DLINK-AGENT-MIB Download

agentMgmtProtocolCapability

The network management protocol(s) supported by this agent.

agentMibCapabilityTable

A list of MIB capability entries supported by this agent.

agentMibCapabilityEntry

A MIB capability entry contains objects describing a particular MIB supported by this agent.

agentMibCapabilityIndex

A list of agentMibCapabilityDescr entries.

agentMibCapabilityDescr

The name of the MIB supported by the agent.

agentMibCapabilityVersion

The version of the MIB specified in this entry.

agentMibCapabilityType

The type of the MIB specified in this entry.

agentStatusConsoleInUse

This indicates whether console is currently in-use.

agentStatusSaveCfg

This indicates the status of the device configuration. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. proceeding(2) - the device configuration is being currently ...

agentStatusFileTransfer

-- "status of firmware download control. If the value is 'other', -- means never firmware updated since device started up. Time scale is 5 seconds.The value will be between 0%(idle) and 100% (very busy).

agentCPUutilizationIn1min

Time scale is 1 minute.The value will be between 0%(idle) and 100% (very busy).

agentCPUutilizationIn5min

Time scale is 5 minute.The value will be between 0%(idle) and 100% (very busy).

agentBscSwFileTable

A list of MIB Basic Config entries supported file Update by this agent.

agentBscSwFileEntry

A basic config entry contains objects describing a particular MIB supported by this agent.

agentBscSwFileIndex

The table index for the file entry

agentBscSwFileDscr

The description for the purpose of the software file in this entry. Note: For system which does not support change of this object, setting value to this object will cause the system to return bad-value error message. ::= { agentBscSwFileEntry 2 } SYNTAX ...

agentBscSwFileTransferType

The channel through which the file will be downloaded or uploaded. Note: For system which does not support all channels, setting value to the unsupported channel will cause the system to return bad-value error message. ::= { agentBscSwFileEntry 4 } SYNTAX ...

agentBscSwFileLocateId

-- "This object describes the type of the file. -- runtime-code(1), -- log-file(2), -- cfg-file(3) -- Note: -- For system which does not support change of this object, setting value to -- this object ...

agentFileTransfer

This object will execute the download or upload action. If start(2), it will begin to download/upload, but no reset as follow. If start-and-reset(3), then the reset will active after download or upload. No action if(4). Note: Because these funiction will ...

agentSystemReset

This object indicates the agent system reset state. Setting this object to no-reset(4) has no effect. Setting this object to cold-start(2) or warm-start(3) will reset the agent. The agent always returns no-reset(4) when this object is read.

agentRs232PortConfig

This object indicates the RS-232C mode while device restart.

agentOutOfBandBaudRateConfig

This object allows user to specify out_of_band baud rate. It will take effect when the system is restart. Note: Because these funiction will be limited by the system support. Some of the select item will invalid. When one of the item user select,it will r ...

agentIpNumOfIf

The total number of IP interfaces supported by this agent.

agentIpTftpServerAddr

The IP Address of TFTP Server.

agentIpGetIpFrom

This object indicates whether the agent get its system IP address from Bootp/DHCP server at start up.

systemSeverityTrapControl

Indicate the level of system severity control,The system has a severity level control and each trap should be along with a severity control. When trap event occurs and its severity is higher than the system severity control level, the trap works as it de ...

systemSeverityLogControl

Indicate the level of system severity control,The system has a severity level control and each log should be along with a severity control. When log event occurs and its severity is higher than the system severity control level, the log works as it defin ...