Nortel-Magellan-Passport-VnetEuroIsdnMIB Download

sigChanEIsdnRowStatusTable

This entry controls the addition and deletion of sigChanEIsdn components.

sigChanEIsdnRowStatusEntry

A single entry in the table represents a single sigChanEIsdn component.

sigChanEIsdnRowStatus

This variable is used as the basis for SNMP naming of sigChanEIsdn components. These components can be added and deleted.

sigChanEIsdnComponentName

This variable provides the component's string name for use with the ASCII Console Interface

sigChanEIsdnStorageType

This variable represents the storage type value for the sigChanEIsdn tables.

sigChanEIsdnIndex

This variable represents the index for the sigChanEIsdn tables.

sigChanEIsdnL2Table

This group specifies the provisionable layer 2 attributes of the Euro ISDN (ETSI-T) protocol.

sigChanEIsdnL2Entry

An entry in the sigChanEIsdnL2Table.

sigChanEIsdnT23

This attribute specifies duration of the layer 2 enable request timer.

sigChanEIsdnT200

This attribute specifies the maximum elapsed time between a layer 2 frame and its acknowledgment.

sigChanEIsdnN200

This attribute specifies the maximum number of re-transmissions of a layer 2 frame.

sigChanEIsdnT203

This attribute specifies the maximum time during which layer 2 frames may be absent. Expiry triggers a check on whether the far end is alive.

sigChanEIsdnCircuitSwitchedK

This attribute specifies the maximum number of sequentially numbered I frames (that is, window size (k)) that may be unacknowledged at any given time for a SAP supporting primary rate (64kbit/sec) signalling.

sigChanEIsdnL3Table

This group represents the provisionable Layer 3 timer attributes of a the Euro ISDN (ETSI-T) protocol.

sigChanEIsdnL3Entry

An entry in the sigChanEIsdnL3Table.

sigChanEIsdnT310

This attribute specifies duration of the call proceeding state timer.

sigChanEIsdnProvTable

This group defines the general options of the D-channel signalling link.

sigChanEIsdnProvEntry

An entry in the sigChanEIsdnProvTable.

sigChanEIsdnSide

This attribute specifies whether the interface is the network or user side of the connection. The parameter applies to both the layer 2 and layer 3 of the interface. In addition, if this attribute is set to network, then the interface is master during cha ...

sigChanEIsdnMaxNonCallConcurrent

This attribute specifies the maximum number of simultaneous active non call-associated sessions that are allowed. Reduction of the value does not impact NCAS sessions already in progress.

sigChanEIsdnOverlapSending

This attribute specifies whether overlap sending to the PBX is enabled.

sigChanEIsdnOverlapReceiving

This attribute specifies whether overlap receiving from the PBX is enabled.

sigChanEIsdnStateTable

This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...

sigChanEIsdnStateEntry

An entry in the sigChanEIsdnStateTable.

sigChanEIsdnAdminState

This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...

sigChanEIsdnOperationalState

This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...

sigChanEIsdnUsageState

This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...

sigChanEIsdnStatsTable

This group provides the statistical attributes for the SigChan/x EuroIsdn component.

sigChanEIsdnStatsEntry

An entry in the sigChanEIsdnStatsTable.

sigChanEIsdnTotalCallsToIf

This attribute counts the total number of calls that have been made to the interface. The value wraps to zero when it exceeds its maximum.

sigChanEIsdnTotalCallsFromIf

This attribute counts the total number of calls that have been made from the interface. The value wraps to zero when it exceeds its maximum.

sigChanEIsdnNonCallAssocSessionsToIf

This attribute counts the total number of non call-associated sessions that have been made to the interface. The value wraps to zero when it exceeds its maximum.

sigChanEIsdnNonCallAssocSessionsFromIf

This attribute counts the total number of non call-associated sessions that have been made from the interface. The value wraps to zero when it exceeds its maximum.

sigChanEIsdnOperTable

This group provides the operational attributes for the SigChan/x EuroIsdn component.

sigChanEIsdnOperEntry

An entry in the sigChanEIsdnOperTable.

sigChanEIsdnActiveChannels

This attribute indicates the number of currently active channels. This includes channels used by both, data and voice calls.

sigChanEIsdnActiveVoiceChannels

This attribute indicates the number of channels that are currently used by voice calls. This includes modem calls.

sigChanEIsdnActiveDataChannels

This attribute indicates the number of channels that are currently used by data calls. This does not include modem data.

sigChanEIsdnPeakActiveChannels

This attribute indicates the maximum value of the activeChannels attribute during the last polling period.

sigChanEIsdnPeakActiveVoiceChannels

This attribute indicates the maximum value of the activeVoiceChannels attribute during the last polling period.

sigChanEIsdnPeakActiveDataChannels

This attribute indicates the maximum value of the activeDataChannels attribute during the last polling period.

sigChanEIsdnDChanStatus

This attribute indicates the state of the D-channel. outOfService means that there is no layer 2 or layer 3 connectivity to the PBX. establishing means that the signalling channel is attempting to stage the layer 2. established means that the layer 2 is e ...

sigChanEIsdnToolsTable

This contains a series of operational attributes which turn on and off several kinds of tracing.

sigChanEIsdnToolsEntry

An entry in the sigChanEIsdnToolsTable.

sigChanEIsdnTracing

This attribute defines which types of tracing are active on the signalling channel. The tracing messages are sent to the debug stream. To see the messages the agentQueueSize attribute of the Lp/x Eng Ds/debug component must be greater than 0 and the opera ...

sigChanEIsdnOptTable

This group specifies the provisionable attributes specific to the Euro ISDN (ETSI-T) protocol.

sigChanEIsdnOptEntry

An entry in the sigChanEIsdnOptTable.

sigChanEIsdnVariant

This attribute specifies the specific variant of the Euro ISDN (ETSI- T) protocol. Supported variants are: etsiGeneric - provides generic ETSI-T protocol. Only proxy of the NETWORK side of the protocol is implemented, austria - provides ETSI-T protocol va ...

sigChanEIsdnConnectServiceTimer

This attribute specifies duration of the 'await connection' supervisory timer which applies to non call-associated sessions providing bearer-independent connection-oriented transport for supplementary services. The timer is started at the ingress Passport ...

sigChanEIsdnResponseServiceTimer

This attribute specifies duration of the 'await response' supervisory timer which applies to non call-associated sessions providing bearer-independent connection-oriented transport for supplementary services. The timer is started at the ingress Passport w ...

sigChanEIsdnLifetimeServiceTimer

This attribute specifies duration of the service lifetime supervisory timer which applies to non call-associated sessions providing bearer-independent connection-oriented transport for supplementary services. The timer limits the duration of a virtual cal ...

sigChanEIsdnFramerRowStatusTable

This entry controls the addition and deletion of sigChanEIsdnFramer components.

sigChanEIsdnFramerRowStatusEntry

A single entry in the table represents a single sigChanEIsdnFramer component.

sigChanEIsdnFramerRowStatus

This variable is used as the basis for SNMP naming of sigChanEIsdnFramer components. These components cannot be added nor deleted.

sigChanEIsdnFramerComponentName

This variable provides the component's string name for use with the ASCII Console Interface

sigChanEIsdnFramerStorageType

This variable represents the storage type value for the sigChanEIsdnFramer tables.

sigChanEIsdnFramerIndex

This variable represents the index for the sigChanEIsdnFramer tables.

sigChanEIsdnFramerProvTable

This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.

sigChanEIsdnFramerProvEntry

An entry in the sigChanEIsdnFramerProvTable.

sigChanEIsdnFramerInterfaceName

This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.

sigChanEIsdnFramerStateTable

This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses ...

sigChanEIsdnFramerStateEntry

An entry in the sigChanEIsdnFramerStateTable.

sigChanEIsdnFramerAdminState

This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this ...

sigChanEIsdnFramerOperationalState

This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that t ...

sigChanEIsdnFramerUsageState

This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value b ...

sigChanEIsdnFramerStatsTable

This group contains the operational statistics data for a Framer component.

sigChanEIsdnFramerStatsEntry

An entry in the sigChanEIsdnFramerStatsTable.

sigChanEIsdnFramerFrmToIf

This attribute counts the number of frames transmitted to the link interface by the Framer. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerFrmFromIf

This attribute counts the number of frames received from the link interface by the Framer. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerOctetFromIf

This attribute counts the number of bytes received from the link interface by the Framer. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerAborts

This attribute counts the total number of aborts received. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerCrcErrors

This attribute counts the total number of frames with CRC errors. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerLrcErrors

This attribute counts the total number of frames with LRC errors. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerNonOctetErrors

This attribute counts the total number of frames that were non octet aligned. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerOverruns

This attribute counts the total number of frames received from the link for which overruns occurred. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerUnderruns

This attribute counts the total number of frames transmitted to the link for which underruns occurred. This count wraps to zero after exceeding its maximum value.

sigChanEIsdnFramerLargeFrmErrors

This attribute counts the total number of frames received which were too large (longer than 500 bytes). This count wraps to zero after exceeding its maximum value.