for OSPFv3 systems that display their Link-scope link state database." ::= { jnxOspfv3Groups 5 } jnxOspfv3HostGroup OBJECT-GROUP OBJECTS { jnxOspfv3HostMetric, jnxOspfv3HostStatus, jnxOspfv3HostAreaID } STATUS deprecated DESCRIPTION "These objects are used for OSPFv3 systems that support attached hosts." ::= { jnxOspfv3Groups 6 } jnxOspfv3IfGroup OBJECT-GROUP OBJECTS { jnxOspfv3IfAreaId, jnxOspfv3IfType, jnxOspfv3IfAdminStat, jnxOspfv3IfRtrPriority, jnxOspfv3IfTransitDelay, jnxOspfv3IfRetransInterval, jnxOspfv3IfHelloInterval, jnxOspfv3IfRtrDeadInterval, jnxOspfv3IfPollInterval, jnxOspfv3IfState, jnxOspfv3IfDesignatedRouter, jnxOspfv3IfBackupDesignatedRouter, jnxOspfv3IfEvents, jnxOspfv3IfStatus, jnxOspfv3IfMulticastForwarding, jnxOspfv3IfDemand, jnxOspfv3IfMetricValue, jnxOspfv3IfLinkScopeLsaCount, jnxOspfv3IfLinkLsaCksumSum, jnxOspfv3IfDemandNbrProbe, jnxOspfv3IfDemandNbrProbeRetxLimit, jnxOspfv3IfDemandNbrProbeInterval } STATUS deprecated DESCRIPTION "These interface objects used for managing/monitoring OSPFv3 interfaces." ::= { jnxOspfv3Groups 7 } jnxOspfv3VirtIfGroup OBJECT-GROUP OBJECTS { jnxOspfv3VirtIfIndex, jnxOspfv3VirtIfInstId, jnxOspfv3VirtIfTransitDelay, jnxOspfv3VirtIfRetransInterval, jnxOspfv3VirtIfHelloInterval, jnxOspfv3VirtIfRtrDeadInterval, jnxOspfv3VirtIfState, jnxOspfv3VirtIfEvents, jnxOspfv3VirtIfStatus, jnxOspfv3VirtIfLinkScopeLsaCount, jnxOspfv3VirtIfLinkLsaCksumSum } STATUS deprecated DESCRIPTION "These virtual interface objects are used for managing/monitoring OSPFv3 virtual interfaces." ::= { jnxOspfv3Groups 8 } jnxOspfv3NbrGroup OBJECT-GROUP OBJECTS { jnxOspfv3NbrAddressType, jnxOspfv3NbrAddress, jnxOspfv3NbrOptions, jnxOspfv3NbrPriority, jnxOspfv3NbrState, jnxOspfv3NbrEvents, jnxOspfv3NbrLsRetransQLen, jnxOspfv3NbrHelloSuppressed, jnxOspfv3NbrIfId, jnxOspfv3NbrRestartHelperStatus, jnxOspfv3NbrRestartHelperAge, jnxOspfv3NbrRestartHelperExitRc } STATUS deprecated DESCRIPTION "These neighbor objects are used for managing/monitoring OSPFv3 neighbors." ::= { jnxOspfv3Groups 9 } jnxOspfv3CfgNbrGroup OBJECT-GROUP OBJECTS { jnxOspfv3CfgNbrPriority, jnxOspfv3CfgNbrStatus } STATUS deprecated DESCRIPTION "These configured neighbor objects are used for managing/monitoring ospfv3 configured neighbors." ::= { jnxOspfv3Groups 10 } jnxOspfv3VirtNbrGroup OBJECT-GROUP OBJECTS { jnxOspfv3VirtNbrIfIndex, jnxOspfv3VirtNbrIfInstId, jnxOspfv3VirtNbrAddressType, jnxOspfv3VirtNbrAddress, jnxOspfv3VirtNbrOptions, jnxOspfv3VirtNbrState, jnxOspfv3VirtNbrEvents, jnxOspfv3VirtNbrLsRetransQLen, jnxOspfv3VirtNbrHelloSuppressed, jnxOspfv3VirtNbrIfId, jnxOspfv3VirtNbrRestartHelperStatus, jnxOspfv3VirtNbrRestartHelperAge, jnxOspfv3VirtNbrRestartHelperExitRc } STATUS deprecated DESCRIPTION "These virtual neighbor objects are used for managing/monitoring OSPFv3 virtual neighbors." ::= { jnxOspfv3Groups 11 } jnxOspfv3AreaAggregateGroup OBJECT-GROUP OBJECTS { jnxOspfv3AreaAggregateStatus, jnxOspfv3AreaAggregateEffect, jnxOspfv3AreaAggregateRouteTag } STATUS deprecated DESCRIPTION "These area aggregate objects used required for aggregating OSPFv3 prefixes for summarization across areas." ::= { jnxOspfv3Groups 12 } jnxOspfv3NotificationObjectGroup OBJECT-GROUP OBJECTS { jnxOspfv3ConfigErrorType, jnxOspfv3PacketType, jnxOspfv3PacketSrc } STATUS deprecated DESCRIPTION "These objects are used to record notification parameters" ::= { jnxOspfv3Groups 13 } jnxOspfv3NotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { jnxOspfv3VirtIfStateChange, jnxOspfv3NbrStateChange, jnxOspfv3VirtNbrStateChange, jnxOspfv3IfConfigError, jnxOspfv3VirtIfConfigError, jnxOspfv3IfRxBadPacket, jnxOspfv3VirtIfRxBadPacket, jnxOspfv3LsdbOverflow, jnxOspfv3LsdbApproachingOverflow, jnxOspfv3IfStateChange, jnxOspfv3NssaTranslatorStatusChange, jnxOspfv3RestartStatusChange, jnxOspfv3NbrRestartHelperStatusChange, jnxOspfv3VirtNbrRestartHelperStatusChange } STATUS deprecated DESCRIPTION "This group is used for OSPFv3 notifications" ::= { jnxOspfv3Groups 14 } END -- -- Copyright (C) The Internet Society (2006). -- -- This document is subject to the rights, licenses and restrictions -- contained in BCP 78, and except as set forth therein, the authors -- retain all their rights. -- -- This document and the information contained herein are provided on an -- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS -- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, -- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE -- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. -- --