The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for port admin status
- Frame Relay Interface Port Default Compression Admin Status
- frxPortDefaultCompressionAdminStatus 1.3.6.1.4.1.800.2.8.1.1.1.7 (defined in XYLAN-FRAME-RELAY-MIB)
This object controls whether or not an unconfigured virtual circuit will attempt (enable) or not attempt (disable) to negotiate for compression. - m013 Frx Port Admin Status
- m013FrxPortAdminStatus 1.3.6.1.4.1.800.2.25.3.1.1.4 (defined in XYLAN-M013-MIB)
If set to enabled, enables Frame Relay Interface. If set to disabled, disables Frame Relay Interface - m013 Frx Port Default Ip Routing Admin Status
- m013FrxPortDefaultIpRoutingAdminStatus 1.3.6.1.4.1.800.2.25.3.1.1.5 (defined in XYLAN-M013-MIB)
If set to enabled, enables Default IP Routing. If set to disabled, disables Default IP Routing - m013 Frx Port Default Bridging Admin Status
- m013FrxPortDefaultBridgingAdminStatus 1.3.6.1.4.1.800.2.25.3.1.1.6 (defined in XYLAN-M013-MIB)
If set to enabled, enables Default Bridging. If set to disabled, disables Default Bridging. - port Admin Status
- portAdminStatus 1.3.6.1.4.1.43.1.12.3.1.1.4.1.1.3 (defined in 3comab9300)
Administrative status of the port. An error is returned if this port has been selected as the system reference clock and an attempt is made to change this object to out-of-service. - Character Port Admin Status
- charPortAdminStatus 1.3.6.1.2.1.19.2.1.6 (defined in rfc1316)
The port's desired state, independent of flow control. 'enabled' indicates that the port is allowed to pass characters and form new sessions. 'disabled' indicates that the port is allowed to pass characters but not form new sessions. 'off' indicates that the port is not allowed to pass characters or have any sessions. 'maintenance' indicates a maintenance mode, exclusive of normal operation, such as running a test. - Repeater Port Admin Status
- rptrPortAdminStatus 1.3.6.1.2.1.22.1.3.1.1.3 (defined in rfc1516)
Setting this object to disabled(2) disables the port. A disabled port neither transmits nor receives. Once disabled, a port must be explicitly enabled to restore operation. A port which is disabled when power is lost or when a reset is exerted shall remain disabled when normal operation resumes. The admin status takes precedence over auto- partition and functionally operates between the auto-partition mechanism and the AUI/PMA. Setting this object to enabled(1) enables the port and exerts a BEGIN on the port's auto-partition state machine. (In effect, when a port is disabled, the value of rptrPortAutoPartitionState for that port is frozen until the port is next enabled. When the port becomes enabled, the rptrPortAutoPartitionState becomes notAutoPartitioned(1), regardless of its pre-disabling state.) - Character Port Admin Status
- charPortAdminStatus 1.3.6.1.2.1.19.2.1.6 (defined in rfc1658)
The port's desired state, independent of flow control. 'enabled' indicates that the port is allowed to pass characters and form new sessions. 'disabled' indicates that the port is allowed to pass characters but not form new sessions. 'off' indicates that the port is not allowed to pass characters or have any sessions. 'maintenance' indicates a maintenance mode, exclusive of normal operation, such as running a test. 'enabled' corresponds to ifAdminStatus 'up'. 'disabled' and 'off' correspond to ifAdminStatus 'down'. 'maintenance' corresponds to ifAdminStatus 'test'. - Cabletron Bridge Load Share Port Admin Status
- ctBridgeLoadSharePortAdminStatus 1.3.6.1.4.1.52.4.1.2.3.10.2.1.3 (defined in ctron-bridge-mib)
The administrative state of the port associated with this instance of load share. - Cabletron DLSw Port Admin Status
- ctdlswPortAdminStatus 1.3.6.1.4.1.52.4.1.2.8.2.1.1.4 (defined in ctron-dlsw-mib)
Sets the administrative state of DLSw frame forwarding for this port. - sfps In Port Config Admin Status
- sfpsInPortConfigAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.1.1.2 (defined in ctron-sfps-port-mib)
Sets the administrative state of the SFPS inbound switch port for which the entry exists. - sfps Out Port Config Admin Status
- sfpsOutPortConfigAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.1.2.1.2 (defined in ctron-sfps-port-mib)
Sets the administrative state of the SFPS outbound switch port for which the entry exists. - sfps In Port Statistics Admin Status
- sfpsInPortStatsAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.2.1.1.2 (defined in ctron-sfps-port-mib)
Sets the administrative state of the SFPS packet and byte counters on the inbound SFPS switch port for which this entry exists. - sfps Out Port Statistics Admin Status
- sfpsOutPortStatsAdminStatus 1.3.6.1.4.1.52.4.2.4.2.1.2.2.2.1.2 (defined in ctron-sfps-port-mib)
Sets the administrative state of the SFPS packet and byte counters on the outbound SFPS switch port for which this entry exists. - vlan Port Admin Status
- vlanPortAdminStatus 1.3.6.1.4.1.52.4.2.12.1.2.6.1.1.5 (defined in ctron-sfps-vlan-mib)
- switch Port Admin Status
- switchPortAdminStatus 1.3.6.1.4.1.52.259.10.3.4.1.1.1.3 (defined in elh100-mib)
The administrative status of the port. Setting this object to enabled(1) enables the port. Setting this object to disabled(2) disables the port. On media modules, port 2 (the internal 10Mbps port) cannot be managed. The external port cannot be managed on any module. In these cases, attempts to set this object are rejected with an error-status of badValue(3). The factory setting for manageable ports is enabled(1). Note that if switchModuleActive is notActive(2), then the switch is disabled no matter what its administrative status. - port Physical X25 Admin Row Status
- portPhyX25AdminRowStatus 1.3.6.1.4.1.173.7.3.1.1.1.11 (defined in netlink-specific-mib)
This variable is used to manage the creation and deletion of conceptual rows in the portPhyX25AdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. - port Logical X25 Admin Row Status
- portLogicalX25AdminRowStatus 1.3.6.1.4.1.173.7.3.1.3.1.5 (defined in netlink-specific-mib)
This variable is used to manage the creation and deletion of conceptual rows in the portLogicalX25AdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. - port Bsci Admin Row Status
- portBsciAdminRowStatus 1.3.6.1.4.1.173.7.3.4.1.1.28 (defined in netlink-specific-mib)
This variable is used to manage the creation and deletion of conceptual rows in the portBsciAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. - port Sdlc Admin Row Status
- portSdlcAdminRowStatus 1.3.6.1.4.1.173.7.3.5.1.1.13 (defined in netlink-specific-mib)
This variable is used to manage the creation and deletion of conceptual rows in the portSdlcAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. - port Voice Admin Row Status
- portVoiceAdminRowStatus 1.3.6.1.4.1.173.7.3.8.1.1.35 (defined in netlink-specific-mib)
This variable is used to manage the creation and deletion of conceptual rows in the portVoiceAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. - agent Port Auto Negotiated Admin Status
- agentPortAutoNegAdminStatus 1.3.6.1.4.1.14179.1.2.12.1.13 (defined in AIRESPACE-SWITCHING-MIB)
This object identifies the administration status of auto negotiation for this port.
