The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for "port status"
- Filter Port Status
- a3ComFilterPortStatus 1.3.6.1.4.1.43.29.4.20.2.4.1.4 (defined in A3COM-SWITCHING-SYSTEMS-FILTER-MIB)
The status column for this port group entry. This OBJECT can be set to: createAndGo(4) destroy(6) The following values may be read: active(1) Setting this object to createAndGo(4) will result in the agent attempting to create and commit the row based on the contents of the objects in the row. If all the necessary information is presented in the row and the values are acceptible to the agent, the agent will change the status to active(1). If there are any necessary objects are not set, the agent will reject the creation request. When the state of the row translates to active(1), the agent will add the corresponding port to the indicated port group. Setting this object to destroy(6) will remove this port from corresponding port group. - els100 Port Status
- els100PortStatus 1.3.6.1.4.1.52.1011.2.1.2 (defined in ctels100-ng-mib)
The connection (link) status of the port, either up (linked) or down (not linked). - bdg Port Status
- bdgPortStatus 1.3.6.1.4.1.173.7.9.1.2.4 (defined in ctron-bdg-mib)
The status in which the port is operating. The status messages for Ports 1 and 2 are: OFF - The port is off, due to a failed network interface chip associated with that port. OK/SQE ON - The port is communicating with the network and the transceiver making the connection to the network has SQE enabled. OK/SQE OFF - The port is communicating with the network and the transceiver making the connection to the network has SQE disabled. CARRIER LOST - Communication with the network has not been established or has been lost. - Cabletron CDP Port Status
- ctCDPPortStatus 1.3.6.1.4.1.52.4.1.2.19.2.3.1.2 (defined in ctron-cdp-mib)
The current state administrative of cdp on a physical port. The ability to enable and disable the sending of CDP pdu's on a per port basis is controlled here. - Cabletron Priority Ext Port Status
- ctPriorityExtPortStatus 1.3.6.1.4.1.52.4.1.2.14.4.1 (defined in ctron-priority-extensions-mib)
Defines the status of the priority packet forwarding based on receive port. Setting ctIfPriorityExtPortStatus to a value of disable(2), disables the forwarding of packets based on priority table information. All information remains in existence but is not considered in the forwarding decision. - vlan Port Port Status
- vlanPortPortStatus 1.3.6.1.4.1.52.4.2.12.1.2.6.1.1.2 (defined in ctron-sfps-vlan-mib)
- Net Link If Port Status
- nlIfPortStatus 1.3.6.1.4.1.173.7.4.1.1.8 (defined in netlink-specific-mib)
The status of this port state. Valid for ports 1-64 only. - lacp Port Status
- lacpPortStatus 1.3.6.1.4.1.52.4.12.30.1.4.1.1.2 (defined in v2h124-24-mib)
Whether 802.3ad LACP is enabled. - prio Ip Port Status
- prioIpPortStatus 1.3.6.1.4.1.52.4.12.30.1.13.7.1.4 (defined in v2h124-24-mib)
Writing this to invalid(2) destroys an entry. - port Sec Port Status
- portSecPortStatus 1.3.6.1.4.1.52.4.12.30.1.17.2.1.1.2 (defined in v2h124-24-mib)
disable port security. - enterasys Dot1x Authentication Authentication Controlled Port Status
- etsysDot1xAuthAuthControlledPortStatus 1.3.6.1.4.1.5624.1.2.18.1.2.1.2.1.5 (defined in enterasys-8021x-extensions-mib)
The current value of the controlled Port status parameter for the virtual port. - Enterasys Port Web Authentication Port Status Group
- etsysPwaPortStatusGroup 1.3.6.1.4.1.5624.1.2.8.5.3 (defined in enterasys-pwa-mib)
The status of all login information on a per ifIndex basis can be obtained here. - Cisco 6400NSP Sonet APS Work Port Status
- c64SonetAPSWorkPortStatus 1.3.6.1.4.1.9.10.27.1.1.8.1.9 (defined in CISCO-6400-CHASSIS-MIB)
in working port. - Cisco 6400NSP Sonet APS Protect Port Status
- c64SonetAPSProtectPortStatus 1.3.6.1.4.1.9.10.27.1.1.8.1.18 (defined in CISCO-6400-CHASSIS-MIB)
in protection port. - Cisco 2900 Port Status
- c2900PortStatus 1.3.6.1.4.1.9.9.87.1.4.1.1.22 (defined in CISCO-C2900-MIB)
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the switch has detected a port that is malfunctioning it will place that port into the broken(10) state. For ports which are disabled(see dot1dStpPortEnable), this object will have a value of disabled(2). Since the switch implements three additional states which are not part of IEEE Standard, these additional states are possible values for c2900PortStaus. The additional states are preforwarding(6), secureforwarding(8), and suspended(9). Note: except for these additional states, this object is the same as the dot1dStpPortState object. Default value: blocking(2). This object is only supported for static VLAN access ports. - Cisco Distributed Director Server Port Status
- cddServerPortStatus 1.3.6.1.4.1.9.9.197.1.3.2.1.9 (defined in CISCO-DIST-DIRECTOR-MIB)
Indicates whether the port service is available or not. The possible service statuses are as follows: undetermined - the service was not tested or the service state can't be determined. up - the service is known to be available. down - the service is known to be unavailable.
