CISCO-MODEM-MGMT-MIB Download

cmSystemInstalledModem

The actual number of modems that are currently installed within this system.

cmSystemConfiguredGroup

The actual number of modem groups that are currently configured within this system. Maximum value for this object is cmSystemInstalledModem.

cmSystemWatchdogTime

A passive software watchdog timer value will be used to recover a modem which enters into an unexpected state and hangs. When this watch dog timer times out, the modem associated Call Processing state will be set back to IDLE, all related TDM paths will b ...

cmSystemStatusPollTime

The ideal time interval between modem status polling via the out of band management port.

cmSystemMaxRetries

A reply event is expected to be received for every message sent to the modem through the out of band management port. If an expected reply event is not received, the message will be sent to the modem again. This object specifies the maximum number of retr ...

cmSystemModemsInUse

The number of modems in the system that are in the following states: connected, offHook, loopback, or downloadFirmware.

cmSystemModemsAvailable

The number of modems in the system that are onHook. That is, they are ready to accept a call.

cmSystemModemsUnavailable

The number of modems in the system that cannot accept calls. They are in a state other than onHook.

cmSystemModemsOffline

The number of modems in the system, which have been held administratively offline

cmSystemModemsDead

The number of modems in the system with the state bad or downloadFirmwareFailed.

cmGroupTable

Table of descriptive and status information about the groups of modems.

cmGroupEntry

An entry in the table, containing information about a single group of modems.

cmGroupIndex

This object identifies the group containing the modems for which this entry contains information.

cmGroupTotalDevices

The total number of modem devices which are configured in the group.

cmGroupMemberTable

Table of information about the modem members in modem groups.

cmGroupMemberEntry

An entry in the table, containing information about modem members in a group. The modem groups are currently created when an associated Async interface groups are configured via CLI command 'interface group-async' and not via SNMP.

cmSlotIndex

The modem feature card slot number in the group.

cmPortIndex

The modem port number of a modem feature card in the group.

cmLineStatusTable

A collection of objects that describe the status of the modem.

cmLineStatusEntry

An entry in the table, containing status information about a single modem.

cmInterface

The interface that this modem is connected.

cmGroup

The modem group number that the modem may be in.

cmManufacturerID

A textual description to identify the modem, including the manufacturer's name and type of modem.

cmProductDetails

A textual description of the modem, including hardware revision number, firmware revision number, feature set and optionally, its serial number.

cmManageable

The Manageable modem allows to be accessed through the out of band management port in which the modem statistic data can be retrieved, and the Direct Connect session can be used to provide the test and debugging ability. This object specifies whether this ...

cmState

Indicates the current state of modem. The meaning of each state code is explained below: unknown: the current state of the modem is unknown. onHook: the condition similar to hanging up a telephone receiver. The call cannot enter a connected state when t ...

cmCallDirection

The modem can be used either as an incoming call or outgoing call. This object specifies the direction of the current or previous call.

cmDisconnectReason

Indicates the reason that the last connection or call attempt disconnected. The meaning of each reason code is explained below: unknown: the failure reason is unknown or there has been no previous call. lostCarrier: the call was disconnected because the ...

cmCallDuration

This object specifies the call duration of the current or previous call.

cmCallPhoneNumber

The dialed outgoing telephone number of the current or previous call.

cmCallerID

The incoming caller identification of the current or previous call if this entry is not in the connected state.

cmModulationSchemeUsed

The modem modulation scheme used in the current or previous call. This object is valid only for modems which have cmManageable to be true.

cmProtocolUsed

The modem protocol used in the current or previous call. This object is valid only for modems which have cmManageable to be true.

cmTXRate

The speed of modem transmit rate of the current or previous call in bits per second. This object is valid only for modems which have cmManageable to be true.

cmRXRate

The speed of modem receive rate of the current or previous call in bits per second. This object is valid only for modems which have cmManageable to be true.

cmTXAnalogSignalLevel

The modem transmit analog signal level in the current or previous call. The unit used is in dBm. This object is valid for modems that have cmManageable set to true(1) otherwise 0 will be returned.

cmRXAnalogSignalLevel

The modem transmit analog signal level in the current or previous call. The unit used is in dBm. This object is valid for modems that have cmManageable set to true(1) otherwise 0 will be returned.

cmLineConfigTable

A collection of objects that describe some of the configuration info of the modem.

cmLineConfigEntry

An entry in the table, containing configuration information about a single modem.

cmATModePermit

Direct Connect session is used for test and debugging purpose by using the modem AT commands through the out of band management port when cmManageable is true. This object specifies whether the Direct Connect session is permitted to be used at this modem. ...

cmStatusPolling

Modem status and events can be polled through the out of band management port when the cmManageable is true. This object specifies whether this status polling feature is enabled at this modem. If cmManageable is true(1), status polling will occur for the ...

cmBusyOutRequest

This object is used to put modem out of service, i.e. modem cannot make calls or answer calls. If the modem to be busyout is handling a call, the busyout action will be taken after the current call is disconnected. After modem is busyout, the following co ...

cmShutdown

This object is used to put modem out of service, i.e. modem cannot make calls or answer calls. This is a hard busyout command to bring the modem out of service immediately without waiting for the call to be ended normally. After modem is shutdown, the fo ...

cmHoldReset

A command hold-reset will put the state of modem into reset mode until an inverse command to bring modem out of RESET mode. During the period of reset mode, this modem can not be used and is non-functional. This object is only valid when cmState is onHook ...

cmBad

This object can hold modem out of service and marks the modem as suspected or proven to be bad. During the router start-up initialization sequence, modem back-to-back tests will test modems and mark those modems failing tests as bad modems. The managemen ...

cmLineStatisticsTable

A collection of objects that describe the status of the modem.

cmLineStatisticsEntry

An entry in the table, containing status information about a single modem.

cmRingNoAnswers

A counter to count the calls that ringing was detected but the call was not answered at this modem.

cmIncomingConnectionFailures

A counter that indicates the number of incoming connection requests that this modem answered in which it could not train with the other DCE. This object is valid only for modems which have cmManageable to be true.

cmIncomingConnectionCompletions

A counter that indicates the number of incoming connection requests that this modem answered and successfully trained with the other DCE. This object is valid only for modems which have cmManageable to be true.

cmOutgoingConnectionFailures

A counter that indicates the number of outgoing calls from this modem which successfully went off hook and dialed, in which it could not train with the other DCE. This object is valid only for modems which have cmManageable to be true.

cmOutgoingConnectionCompletions

A counter that indicates the number of outgoing calls from this modem which resulted in successfully training with the other DCE.This object is valid only for modems which have cmManageable to be true.

cmFailedDialAttempts

A counter that indicates the number of call attempts that failed because the modem didn't go off hook, or there was no dial tone.

cmNoDialTones

A counter that indicates the number of times the dial tone expected but not received. This object is valid only for modems which have cmManageable to be true.

cmDialTimeouts

A counter that indicates the number of times the dial time-out occurred. This object is valid only for modems which have cmManageable to be true.

cmWatchdogTimeouts

The number of times the Call Processing watchdog timer has expired.

cm2400OrLessConnections

The number of connections initially established at a modulation speed of 2400 bits per second or less. This object is valid only for modems which have cmManageable to be true.

cm2400To14400Connections

The number of connections initially established at a modulation speed of greater than 2400 bits per second and less than 14400 bits per second. This object is valid only for modems which have cmManageable to be true.

cmGreaterThan14400Connections

The number of connections initially established at a modulation speed of greater than 14400 bits per second. This object is valid only for modems which have cmManageable to be true.

cmNoCarriers

A counter that indicates the number of times that the disconnect reason is no carrier. This object is valid only for modems which have cmManageable to be true.

cmLinkFailures

A counter that indicates the number of times that the disconnect reason is link failure. This object is valid only for modems which have cmManageable to be true.

cmProtocolErrors

A counter that indicates the number of times that the out of band protocol error occurred. This object is valid only for modems which have cmManageable to be true.

cmPollingTimeouts

A counter that indicates the number of times that the out of band protocol time-out error occurred. This object is valid only for modems which have cmManageable to be true.

cmTotalCallDuration

A counter that indicates total call duration on the modem. This includes the duration of all previous calls.

cmLineSpeedStatisticsTable

A collection of objects that describe the intial modem line speeds and connections

cmLineSpeedStatisticsEntry

An entry in the table, containing initial speed and connection information about a single modem.

cmInitialLineSpeed

A discrete initial speed at which the given line may operate

cmInitialLineConnections

The number of connections initially established at a given modulation speed. An instance of this object will be only present for those speeds where one or more connections have occurred

cmInitialTxLineConnections

The number of Transmit connections initially established at a given modulation speed. An instance of this object will be only present for those speeds where one or more connections have occurred

cmInitialRxLineConnections

The number of Receive connections initially established at a given modulation speed. An instance of this object will be only present for those speeds where one or more connections have occurred

cmStateNotifyEnable

This variable controls generation of the cmStateNotification. When this variable is 'true(1)', generation of cmStateNotification is enabled. When this variable is 'false(2)', generation of cmStateNotification is disabled. The default value is 'false(2)'. ...

cmSystemInfoGroup

A collection of objects providing system configuration and status information.

cmGroupInfoGroup

A collection of objects providing modem configuration and statistics information for modem groups.

cmLineInfoGroup

A collection of objects providing modem configuration and statistics information for individual modem.

cmManagedLineInfoGroup

A collection of objects providing modem configuration and statistics information for individual managed modems.

cmLineSpeedInfoGroup

A collection of objects providing modem configuration and statistics information for individual managed modems.

cmSystemInfoGroupRev1

A collection of objects providing system configuration and status information.

cmLineSpeedInfoGroupRev1

A collection of objects providing modem configuration and statistics information for individual managed modems.

cmManagedLineInfoGroupRev1

A collection of objects providing modem configuration and statistics information for individual managed modems.

cmNotificationConfigGroup

Objects for configuring the notification behavior of this MIB. ::= { ciscoModemMgmtMIBGroups 9 } cmNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { cmStateNotification } STATUS current DESCRIPTION The collection of notifications used for monitoring mo ...

cmLineSpeedInfoGroupRev2

A collection of objects providing modem configuration and statistics information for individual managed modems.

cmManagedLineInfoGroupRev2

A collection of objects providing modem configuration and statistics information for individual managed modems.