The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for poll address
- a3 Com Poll Address
- a3ComPollAddress 1.3.6.1.4.1.43.29.4.22.1.1.2 (defined in A3COM-SWITCHING-SYSTEMS-POLL-MIB)
This DisplayString is the network address of the device to monitor. Typically this is an IP, dotted IP format, IP's hostname, IPX or AppleTalk. The following formats can be used: IP cccc - ipAddress MIB IP nnn.nnn.nnn.nnn - dotted format IP hostname IPX AABBCCDD:AABBCCDDEEFF - network : node AppleTalk n[...].n[...] - dotted notation The object a3ComPollAddressType is used to indicate how this object will be interpreted. This object may not be modified if the associated a3ComPollReport is equal to busy(2). When this object is successfully set, a3ComPollReport will be set to idle(1). - a3 Com Poll Address Type
- a3ComPollAddressType 1.3.6.1.4.1.43.29.4.22.1.1.3 (defined in A3COM-SWITCHING-SYSTEMS-POLL-MIB)
This defines the method used to interpret the a3ComPollAddress, which implies on the protocol to be used. Writing an address to the a3ComPollAddress object causes a default a3ComPollAddressType value to be setup. The default value is derived from the format of the address - four octets means ip(2), four sets of numeric values separated by dot means ipdotted(3), eight and twelve octets separated by colon means ipx(5), and two sets of numeric values separated by a dot means appletalk(6). If the address type cannot be figured out, and this object is not currently set to ipname(4), it will then be set to unknown(1). In other words, this object will remain unchanged if its current value is ipname(4) and a more specific type cannot be given to it. Thus, for the mot part, when setting this object manually, that needs to be done after setting a3ComPollAddress. For ip hostname(4), this field must be set manually. Furthermore, DNS client must be locally enabled to allow for conversion from name to ip address. If the requested protocol is not supported or is not compatible with the a3ComPollAddress, an error is returned when an attempt is made to set a3ComPollAction to activate(2), and a3ComPollReport will be set to noResource(4). This object may not be modified if the associated a3ComPollReport is equal to busy(2). When this object is successfully set, a3ComPollReport will be set to idle(1). - a3 Com Poll Source Address
- a3ComPollSourceAddress 1.3.6.1.4.1.43.29.4.22.1.1.9 (defined in A3COM-SWITCHING-SYSTEMS-POLL-MIB)
This DisplayString is the network address of the local interface to receive ping query. Typically this is an IP, IPX or AppleTalk. The following formats can be used. IP cccc - ipAddress MIB IP nnn.nnn.nnn.nnn - dotted format IPX AABBCCDD:AABBCCDDEEFF - network : node AppleTalk n[...].n[...] - dotted notation If a3ComPollSourceAddress is set to empty, which is the default value, the sending device will pick the best interface to receive the response for its queries. The object a3ComPollAddressType is used to indicate how this object will be interpreted, as well as a3ComPollAddress. An exception exists when a3ComPollAddressType is set to ipname(4): this object will be parsed as if a3ComPollAddressType was set to ip(2) or as ipdotted(3), depending on the length of the object value. Therefore, ip name is not supported for a3ComPollSourceAddress. This object may not be modified if the associated a3ComPollReport is equal to busy(2). When this object is successfully set, a3ComPollReport will be set to idle(1). - Cisco BSC Ext Poll Address
- bscExtPollAddress 1.3.6.1.4.1.9.9.36.1.3.1.1.1 (defined in CISCO-BSC-MIB)
The poll address of the station configured by the bsc extended-address command.
