PIM-SM-MIB Download

swPimSmGlobalState

Used to control PIM-SM state.

swPimRegisterProbeTime

Used to set a time to send a probe message from the Designated Router (DR) to the Rendezvous Point (RP) before the Register Suppression time expires. If a Register Stop message is received by the DR, the Register Suppression Time will be restarted. If no ...

swPimRegisterSuppressionTime

The time interval between receiving a Register-Stop message and restarting the process of sending of register messages again. A lower value represents an increase in register messages being sent to the RP, while a higher value represents a longer latency ...

swPimInfoTable

The PIM Information Table contains PIM related information, such as DR priority.

swPimInfoEntry

An entry in the PIM Information Table.

swPimInfoInterface

The ifIndex value of this PIM interface.

swPimInfoAddress

The IP address of the PIM interface.

swPimInfoNetMask

The network mask for the IP address of the PIM interface.

swPimInfoDesignatedRouter

The Designated Router on this PIM interface. For point-to- point interfaces, this object has the value 0.0.0.0.

swPimInfoHelloInterval

The frequency at which PIM Hello messages are transmitted on this interface.

swPimInfoJoinPruneInterval

The frequency at which PIM Join/Prune messages are transmitted on this PIM interface. The default value of this object is the pimJoinPruneInterval.

swPimInfoDRPriority

The DR Priority sets the priority of an IP interface to become the Designated router for the multiple access network. A numerically larger priority is always preferred, yet a lower number represents a higher priority. A router's knowledge of the current D ...

swPimInfoMode

The configured mode of this PIM interface. A value of sparseDense is only valid for PIMv1.

swPimInfoState

The configured state of this PIM interface.

swpimCbsrBootStrapPeriod

The time interval, in seconds, for Boot Strap Messages originating from the elected BSR.

swPimCbsrHashMaskLen

The length (in bits) of the mask to use for the hash function(This hash algorithm will be used to determine which candidate RP will be the RP for the PIM-SM network.).For IPv4 we recommend a value of 30. For IPv6 we recommand a value of 126.

swPimCbsrTable

The PIM CBSR Table contains the candidate bootstrap router related information, such as interface name, IP address and priority.

swPimCbsrEntry

An entry in the PIM CBSR Table.

swPimCbsrInterface

The ifIndex value of this PIM interface.

swPimCbsrIpAddress

The IP address of this PIM interface.

swPimCbsrSubnetMask

The IP netmask for this PIM interface.

swPimCbsrPriority

The preference value for the local candidate interface to become a bootstrap router. The value of -1 is used to indicate the local candidate interface cannot become the BSR.

swPimCandidateRPHoldtime

Used to set the time CRP advertisements remain valid on the PIM-SM enabled network. If these advertisements, set here, aren't received by the BSR within this time period, the CRP will be removed from the list of candidates. 0 states to the BSR that this C ...

swPimCandidateRPPriority

This value determines the priority of a CRP to become the RP for the distribution tree. A lower value denotes a higher priority. If there is a tie for priority, the device with the highest IP address will become the RP. This information is stored in the B ...

swPimCandidateRPWildcardPrefixCnt

The number of enocded group addresses included in the message; indicating the group prefixes for which the C-RP is advertising. A Prefix-Cnt of '0' implies a prefix of 224.0.0.0 with mask length of 4; i.e. all multicast groups. If the C-RP is not configur ...

swPimCandidateRPTable

The (conceptual) table listing the IP multicast groups for which the local router is to advertise itself as a Candidate-RP when the value of pimComponentCRPHoldTime is non-zero. If this table is empty, then the local router will advertise itself as a Can ...

swPimCandidateRPEntry

An entry (conceptual row) in the pimCandidateRPTable.

swPimCandidateRPGroupAddress

The IP multicast group address which, when combined with pimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.

swPimCandidateRPGroupMask

The multicast group address mask which, when combined with pimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.

swPimCandidateRPInterface

The name of the interface which will be advertised as a Candidate-RP.

swPimCandidateRPRowStatus

The status of this row, by which new entries may be created, or old entries deleted from this table.

swPimNeighborTable

The (conceptual) table listing the router's PIM neighbors.

swPimNeighborEntry

An entry (conceptual row) in the swPimNeighborTable.

swPimNeighborAddress

The IP address of the PIM neighbor for which to find PIM neighbor information.

swPimNeighborIfIndex

The value of ifIndex for the interface used for which to find PIM neighbor information.

swPimNeighborExpiryTime

The minimum time remaining before this PIM neighbor ages out.

swPimRegChksumIncDataTable

The PIM Register Checksum Including Data Table contains the PIM register checksum including data information, such as RP address and state.

swPimRegChksumIncDataEntry

An entry in the PIM Register Checksum Including Data Table.

swL3SwPimRegChksumIncDataRpAddr

Specifies the RP address.

swL3SwPimRegChksumIncDataState

The state of register checksum including data for RPs.

swPimStaticRPTable

The PIM Static RP Table contains the PIM static RP related information, such as group address, group mask, RP address and RP row status.

swPimStaticRPEntry

An entry in the PIM Static RP Table.

swPimStaticRPGroupAddress

The IP multicast group address which, when combined with swPimStaticRPGroupMask, identifies a group prefix for which the local router will advertise itself as a static RP.

swPimStaticRPGroupMask

The multicast group address mask which, when combined with swPimStaticRPGroupAddress, identifies a group prefix for which the local router will advertise itself as a static RP.

swPimStaticRPAddress

The (unicast) address of the interface which will be advertised as a static RP.

swPimStaticRPRowStatus

The status of this row, by which new entries may be created, or old entries deleted from this table.

swPimIpMRouteTable

The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteTable defined in the IP Multicast MIB.

swPimIpMRouteEntry

An entry (conceptual row) in the pimIpMRouteTable. There is one entry, per entry in the ipMRouteTable, whose incoming interface is running PIM.

swPimIpMRouteGroup

The IP multicast group address for which this entry contains multicast routing information.

swPimIpMRouteSource

The network address which, when combined with the corresponding value of ipMRouteSourceMask, identifies the sources for which this entry contains multicast routing information.

swPimIpMRouteSourceMask

The network mask which, when combined with the corresponding value of ipMRouteSource, identifies the sources for which this entry contains multicast routing information.

swPimIpMRouteUpstreamAssertTimer

The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert timer has changed the upstream neighb ...

swPimIpMRouteAssertMetric

The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is received.

swPimIpMRouteAssertMetricPref

The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect.

swPimIpMRouteAssertRPTBit

The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect.

swPimIpMRouteFlags

This object describes PIM-specific flags related to a multicast state entry. See the PIM Sparse Mode specification for the meaning of the RPT and SPT bits.

swPimIpMRouteType

This object describes the PIM-specific type as related to a multicast state entry.

swPimRPSetBootstrapRouter

Specifies a Bootstrap Router.

swPimRPSetTable

The (conceptual) table listing PIM information for candidate Rendezvous Points (CRPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, ...

swPimRPSetEntry

An entry (conceptual row) in the pimRPSetTable.

swPimRPSetComponent

A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.

swPimRPSetGroupAddress

The IP multicast group address which, when combined with pimRPSetGroupMask, gives the group a prefix. This prefix will determine for which entry CRP information is to be displayed, and which entry contains information about the Candidate-RP.

swPimRPSetGroupMask

The multicast group address mask which, when combined with pimRPSetGroupAddress, gives the group a prefix to determine and which entry contains which entry CRP information is to be displayed for which this entry contains information about the Candidate-RP ...

swPimRPSetAddress

The IP address of the Candidate-RP.

swPimRPSetType

The type of a Candidate-RP.