MLD-SNOOPING-MIB Download
The Structure of MLD snooping management for the
proprietary enterprise.
IPHost Network Monitor offer an easy way of SNMP monitoring your D-Link Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for MLD-SNOOPING-MIB
- swMldSnoopingGlobalState
- This object indicates Mld snooping capture function is enabled or disabled.
- swMldSnoopingMcstRTOnly
- Specifies that the switch should forward all multicast traffic to a multicast-enabled IPv6 router only.
- swMldSnoopingMaxSupportedVlans
- Maximum number of Vlans in the Mld snooping table (swMldSnoopingCtrlTable).
- swMldSnoopingCtrlTable
- The table controls the Vlan's MLD function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up ...
- swMldSnoopingCtrlEntry
- The entry in MLD control table (swMldSnoopingCtrlTable). The entry is effective only when MLD capture switch (swMldSnoopingGlobalState) is enabled.
- swMldSnoopingCtrlVid
- This object indicates the MLD control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setti ...
- swMldSnoopingQueryInterval
- The frequency at which MLD Host-Query packets are transmitted on this switch.
- swMldSnoopingMaxResponseTime
- The maximum query response time on this switch.
- swMldSnoopingRobustness
- The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. MLD is robust to (Robustness Variable-1) packet losses.
- swMldSnoopingLastMemberQueryInterval
- The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
- swMldSnoopingHostTimeout
- The timer value for sending MLD query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired.
- swMldSnoopingRouteTimeout
- The Router Timeout is how long a host must wait after hearing a Query before it may send any MLD messages.
- swMldSnoopingDoneTimer
- When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swMldSnoopingDoneTimer to the group being left.
- swMldSnoopingQueryState
- This object decide the MLD query enabled or disabled.
- swMldSnoopingCurrentState
- This object indicates the current MLD query state.
- swMldSnoopingCtrlState
- This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - MLD funtion is disabled for this entry. enable(3) - M ...
- swMldSnoopingFastDoneState
- This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - MLD fast-done funtion is disabled for this ...
- swMldSnoopingVersion
- This object indicates the MLD version of this entry. If the MLD version is configured with a lower version, the higher version's MLD Report/Leave messages will be ignored. ::= { swMldSnoopingCtrlEntry 13 } -- ---------------------------------------------- ...
- swMldSnoopingGroupInfoEntry
- Information about current Mld information which captured by this device, provided that swMldSnoopingGlobalState and swMldSnoopingCtrlState of associated VLAN entry are all enabled.
- swMldSnoopingGroupInfoVid
- This object indicates the Vid of individual MLD table entry. It shows the Vid of MLD report information captured on network.
- swMldSnoopingGroupInfoIpAddr
- This object is identify group ip address which is captured from MLD packet, in per-Vlan basis.
- swMldSnoopingGroupInfoMacAddr
- This object is identify mac address which is corresponding to swMldSnoopingGroupInfoIpAddr, in per-Vlan basis.
- swMldSnoopingGroupInfoPortMap
- This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit re ...
- swMldSnoopingGroupInfoReportCount
- This object indicate how much report packet was receive by our device corresponding with this entry from MLD function enabled, in per-Vlan basis.
- swMldSnpRouterPortsTable
- The table controls the Vlan's MLD router ports function.
- swMldSnpRouterPortsEntry
- The entry in MLD router ports table (swMldSnoopingCtrlTable).
- swMldSnpRouterPortsVid
- This object indicates the MLD router ports entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid ...
- swMldSnpRouterStaticPortList
- Displays router ports that have been statically configured.
- swMldSnpRouterDynamicPortList
- Displays router ports that have been dynamically configured.
- swMldSnpRouterForbiddenPortList
- Displays router ports that have been forbiddenly configured.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
