AGENT-GENERAL-MIB Download

agentMgmtProtocolCapability

The network management protocol(s) supported by this agent.

agentMibCapabilityTable

A list of MIB capability entries supported by this agent.

agentMibCapabilityEntry

A MIB capability entry containing objects that describe a particular MIB supported by this agent.

agentMibCapabilityIndex

A list of Agent MIB Capability Description entries.

agentMibCapabilityDescr

The name of the MIB supported by the agent.

agentMibCapabilityVersion

The version of the MIB specified in this entry.

agentMibCapabilityType

The type of MIB specified in this entry.

agentStatusConsoleInUse

This indicates whether the console is currently in use.

agentStatusSaveCfg

This indicates the status of the device configuration. other (1) - This entry is currently in use but the conditions under which it will remain so are determined by each of the following values. proceeding (2) - The device configuration is currently being ...

agentStatusFileTransfer

The status of the firmware download control. If the value is stated as 'other', the firmware has not been updated since the device was started.

agentCPUutilizationIn5sec

The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy).

agentCPUutilizationIn1min

The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy).

agentCPUutilizationIn5min

The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy).

agentDualImageStatus

The dual image status.

agentPORTutilizationTable

This table specifies the current utilization of a specified port.

agentPORTutilizationEntry

A list of information regarding the port utilization function.

agentPORTutilizationProtIndex

This object indicates the module's port number.

agentPORTutilizationTX

The current rate of transmitted frames on the specified port.

agentPORTutilizationRX

The current rate of received frames on the specified port.

agentPORTutilizationUtil

The current percentages regarding port statistics.

agentDRAMutilizationTable

Information about DRAM memory.

agentDRAMutilizationEntry

A list of information about DRAM memory.

agentDRAMutilizationUnitID

Specifies the unit ID. If the ID equals zero, it means the current device.

agentDRAMutilizationTotalDRAM

The size of total DRAM memory.

agentDRAMutilizationUsedDRAM

The size of used DRAM memory.

agentDRAMutilization

The percentage of used DRAM memory of the total DRAM memory available. The value will be between 0% (idle) and 100% (very busy).

agentFLASHutilizationTable

Information about FLASH memory.

agentFLASHutilizationEntry

Information about FLASH memory.

agentFLASHutilizationUnitID

Specifies the unit ID. If the ID equals zero, it means the current device.

agentFLASHutilizationTotalFLASH

The total size of FLASH memory.

agentFLASHutilizationUsedFLASH

The size of the used FLASH memory.

agentFLASHutilization

The percentage of used FLASH memory in total FLASH memory. The value will be between 0% (idle) and 100% (very busy).

agentStatusReset

This indicates the status of 'agentReset'.

agentSerialNumber

A text string containing the serial number of this device.

agentBscSwFileTable

A list of MIB Basic Config entry support files updated by this agent.

agentBscSwFileEntry

A basic configuration entry containing objects that describe a particular MIB supported by this agent.

agentBscSwFileIndex

The table index for the file entry

agentBscSwFileDscr

The description of the software file purpose in this entry. Note: For systems that do not support change of this object, setting a value for this object will cause the system to return bad-value error messages.

agentBscSwFileAddr

The IP address where the file that needs to be downloaded is located, or the IP address where the file will be uploaded to.

agentBscSwFileTransferType

The channel through which the file will be downloaded or uploaded. Note: For systems which do not support all channels, setting a value to the unsupported channel will cause the system to return bad-value error messages.

agentBscSwFile

The name of the file to be downloaded from, or uploaded to, the TFTP server.

agentBscSwFileLocateId

This object describes the type of file. runtime-code (1), log-file (2), cfg-file (3) Note: For systems which do not support change of this object, setting a value for this object will cause the system to return bad-value error messages.

agentBscSwFileLoadType

This object provides the user with a choice of uploading or downloading the selected file. Note: For systems which do not support a change of this object, setting a value to this object will cause the system to return bad-value error messages.

agentBscSwFileCtrl

This object gives the user the option of downloading runtime software. This setting will take effect when the system restarts. See Note (1) below Note: For systems which do not support change for this object, setting a value to this object will cause the ...

agentBscSwFileBIncrement

This object indicates whether the previous configuration will remain valid or not after downloading the configuration file. True: keep valid False: erase.

agentBscSwFileCtrlID

The section ID of the firmware image or configuration file. A value of 0 indicates the boot-up firmware image or configuration file.

agentBscSwFileCtrlUnitID

Specifies which unit of the switch stack the firmware image will be downloaded from. One or more units can be set to this list. Each bit from left to right represents the switch from unit ID 1 to unit ID 12. A null entry in this field denotes all switche ...

agentBscSwFileIPv6Addr

The IPv6 address where the file is to be downloaded from or uploaded to.

agentBscSwFileBootUpImage

The result of the download will depend on whether the boot_up option is specified. Case 1: In the case where the master unit provides the file system and the slave unit does not provide the file system, when boot_up is specified, the file will be download ...

agentBscSwFileForceAgree

When the force_agree option is specified, the reboot command will be executed immediately without further confirmation by the user. True: force_agree option is specified. False: force_agree option is not specified.

agentBscSwFileInterfaceName

This node is used to specify the interface name when the agentBscSwFileIPv6Addr is the link local address.

agentFileTransfer

This object will execute the download or upload action. If start (2) is chosen, it will begin to download/upload, with no reset to follow. If start-and-reset (3) is chosen, then the reset will be activated after completing the download or upload. No actio ...

agentSystemReset

This object indicates the agent system reset state. Setting this object to no-reset (4) has no effect. Setting this object to cold-start (2) or warm-start (3) will reset the agent. The agent always returns to no-reset (4) when this object is read. This ob ...

agentRs232PortConfig

This object indicates the RS-232C mode once the device has restarted.

agentOutOfBandBaudRateConfig

This object allows the user to specify an out-of-band baud rate, which will take effect upon system restart. Note: Because these functions will be limited by the support for the system in question, some of the selected items will be invalid. When the user ...

swMultiImageInfoTable

swMultiImageInfoEntry

A list of information about multiple image management.

swMultiImageInfoID

The stacking section ID of the firmware image. The stacking section ID = 256 * Unit ID + Image File ID.

swMultiImageVersion

The recorded downloaded firmware version.

swMultiImageSize

The recorded downloaded firmware size.

swMultiImageUpdateTime

The recorded firmware updated time.

swMultiImageFrom

The recorded IP address of the TFTP server

swMultiImageSendUser

The record of the user who downloaded the firmware.

swMultiImageFileName

When the system is set to boot from SD card, this object will display the recorded path name of the boot firmware file.

swMultiCfgInfoTable

swMultiCfgInfoEntry

A list of information about multiple configuration files.

swMultiCfgInfoID

The section ID of the configuration files.

swMultiCfgVersion

The recorded downloaded configuration version.

swMultiCfgSize

The recorded downloaded configuration size (in bytes). ::= { swMultiCfgInfoEntry 3 } SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION The recorded configuration update time displayed in string format, i.e. yyyy/mon/d ...

swMultiCfgFrom

The recorded IP address of the TFTP server.

swMultiCfgSendUser

The record of the user who downloaded the configuration file

swMultiCfgFileName

When the system is set to boot from SD card, this object displays the recorded path name of the boot configuration file.

swMultiCfgCurrentUsed

The indicated configuration file ID of the system currently in use.

swMultiCfgBootUp

This object indicates the configuration file ID which will take effect upon the next reboot.

swMultiCfgCtrlTable

swMultiCfgCtrlEntry

A list of information about multiple configuration management.

swMultiCfgCtrlID

The section ID of the configuration file.

swMultiCfgAction

save: Save configuration to active configuration ID when the parameter is omitted. active: Set any valid configuration to be the active configuration. delete: Removes the configuration from the flash memory. This configuration cannot be the active or curr ...

systemSeverityTrapControl

Indicates the level of trap severity control. The system has a severity level control and each trap should have a severity control set. When trap events occur and its severity are higher than the system severity control level, the trap works as defined. I ...

systemSeverityLogControl

Indicates the level of trap severity control. The system has a severity level control and each trap should have a severity control set. When trap events occur and its severity is higher than the system severity control level, the trap works as defined. If ...

agentTrustedHostTable

This table contains trusted host information.

agentTrustedHostEntry

A list of information about trusted hosts.

agentTrustedHostIndex

The index of the trusted host entry.

agentTrustedHostIPAddress

Specifies the IP address of the trusted host.

agentTrustedHostRowStatus

Indicates the status of this entry. When creating a trusted host entry, the IP address should also be set.

agentTrustedHostIPSubnetMask

Specifies the IP subnet mask of the trusted host.

agentTrustedHostForSNMP

Specifies the trusted host for SNMP.

agentTrustedHostForTELNET

Specifies the trusted host for Telnet.

agentTrustedHostForSSH

Specifies the trusted host for SSH.

agentTrustedHostForHTTP

Specifies the trusted host for HTTP.

agentTrustedHostForHTTPS

Specifies the trusted host for HTTPS.

agentTrustedHostForPING

Specifies the trusted host for PING.

agentTrustedHostAddrType

The type of trusted host address as specified by object 'agentTrustedHostAddr'.

agentTrustedHostAddr

Specifies the IP address of the trusted host.

agentTrustedHostIPv6PrefixLen

Specifies the IPv6 prefix length of the IPv6 trusted host.

agentTrustedHostDelAllState

Used to delete all trusted host entries.

agentFDBClearAllState

Used to clear all FDB entries.

agentARPClearAllState

Used to clear all ARP entries.

agentGratuitousARPSendIpifStatusUpState

This is used to enable/disable sending of gratuitous ARP request packets while IPIF interface come up. This is used to automatically announce the interface's IP address to other nodes. By default, the state is enabled, and only one ARP packet will be broa ...

agentGratuitousARPSendDupIpDetectedState

This is used to enable/disable sending of gratuitous ARP request packets while a duplicate IP is detected. By default, the state is enabled. The duplicate IP detected means that the system received an ARP request packet that was sent by an IP address that ...

agentGratuitousARPLearningState

This is used to enable/disable learning of an ARP entry in the ARP cache based on the received gratuitous ARP packet. If the switch receives a gratuitous ARP request/reply packet and the sender's IP address is in its ARP table, it should update the ARP en ...

agentGratuitousARPTable

Gratuitous ARP Table Information.

agentGratuitousARPEntry

A list of information from the Gratuitous ARP Table.

agentGratuitousARPInterfaceName

The name of the IP interface.

agentGratuitousARPPeriodicalSendInterval

This is used to configure the interval for the periodic sending of gratuitous ARP request packets. 0 means do not send gratuitous ARP periodically.

agentGratuitousARPTrapState

It indicates the state of the gratuitous ARP trap. The switch can trap the IP conflict event to inform the administrator. By default, the trap is disabled.

agentGratuitousARPLogState

This indicates the state of the gratuitous Log trap. The switch can log the IP conflict event to inform the administrator. By default, the event log is enabled.

swMultiImageCtrlTable

swMultiImageCtrlEntry

A list of information about multiple image management.

swMultiImageCtrlID

The stacking section ID of the firmware image. The stacking section ID = 256 * Unit ID + Image File ID.

swMultiImageCtrlAction

This object indicates the running status of the image which is specified by the swMultiImageCtrlID and swMultiImageCtrlUnitID. config-as-bootup-fw (1) - configured as bootup firmware by indicated firmware(ID). delete (2) - delete the firmware by indicated ...

agentOutOfBandParityBits

This object indicates the out-of-band parity bits.

agentOutOfBandStopBits

This object indicates the out-of-band stop bits.

agentOutOfBandAutoLogoutConfig

This object allows the user to specify an out-of-band auto logout time.

agentBscFileSystemTable

A list of MIB File System Basic Configuration entries supported by the file update of this agent.

agentBscFileSystemEntry

A File System basic configuration entry that contains objects describing a particular MIB supported by this agent.

agentBscFileSystemIndex

The table index for the file entry. This object describes the file type. runtime-code (1), log-file (2), cfg-file (3), attack-log-file (7)

agentBscFileSystemDscr

The description of the software file purpose in this entry.

agentBscFileSystemServerAddr

The IP address where the file to be downloaded is located, or the IP address where the file will be uploaded to.

agentBscFileSystemServerIPv6Addr

The IPv6 address where the file is to be downloaded from or uploaded to.

agentBscFileSystemServerFileName

The name of the file to be downloaded from or uploaded to the TFTP server If agentBscFileSystemDeviceFileName is not set, the switch will default to the bootup file as the runtime image for the switch.

agentBscFileSystemDeviceDriverID

Specifies the drive of the device where the firmware to be uploaded/downloaded is located. If none (1) is specified, the switch will default to the current drive.

agentBscFileSystemDeviceFileName

The name of the file to be downloaded to the device, or to be uploaded from the device. When downloading or uploading, the agentBscFileSystemServerFileName must also be set.

agentBscFileSystemLoadType

This object allows the user to select a download or upload function for the file. Note: For systems which do not support change of this object, setting a value for this object will cause the system to return a bad-value error message. ::= { agentBscFileSy ...

agentBscFileSystemBootUpImage

The result of the download will depend on whether the boot_up option has been specified. Case 1: In the case of the master unit providing the file system and the slave unit not providing the file system, when the boot_up parameter is specified, then the f ...

agentBscFileSystemForceAgree

When the force_agree option is specified, the reboot command will be executed immediately without further confirmation by the user. True: force_agree option is specified. False: force_agree option is not specified..

agentBscFileSystemCtrl

This object allows the user to download runtime software. The settings will take effect when the system restarts. See Note (1) below Note: For systems which do not support value changes to this object, setting these values will cause the system to return ...

agentBscFileSystemSaveConfigDriverID

The drive on the device where the configuration file is to be saved. If none (1) is specified, the switch places the file on the current drive by default.

agentBscFileSystemSaveConfigFileName

The name of the configuration file to be saved to the device. When agentBscFileSystemSaveCfg is set to cfg (2), and if the agentBscFileSystemSaveConfigFileName is not null, the configuration file will be saved to the set file name. If null, the configura ...

agentBscFileSystemSaveCfg

This indicates the method of saving information to the NV-RAM of the device. other (1) - none of the following. cfg (2) - save configuration. log (3) - save log. all (4) - save both ( active configuration and log).

agentFileSystemConfigTable

This table indicates information about bootup files.

agentFileSystemConfigEntry

A list of information about bootup files for each unit of the switch stack.

agentFileSystemUnit

The unit ID.

agentFileSystemDriverID

The drive on the device where the configuration file is to be saved. If none (1) is specified, the switch defaults placement of the file to the current drive.

agentFileSystemBootImage

When displayed, it shows the current bootup image file name. When set, the set name will be set as the bootup image.

agentFileSystemBootConfig

When displayed, it shows the current bootup configuration file name. When set, the set name will be set as the bootup configuration.

agentFileSystemActConfig

When displayed, it shows null. When set, the set name will be active at once. But the set name will not be set as the bootup configuration.

agentReboot

Used to restart the switch.

agentReset

Used to reset all switch parameters. none (1): No action. This is the default value of this object. config (2): All parameters are reset to default settings. The device will neither save nor reboot. system (3): All parameters are reset to default settings ...

agentFTPFileEntry

A basic configuration entry containing objects describing a particular MIB supported by this agent.

agentFTPFileIndex

The table index for the file entry. This object describes the file type runtime-code (1), log-file (2), cfg-file (3)

agentFTPFileDscr

The description of the software file purpose in this entry. Note: For systems which do not support changes to this object, setting a value for this object will cause the system to return bad-value error messages.

agentFTPFileLoadType

This object provides the user with a choice of uploading or downloading the selected file. Note: For systems which do not support a change of this object, setting a value to this object will cause the system to return bad-value error messages.

agentFTPFileAddr

The IP address where the file to be downloaded is located, or the IP address where the file will be uploaded to.

agentFTPTCPPort

The TCP port number being used to establish the command connection.

agentFTPFileName

The name of the file to be downloaded from, or uploaded to, the FTP server.

agentFTPUserName

This is the user name to enter in upload/download.

agentFTPPassword

This is the password to enter in upload/download.

agentFTPFileCtrlID

The section ID of the firmware image or configuration file. A value of 0 indicates the boot-up firmware image or configuration file.

agentFTPFileBIncrement

This object indicates whether the previous configuration will remain valid or not after downloading the configuration file. True: keep valid False: erase.

agentFTPFileCtrl

This object gives the user the option to download runtime software. The setting will take effect when the system restarts. See Note (1) below Note: For systems which do not support changes to this object, setting a value for this object will cause the sys ...

agentFTPFileBootUpImage

This object indicates whether set the special file as boot up file or not. True: boot-up option is specified. False: boot-up option is not specified.

agentFTPFileForceAgree

When the force-agree option is specified, the reboot command will be executed immediately without further confirmation by the user. True: force-agree option is specified. False: force-agree option is not specified.

agentFTPFileIPv6Addr

The IPv6 address where the file is to be downloaded from or uploaded to.

agentFTPFileInterfaceName

This node is used to specify the interface name when the agentFTPFileIPv6Addr is the local link address.

agentFTPFileUnitID

Specifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bit from left to right represents the switch from unit ID 1 to unit ID 12.If this list is set to n ...

agentSnmpTrapState

This object indicates if the SNMP trap is enabled or disabled.

agentOutOfBandMgmtState

Enables or disables the interface.

agentOutOfBandMgmtIpAddr

The IP address for out of band management. This object can only take the value of the unicast IP address.

agentOutOfBandMgmtSubnetMask

The IP net mask for out of band management.

agentOutOfBandMgmtGateway

The gateway for out of band management.

agentOutOfBandMgmtLinkStatus

The current Link status for out of band management.

agentTrapColdStart

When enabled (1), whenever the device detects a cold start event, a trap will be sent out.

agentTrapWarmStart

When enabled (1), whenever the device detects a warm start event, a trap will be sent out.

agentTrapRmonRisingAlarm

When enabled (1), whenever the device detects a rising alarm event of RMON, a trap will be sent out.

agentTrapRmonFallingAlarm

When enabled (1), whenever the device detects a falling alarm event of RMON, a trap will be sent out.

agentTrapCfgSave

When enabled (1), whenever the device detects a configuration saving completed event, a trap will be sent out.

agentTrapCfgUpload

When enabled (1), whenever the device detects a configuration uploading completed event, a trap will be sent out.

agentTrapCfgDownload

When enabled (1), whenever the device detects a configuration downloading completed event, a trap will be sent out

agentFTPFileSystemTable

FTP management table for file system

agentFTPFileSystemEntry

A File System basic configuration entry that contains objects describing a particular MIB supported by this agent.

agentFTPFileSystemIndex

The table index for the file entry.

agentFTPFileSystemDscr

The description of the software file purpose in this entry.

agentFTPFileSystemLoadType

This object allows the user to select a download or upload function for the file.

agentFTPFileSystemAddressType

The address type of agentFTPFileSystemAddress.

agentFTPFileSystemAddress

This object indicates the FTP server address.

agentFTPFileSystemTCPPort

The TCP port number being used to establish the control connection.

agentFTPFileSystemServerFileName

The name of the file to be downloaded from or uploaded to the FTP server.

agentFTPFileSystemDeviceFileName

The name of the file to be downloaded to the device, or to be uploaded from the device. If agentFTPFileSystemDeviceFileName is not set, the switch will default to the bootup file.

agentFTPFileSystemUserName

This object indicates the user name to access the FTP server.

agentFTPFileSystemPassword

This object indicates the password to access the FTP server.

agentFTPFileSystemCtrlUnitID

Specifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bit from left to right represents the switch from unit ID 1 to unit ID 12.If this list is set to n ...

agentFTPFileSystemBootUpImage

This object indicates whether set the special file as boot up file or not. True: boot-up option is specified. False: boot-up option is not specified.

agentFTPFileSystemCtrl

This object allows the user to execute FTP download/upload.

agentBscCMDLogState

This object indicates the command logging state.

agentIpNumOfIf

The total number of IP interfaces supported by this agent.

agentIpTftpServerAddr

The IP address of the TFTP Server.

agentIpGetIpFrom

This object indicates if the agent gets its system IP address from Bootp/DHCP server at start up.

agentIpAutoconfig

Indicates the status of automatically getting configuration information from a TFTP server connected to a device.

agentIpAutoconfigTimeout

This timer is used to limit the length of time in getting configuration information from a TFTP server connected to a device.

agentTrapManagerEntry

Each entry contains the particular trap manager settings.

agentTrapManagerIndex

A value that uniquely identifies this trapDestEntry.

agentTrapManagerIpAddr

The destination IP address for SNMP traps.

agentTrapManagerComm

The community string used to encode SNMP trap packets being sent to the trap manager.

agentTrapManagerMsgVer

This object indicates the version of trap packets that will be sent to this trap manager. The default setting is SNMP Agent Version Dependent. Note: Because some of these functions will be limited by the support of the system in question, some selected it ...

unitID

The unit ID of the device which triggered the event.

trapInfosystemRestart

This object indicates the last time the device rebooted. ::= { notificationBindings 2 } SYNTAX IpAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION A duplicate IP address with the switch already exists.

agentGratuitousARPMacAddr

This object is the MAC address of the device which has the duplicate IP address.

agentGratuitousARPPortNumber

This indicates the portNum with a string. For example, if the device is in standalone mode, and the port number is 23, the string should be 23. If the device is in stacking mode, and the unit ID is 2, and the port number is 3, the string should be 2:3. :: ...

agentLoginAAAMethod

This method is the AAA login method.

agentLoginUserName

This object is the name of the user login which failed.

agentLoginIpAddr

This object is the login type from the IP address.

agentLoginMacAddr

This object is the login type from a MAC address.

agentLoginAAAServerAddr

This object is the login type through a console authenticated by a AAA server.

agentLoginFailInfo

This object indicates the reason of the login failure.

agentAccessFlashOper

This object indicates the operation of the access flash failure.

agentAccessFlashAddr

This object indicates the address of the access flash failure.

agentCfgOperate

This object indicates the operation type of the configuration.