The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for modem connection
- Modem CC Connection Fail Reason
- mdmCCConnectionFailReason 1.3.6.1.2.1.38.1.7.1.6 (defined in rfc1696)
Indicates the reason that the last connection or attempt failed. The meaning of each reason code is explained below. unknown: This code means the failure reason is unknown or there has been no previous call. other: This code used when no other code is applicable. Additional vendor information may be available elsewhere. managementCommand: A management command terminated the call. These commands include escaping to command mode, initiating dialing, restoring lines, and disconnecting. inactivityTimeout: The call was terminated because it was inactive for at the minimum duration specified. mnpIncompatibility: The modems are unable to resolve MNP protocol differences. protocolError: An error occured in one of protocol in use. Further information is required to determine in which protocol the error occurred, and the exact nature of the error. powerLoss: The modem lost power and disconnected the call. equipmentFailure: The modem equipment failed. dtrDrop: DTR has been turned off while the modem is to disconnect on DTR drop. (Ref: V.58 cct108TurnedOff) noDialTone: If the modem is to monitor for call progress tones, but the modem has failed to detect dial tone while attempting to dial a number. lineBusy: Busy signal is detected while busy signal detection is enabled, or while the 'W' or '@' dial modifier is used. (Ref: V.58 engagedTone) noAnswer: The call was not answered. voiceDetected: A voice was detected on the call. carrierLost: Indicates that the modem has disconnected due to detection of loss of carrier. In TIA-602, the S10 register determines the time that loss of carrier must be detected before the modem disconnects. trainingFailed: Indicates that the modems did not successfully train and reach data mode on the previous connection. faxDetected: A fax was detected on the call. - Modem Statistics Incoming Connection Failures
- mdmStatsIncomingConnectionFailures 1.3.6.1.2.1.38.1.12.1.2 (defined in rfc1696)
The number of incoming connection requests that this modem answered in which it could not train with the other DCE. - Modem Statistics Incoming Connection Completions
- mdmStatsIncomingConnectionCompletions 1.3.6.1.2.1.38.1.12.1.3 (defined in rfc1696)
The number of incoming connection requests that this modem answered and successfully trained with the other DCE. - Modem Statistics Outgoing Connection Failures
- mdmStatsOutgoingConnectionFailures 1.3.6.1.2.1.38.1.12.1.5 (defined in rfc1696)
The number of outgoing calls from this modem which sucessfully went off hook and dialed, in which it could not train with the other DCE. - Modem Statistics Outgoing Connection Completions
- mdmStatsOutgoingConnectionCompletions 1.3.6.1.2.1.38.1.12.1.6 (defined in rfc1696)
The number of outgoing calls from this modem which resulted in successfully training with the other DCE. - hp Switch S Link Modem Connection Time
- hpSwitchSLinkModemConnTime 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.4 (defined in hpprocurve-config)
The number of seconds to wait for data mode and clear to send and receiver ready signals after asserting request to send and terminal ready signals. Valid values are 0(switch will wait forever for the modem) through 300(5 minutes). - hp Switch S Link Modem Dis Connection Time
- hpSwitchSLinkModemDisConnTime 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.6 (defined in hpprocurve-config)
The number of seconds to wait after the modem is disconnected before allowing the modem to be reconnected. Valid values are 0(allow a connection as soon as possible, the default) through 60 (1 minute). - hp Switch S Link Modem Connection Time
- hpSwitchSLinkModemConnTime 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.4 (defined in hpprocurve-v2-config)
The number of seconds to wait for data mode and clear to send and receiver ready signals after asserting request to send and terminal ready signals. Valid values are 0(switch will wait forever for the modem) through 300(5 minutes). - hp Switch S Link Modem Dis Connection Time
- hpSwitchSLinkModemDisConnTime 1.3.6.1.4.1.11.2.14.11.5.1.7.1.6.6 (defined in hpprocurve-v2-config)
The number of seconds to wait after the modem is disconnected before allowing the modem to be reconnected. Valid values are 0(allow a connection as soon as possible, the default) through 60 (1 minute).
