The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for idle timer
- lapb Admn T4 Idle Timer
- lapbAdmnT4IdleTimer 1.3.6.1.2.1.10.16.1.1.12 (defined in rfc1381)
The T4 timer for this interface. This specifies the maximum time in Milliseconds to allow without frames being exchanged on the data link. A value of 2147483647 indicates no idle timer is being kept. - lapb Operation T4 Idle Timer
- lapbOperT4IdleTimer 1.3.6.1.2.1.10.16.2.1.12 (defined in rfc1381)
The current T4 timer for this interface. This specifies the maximum time in Milliseconds to allow without frames being exchanged on the data link. A value of 2147483647 indicates no idle timer is being kept. - ipx Interface SVC Idle Timer
- ipxInterfaceSVCIdleTimer 1.3.6.1.4.1.173.7.4.3.2.6.1.28 (defined in netlink-specific-mib)
.. Valid only for type X.25 - Net Link If Ip SVC Idle Timer
- nlIfIpSVCIdleTimer 1.3.6.1.4.1.173.7.4.4.1.1.18 (defined in netlink-specific-mib)
no traffic before the connection is cleared. This object is only valid when the interface type is X.25. - Cisco's Airline protocol support Remote Peer Idle Timer
- alpsRemPeerIdleTimer 1.3.6.1.4.1.9.9.95.1.2.2.1.8 (defined in CISCO-ALPS-MIB)
The TCP session with the peer will be closed if there is no activity for alpsInactiveTimer seconds. This is valid only for dynamic circuits - Cisco's Airline protocol support Remote Peer Configuration Idle Timer
- alpsRemPeerCfgIdleTimer 1.3.6.1.4.1.9.9.95.1.2.3.1.5 (defined in CISCO-ALPS-MIB)
The configured idle timer for a dynamic activation peer. - Cisco's Airline protocol support Remote Peer Connection Idle Timer
- alpsRemPeerConnIdleTimer 1.3.6.1.4.1.9.9.95.1.2.4.1.13 (defined in CISCO-ALPS-MIB)
A dynamic activation ALPS peer connection will be closed if zero peer data messages are sent or received for a length of time greater than or equal to this timer. - Cisco's Airline protocol support Circuit P1024 Idle Timer
- alpsCktP1024IdleTimer 1.3.6.1.4.1.9.9.95.1.3.3.1.4 (defined in CISCO-ALPS-MIB)
If there is no traffic on a dynamic ALPS circuit for this interval, it will be cleared. - Cisco Ggsn Idle Pdp Purge Timer
- cGgsnIdlePdpPurgeTimer 1.3.6.1.4.1.9.9.240.1.3.2 (defined in CISCO-GGSN-MIB)
This object specifies the time that the GGSN waits before purging idle PDP contexts. A value '0' will disable the purge timer. - Cisco GPRS Access Point Idle Pdp Purge Timer
- cgprsAccPtIdlePdpPurgeTimer 1.3.6.1.4.1.9.9.183.1.1.1.1.20 (defined in CISCO-GPRS-ACC-PT-MIB)
This object indicates maximum idle connection time allowed to the PDP or Bearer context before termination of the GTP session. A value of 0 means session idle timer is not used. - Frame Relay Svc Dlcmi Idle Timer
- frSvcDlcmiIdleTimer 1.3.6.1.2.1.10.32.7.1.1.1.12 (defined in ibm-frsvc)
This is the maximum time allowed without any frames being exchanged. The default for this timer is 30 seconds. - slb Virtual Idle Timer
- slbVirtualIdleTimer 1.3.6.1.4.1.9.9.161.1.4.1.1.11 (defined in CISCO-SLB-MIB)
The amount of time this SLB entity will maintain connection information in the absence of packet activity for a connection. When the service is configured as 'gtp', this is the amount of time the SLB entity will forward SGSN retries for a SLB session to the same GGSN - slb Cluster Idle Timer
- slbClusterIdleTimer 1.3.6.1.4.1.6486.800.1.2.1.20.1.1.2.1.1.10 (defined in ALCATEL-IND1-SLB-MIB)
The maximum delay with no activity a client is kept attached to a real server. - appn Rtp Idle Timer
- appnRtpIdleTimer (defined in Nortel-Magellan-Passport-AppnMIB)
The idle timer of this High Performance Routing-Rapid Transport Protocol pipe (in seconds) - Frame Relay Uni Sig Idle Probe Timer
- frUniSigIdleProbeTimer (defined in Nortel-Magellan-Passport-FrameRelayUniMIB)
This attribute specifies the time period in milliseconds the link will be permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, the network's side link layer polls its peer for status. The value set for idleProbeTimer must be greater than the value set for ackTimer. - gsm Cs V42 T403 Idle Probe Timer
- gsmCsV42T403IdleProbeTimer (defined in Nortel-Magellan-Passport-GsmIwfMIB)
This attribute specifies the maximum amount of time that the IWF allows to elapse without frames being exchanged. The link is permitted to remain idle with no frames being exchanged on the data link. Upon expiry of this timer, the IWF polls its peer for status. Since information about the T403 timer is not carried in the Exchange Identification (XID) negotiations at call setup time, both sides operate with different timer values. Changes to this attribute do not effect existing calls. - mpanl Sig Idle Probe Timer
- mpanlSigIdleProbeTimer (defined in Nortel-Magellan-Passport-MpaNetworkLinkMIB)
This attribute specifies the time period in milliseconds the link will be permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, the network's side link layer polls its peer for status. The value set for idleProbeTimer must be greater than the value set for ackTimer. - tdma Cs V42 T403 Idle Probe Timer
- tdmaCsV42T403IdleProbeTimer (defined in Nortel-Magellan-Passport-TdmaIwfMIB)
This attribute specifies the maximum amount of time that the IWF allows to elapse without frames being exchanged. The link is permitted to remain idle with no frames being exchanged on the data link. Upon expiry of this timer, the IWF polls its peer for status. Since information about the T403 timer is not carried in the Exchange Identification (XID) negotiations at call setup time, both sides operate with different timer values. Changes to this attribute do not affect existing calls. - x25 Dte Lapb T4 Idle Probe Timer
- x25DteLapbT4IdleProbeTimer 1.3.6.1.4.1.562.2.4.1.90.5.10.1.8 (defined in Nortel-Magellan-Passport-X25DteMIB)
This attribute specifies the time period in milliseconds the link will be permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, LAPB will poll its peer for status. The value set for t4 idle probe timer must be greater than the value set for the t1 ack timer.
