The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for port line
- Fddi PORT Line State Table
- a3ComFddiPORTLSTable 1.3.6.1.4.1.43.29.10.4.2 (defined in A3COM-SWITCHING-SYSTEMS-FDDI-MIB)
A list of optional PORT line state entries. - Fddi PORT Line State Entry
- a3ComFddiPORTLSEntry 1.3.6.1.4.1.43.29.10.4.2.1 (defined in A3COM-SWITCHING-SYSTEMS-FDDI-MIB)
Maintenance line state and PC line state information for a given PORT within a given SMT. - Fddi PORT Maint Line State
- a3ComFddiPORTMaintLS 1.3.6.1.4.1.43.29.10.4.2.1.3 (defined in A3COM-SWITCHING-SYSTEMS-FDDI-MIB)
The PORT Maintenance Line State specifies the line state (Maint_LS) to be transmitted when the PCM state machine for the port is in state PC9 Maint. - Fddi PORT PC Line State
- a3ComFddiPORTPCLS 1.3.6.1.4.1.43.29.10.4.2.1.4 (defined in A3COM-SWITCHING-SYSTEMS-FDDI-MIB)
This attribute indicates the line state (PC_LS) received by the port. - Sys Token Ring Port Line Errors
- a3ComSysTokenRingPortLineErrors 1.3.6.1.4.1.43.29.4.13.2.1.8 (defined in A3COM-SWITCHING-SYSTEMS-MIB)
This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame. - a3 Com Sys Token Ring Port Line Errors
- a3ComSysTokenRingPortLineErrors 1.3.6.1.4.1.43.29.4.13.2.1.8 (defined in A3COM-SWITCHING-SYSTEMS-TOKEN-RING-MIB)
This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame. - dsx3 Port Config Line Status
- dsx3PortConfigLineStatus 1.3.6.1.4.1.800.2.11.2.1.1.15 (defined in XYLAN-DS3-MIB)
This object indicates the line status of a ds3/e3 interface. Each bit position (bit-0 to bit-18) represents one failure condition of the interface. Bit-19 and bit-20 are used to represent Timing Marker bit and National Use bit. Note that the SYNTAX type of Counter instead of INTEGER is used here as there are more than 16 different conditions to represent. The followings define the various bit position and their meanings: Bit Description 0: No alarm present 1: Out of Frame Alarm received 2: Loss Of Signal Alarm received 3: Alarm Indication Signal Alarm received 4: Red Alarm received 5: Far End Receive Failure Alarm received (Non E3 G.751 only) Remote Alarm Indication Alarm received (E3 G.751 only) 6: Change Of Frame Alignment Alarm received 7: PLCP Out Of Frame Alarm received 8: PLCP Yellow Alarm received 9: PLCP Framing Bit Error Alarm received 10: PLCP Bit Interleaved Parity Error Alarm received 11: PLCP Loss Of Frames Alarm received 12: PLCP Far End Block Error Alarm received 13: Cell Loss Alarm received 14: Far End Block Error Alarm received 15: Parity Error Alarm received 16: Trail Trace ID Mismatch Alarm received (E3 G.832 only) 17: Rx Payload Type Mismatch Alarm received (E3 G.832 only) 18: Unequipped Payload Type received (E3 G.832 only) 19: Timing Marker Bit (bit 8 of the E3 G.832 Maintenance and Adaptation bye) received. 20: National Use bit (bit 12 of the frame in a E3 G.751 frame) received. - dsx3 Port Statistics Line Code Vio Event
- dsx3PortStatsLineCodeVioEvent 1.3.6.1.4.1.800.2.11.2.2.1.9 (defined in XYLAN-DS3-MIB)
Total number of Line Code Violation events that have been received on this port. This is a count of both Bipolar Violation (BPV) and Excessive zeros (EXZs). - dsx3 Port Interval Line Code Vio Event
- dsx3PortIntervalLineCodeVioEvent 1.3.6.1.4.1.800.2.11.2.3.1.11 (defined in XYLAN-DS3-MIB)
Total number of line code violation events that have been received on this port. This is a count of both Bipolar Violation (BPV) and Excessive zeros (EXZs) since it's cleared by the managing station. - cbr DS1E1 Port Configuration Line Code
- cbrDS1E1PortConfLineCode 1.3.6.1.4.1.43.1.12.3.1.1.15.2.1.1.2 (defined in 3comab9300)
This object indicates the zero code suppression technique configured to the specified T1/E1 port interface. The bipolar with 8 zero substitution (B8ZS) technique is applicable to T1 interfaces ONLY. The High Density Binary Three (HDB3) is applicable to E1 interfaces ONLY. - ima Port Line Code
- imaPortLineCode 1.3.6.1.4.1.43.1.12.3.1.1.19.2.1.1.2 (defined in 3comab9300)
This object indicates the line coding configured for the port. - ds3 Port Line Rate
- ds3PortLineRate 1.3.6.1.4.1.43.1.12.3.1.1.11.1.1.1.11 (defined in C-PRODUCT-DS3-MIB)
Physical Line data transfer rate of the DS3 port. Unit: CPS. - e3 Port Line Rate
- e3PortLineRate 1.3.6.1.4.1.43.1.12.3.1.1.13.1.1.1.8 (defined in C-PRODUCT-E3-MIB)
Physical Line data transfer rate of the E3 port. Unit: CPS. - port T1 Admin Line Build Out
- portT1AdminLineBuildOut 1.3.6.1.4.1.173.7.3.7.1.1.6 (defined in netlink-specific-mib)
::= { portT1AdminEntry 6 } SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION " - port T1 Operation Line Build Out
- portT1OperLineBuildOut 1.3.6.1.4.1.173.7.3.7.2.1.6 (defined in netlink-specific-mib)
::= { portT1OperEntry 6 } SYNTAX INTEGER { sync(1), bisync(2) } ACCESS read-only STATUS mandatory DESCRIPTION "
