ct-els10-mib Download

sysID

sysReset

sysTrapPort

els10-27hwDiagCode

els10-27hwManufData

els10-27hwPortCount

els10-27hwPortTable

els10-27hwPortEntry

els10-27hwPortIndex

els10-27hwPortType

els10-27hwPortSubType

els10-27hwPortDiagPassed

els10-27hwAddr

els10-27hwUpLink

Specifies whether the Up-Link I/O module is existed

els10-27hwUpLinkManufData

This is a 32-byte array which contains the part number, serial number, and hardware revision level of the Up-Link I/O module. This array is valid only when the els10-27hwUplink is true. If els10-27hwUplink is false, it returns an error

els10-27swNumber

els10-27swFilesetTable

els10-27swFilesetEntry

els10-27swIndex

els10-27swDesc

els10-27swCount

els10-27swType

els10-27swSizes

els10-27swStarts

els10-27swBases

els10-27swFlashBank

els10-27adminFatalErr

Information about last reset: First byte, cause of reset, values: 00: power failure 01: WatchDog Timeout 02: Software Reset 03: NMS Shutdown 04-255: Fatal Error Second byte, Hw/Sw component that failed Remaining bytes, description of fault.

els10-27adminAnyPass

els10-27adminGetPass

els10-27adminNMSIPAddr

els10-27adminStorageFailure

els10-27adminAuthenticationFailure

els10-27adminNAMReceiveCongests

els10-27adminArpEntries

els10-27adminArpStatics

els10-27adminArpOverflows

els10-27adminIpEntries

els10-27adminIpStatics

els10-27adminStaticPreference

els10-27adminRipPreference

els10-27adminRipRouteDiscards

els10-27adminRebootConfig

els10-27adminDisableButton

els10-27adminButtonSelection

els10-27adminLEDProgramOption

els10-27swdisDesc

The description (0-32 bytes) of the software set currently being downloaded, or a description of the software set last downloaded since the FN1026 booted.

els10-27swdisAccess

The version of software that may be downloaded. Attempts to download other versions of software will be rejected. The value for swdisAccess is embedded within the software files that are to be distributed via TFTP. Its value may be derived from the names ...

els10-27swdisWriteStatus

The status of the erase/write operation.

els10-27swdisConfigIp

The IP address of the NMS (i.e., any IP host) that is allowed to use TFTP to send/retrieve the configuration file of the FN1026. A value of 0.0.0.0 (which is the factory specified default) prevents any NMS from obtaining access, while a value of 255.255.2 ...

els10-27swdisConfigRetryTime

The number of seconds that the FN1026 will wait for an acknowledgment before it retransmits an unacknowledged TFTP data block. The factory specified default is 5 seconds.

els10-27swdisConfigTotalTimeout

The number of seconds that the FN1026 will wait for an acknowledgment to a data block before it cancels a TFTP session. The factory specified default is 25 seconds.

els10-27addrStatics

els10-27addrDynamics

els10-27addrDynamicMax

els10-27addrDynamicOverflows

els10-27addrFlags

els10-27addrMAC

els10-27addrPort

els10-27addrOperation

els10-27addrIndex

els10-27addrNext

els10-27addrBlockSize

els10-27addrBlock

els10-27ifTable

els10-27ifEntry

els10-27ifIndex

els10-27ifThresholdTime

els10-27ifRxQueueThresh

els10-27ifRxQueueThreshTime

els10-27ifTxStormCnt

els10-27ifTxStormTime

els10-27ifFunction

els10-27ifRxHwFCSs

els10-27ifRxQueues

els10-27ifStatisticsTime

els10-27ifForwardedChars

els10-27ifDescr

els10-27ifGoodRxFrames

els10-27ifGoodTxFrames

els10-27dot3Table

els10-27dot3Entry

els10-27dot3Index

els10-27dot3TPLinkOK

els10-27dot3LedOn

els10-27dot3RxCollisions

els10-27dot3RxRunts

els10-27dot3RxLateColls

els10-27dot3TxJabbers

els10-27dot3TxBabbles

els10-27dot3TxCollisions

els10-27dot3SpeedSelection

els10-27dot3DuplexSelection

els10-27uartTable

els10-27uartEntry

els10-27uartIndex

els10-27uartBaud

els10-27uartAlignmentErrors

els10-27uartOverrunErrors

els10-27debugStringID

els10-27debugString

els10-27debugTable

els10-27debugEntry

els10-27debugIndex

els10-27debugOperation

els10-27debugBase

els10-27debugLength

els10-27debugData

els10-27lpbkTable

els10-27lpbkEntry

els10-27lpbkIndex

els10-27lpbkOperation

els10-27lpbkDestAddr

els10-27lpbkPktNum

els10-27lpbkInterval

els10-27lpbkPktLength

els10-27lpbkIncrements

els10-27lpbkGoods

els10-27lpbkErrorNoReceives

els10-27lpbkErrorBadReceives

els10-27lpbkErrorSize

els10-27lpbkErrorSent

els10-27lpbkErrorReceived

els10-27lpbkErrorOffset

els10-27protoTable

This table contains configuration information specify- ing the types of protocols used to bridge, route, translate, and filter frames for each port.

els10-27protoEntry

Each entry in this table specifies which protocols are used by a particular port in the ES/1.

els10-27protoIfIndex

Identifies the interface (port) to which this entry's information belongs. The value of this variable corresponds to ifIndex, as well as most of the other port identification values in related MIBs.

els10-27protoBridge

Defines the bridging method to be applied to frames received at, or destined for, this port. Ethernet and FDDI ports may be configured for transparent, srt, or none. Token Ring ports may be configured for any of the four options. The UART may only be con ...

els10-27protoSuppressBpdu

Allows transmission of spanning tree protocol packets to be suppressed. If normal(1), 802.1d spanning tree packets are transmitted as usual. If suppressed(2), these packets are not transmitted. This option may be needed for in- teroperability with non-80 ...

els10-27protoRipListen

Specifies whether the port should listen for internet Routing Information Protocol (RFC-1058) packets, in order to build the routing table for the unit.

els10-27protoTrunking

Specifies whether SMC's trunking protocol (an extension to the standard Spanning Tree) is to be used over this port.

els10-27sprotoTransmitPacing

When enabled, introduces delays into normal transmission of frames, to reduce the probability of collisions during heavy traffic.

els10-27trunkTable

This table describes the trunking status and attributes of the interfaces that are configured for bridge trunking.

els10-27trunkEntry

An entry exists in this table for each physical interface (port) that is configured for trunking.

els10-27trunkIfIndex

Identifies a physical interface (port) which is configured for LAN trunking. The value of this variable corresponds to ifIndex, as well as most of the other port identification values in related MIBs.

els10-27trunkState

If off(1) then this link has not been enabled for trunking. If closed(2) then this link has not yet received any Trunking PDUs. If oneway(3) then incoming Trunking PDUs do not indicate that our PDUs are being successfully received by the far end. If joine ...

els10-27trunkRemoteBridgeAddr

The MAC address portion of the bridge ID of the remote bridge.

els10-27trunkRemoteIp

The IP address of the remote bridge, as reported by that bridge for administrative purposes.

els10-27trunkLastError

The last reason for failure when the link is in closed, oneway, or helddown state.

els10-27trunkLinkOrdinal

The position of this link within the trunk group.

els10-27trunkLinkCount

The number of links within the trunk group.

els10-27trunkLastChange

The number of seconds since els10-27trunkState changed.

els10-27WorkGroupNextNumber

The next available workgroup number to be used. When creating a new workgroup, it is recommended to read the value of the variable and use it to key into the workgroup table.

els10-27WorkGroupCurrentCount

The total number of workgroups currently defined.

els10-27WorkGroupMaxCount

The maximum number of workgroups allowed.

els10-27WorkGroupTable

This table contains work group definitions for the interfaces.

els10-27WorkGroupEntry

Each entry in this table contains a definition of a work group.

els10-27WorkGroupNumber

An integer that identifies the work group, used as an index to this table.

els10-27WorkGroupName

A 1-16 character work group name.

els10-27WorkGroupPorts

A list of all ports within the group. The first octet specified ports 1-8, the second 9-16, etc.

els10-27WorkGroupType

The type of work group: all - no additional information needs to be supplied.

els10-27trapControlTable

This table contains information about the severity of each trap and whether the trap is currently enabled.

els10-27trapControlEntry

els10-27trapIndex

The specific trap number.

els10-27trapEnabled

Enable or disable the generation of this trap.

els10-27trapSeverity

A user-definable severity, indicating the importance of the trap.

els10-27trapText

A description of the trap.

els10-27trapSeverityControlTable

This table contains information about whether a class of traps of a particular severity are enabled or disabled.

els10-27trapSeverityControlEntry

els10-27trapSeverityControlSeverity

A user-definable severity, indicating the importance of the trap.

els10-27trapSeverityEnable

Enable or disable all traps of a given severity level.

els10-27trapIncludeText

Whether or not a formatted text string is included in the trap PDU.

els10-27trapTime

The time, in centiseconds, which should expire between the sending of traps.

els10-27trapRetry

The number of times any enterprise-specific trap is to be sent for a given event. PDUs are retried using a truncated exponential backoff: 2 seconds, 4 seoncs, 8 seconds, 16 seconds, and then 32 seconds for all succeeding intervals.

els10-27trapNumber

The number of traps that are in the els10-27trapTable.

els10-27trapTable

This table contains the latest traps that have been generated.

els10-27trapEntry

els10-27trapEntryIndex

A number representing the order in which the trap occurred in time. This 32 bit number can wrap.

els10-27trapEntryTimeStamp

The time at which the trap occurred.

els10-27trapEntryText

A description of the trap.

els10-27trapEntryNumber

The specific trap number, as specified in the TRAP PDU.

els10-27trapEntrySeverity

A user-definable severity, indicating the importance of the trap.

els10-27pingDataTimeout

The time, in centiseconds, from the last ping activity (a send or receive of an ECHO_RESPONSE or ECHO_REQUEST message), to when the els10-27pingEntry information for that ping request will be deleted.

els10-27pingTable

The set of information describing the active ping requests and their results.

els10-27pingEntry

The parameters, state, and results of a ping request.

els10-27pingNMSAddr

The IP address of the NMS, used to determine which ping request to return information on.

els10-27pingDestAddr

The IP address which is to be the destination of the ping ECHO_REQUEST. This variable cannot be set while els10-27pingOperation is on.

els10-27pingState

The current state of the ping request.

els10-27pingCount

The number of ping requests which are to be sent. This variable cannot be set while els10-27pingOperation is on.

els10-27pingDataSize

The datagram packet size which will be sent with the ECHO_REQUEST, in bytes. This variable cannot be set while els10-27pingOperation is on.

els10-27pingWait

The time, in centiseconds, between the sending of each ECHO_REQUEST message. This variable cannot be set while els10-27pingOperation is on.

els10-27pingTimeOut

The time, in centiseconds, since the last ECHO_RESPONSE was received (or the last ECHO_REQUEST was sent, if there have been no responses) when the ping request will time out. This variable cannot be set while els10-27pingOperation is on.

els10-27pingOperation

Setting els10-27pingOperation to on will begin the ping request. Setting els10-27pingOperation to off will terminate the ping request.

els10-27pingMin

The minimum round trip time for the ping requests and responses, in centiseconds.

els10-27pingMax

The maximum round trip for the ping requests and responses, in centiseconds.

els10-27pingAvg

The average round trip time for the ping requests and responses, in centiseconds.

els10-27pingNumTransmitted

The number of ICMP ECHO_REQUEST messages that have been transmitted during this ping request.

els10-27pingNumReceived

The number of ICMP ECHO_RESPONSE messages that have been received as a result of this ping request.

els10-27traceDataTimeout

The time, in centiseconds, from the last traceroute activity (the response to or timeout of the last probe sent), to when the els10-27traceEntry information for that traceroute request will be deleted.

els10-27traceTable

The set of information describing the active traceroute requests and their results.

els10-27traceEntry

The parameters, state, and results of a traceroute request.

els10-27traceNMSAddr

The IP address of the NMS, used to determine which traceroute request to return information on.

els10-27traceDestAddr

The IP address which is to be the destination of the traceroute request.This variable cannot be set while els10-27traceOperation is on.

els10-27traceMaxTTL

The maximum time-to-live for outgoing traceroute probe packets. This determines the number of hops that can be in a traceroute. This variable cannot be set while els10-27traceOperation is on.

els10-27traceDataSize

The size of the datagram sent with each probe. This variable cannot be set while els10-27traceOperation is on.

els10-27traceNumProbes

The number of probes which are sent for each hop. This variable cannot be set while els10-27traceOperation is on.

els10-27traceWait

The time to wait in response to a probe. This variable cannot be set while els10-27traceOperation is on.

els10-27traceOperation

Setting els10-27traceOperation to on will begin the traceroute request. Setting els10-27traceOperation to off will terminate the traceroute request.

els10-27traceHop

The hop count for a set of probes with a particular TTL.

els10-27traceHopAddr

The IP address of the host which responded for a probe with a particular TTL.

els10-27traceProbe

The probe instance for a particular hop.

els10-27traceState

The current state of the trace probe.

els10-27traceTime

Round trip time of a probe for a particular hop.

els10-27volmirrorMode

To turn port mirroring on or off.

els10-27volmirrorPort

The number of the port whose data will be mirrored to a special monitor or analyzer port.

els10-27volmonitorPort

Identifies the monitor or analyzer port to receive frames from the special mirror port.

els10-27volMirrorMacTable

A table that contains information for the mirroring on MAC addresses.

els10-27volmirrorMacEntry

Information about specific unicast MAC addresses for which mirroring will act upon.

els10-27volmirrorIndex

Entry Index

els10-27volmirrorMac1

First MAC address for mirroring.

--els10-27volmirrorMac2

-- " Second MAC address for mirroring. -- " Third MAC address for mirroring. -- " Fourth MAC address for mirroring. Specifies the version IEEE 802.1Q VLAN that has been implemented to.

els10-27VlanOperatingMode

Selects the mode of operation. The switch can operate as simply an 802.1d switch, or an 802.1d switch with IEEE VLAN capability (802.1Q). A read of this object will return the current operating mode.

els10-27VlanResetDefaults

To reset the specified bridge. The filtering database is cleared and initialized with the entries specified in the Permananent database, and the Bridge protocol Entity is initialized. While initializing a read will return a value of reset (2). While op ...

els10-27VlanGVRPEnable

If the switch is operating in 802.1Q mode, this selects whether GVRP protocol messages should be processed and VLANs configured accordingly for each port on the switch. Each octet within the value of this object specifies a set of eight ports, with the fi ...

els10-27VlanAccessList

A list of ports that should act as 'Access Ports'. These ports will strip all tags on egress and also make use of a shared database that will automatically be kept by the firmware. Each octet within the value of this object specifies a set of eight ports ...

els10-27VlanNumActiveEntries

The number of active VLAN entries for the device. This includes both static and dynamic VLANs.

els10-27VlanNumConfiguredEntries

The number of configured VLAN entries for the device.

els10-27VlanMaxNumEntries

The maximum number of VLAN entries for the device.

els10-27VlanConfigTable

This table allows for the creation, deletion, and modification of specific VLANs. The ports defined within this group will be members of the 'member set' as defined in the IEEE 802.1Q specification.

els10-27VlanConfigEntry

Allows for configuration of specific VLAN entries.

els10-27VlanConfigIndex

The interface being configured.

els10-27VlanConfigVID

The 12 bit VLAN Identifier associated with the configured VLAN.

els10-27VlanConfigPorts

Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the next octet specifying ports 9 through 16, etc. Within each octet, the least significant bit represents the lowest numbered p ...

els10-27VlanConfigIP

The IP address to be used to access the unit on this Vlan. This must be a valid host address.

els10-27VlanConfigIPMask

The IP subnet mask to be used with this Ip address.

els10-27VlanConfigName

The ASCII name associated with the configured VLAN. A set of this object prior to creating an entry by setting els10-27VlanEstablish will fail with a NO-INSTANCE error.

els10-27VlanConfigStatus

A set with the value of enable(1), enables all associated entries in els10-27VlanConfigVID table for the specified VLAN. A set of disable(2), disables all els10-27VlanConfigVID entries associated with the specified VLAN. A set of this object prior to cr ...

els10-27VlanConfigEstablish

A set of the value create(1), causes an entry to be created in the els10-27VlanConfigTable as specified by the instancing information of els10-27VlanConfigVID, els10-27VlanConfigName, and els10-27VlanConfigPorts. A set of delete(2) causes the specified en ...

els10-27VlanConfigEgressTable

This table allows for the specifying of the default VLAN ID for a specific port. If NOT configured as an 'Access' port, then packets containing this VLAN ID will have the tag stripped on egress. This will set the PVID for each port contained within the l ...

els10-27VlanConfigEgressEntry

Allows for configuration of specific VLAN entries.

els10-27VlanEgressIndex

The index into the Vlan table. A port must be a member of this Vlan prior to assigning this Id as the default.

els10-27VlanEgressVID

The 12 bit VLAN Identifier associated with the configured VLAN.

els10-27VlanEgressList

The set of ports to which traffic destined for the VLAN specified by els10-27VlanEgressVID on the device will have this tag stripped on egress. Each octet within the value of this object specifies a set of eight ports, with thee first octet specifying po ...

els10-27VlanEgressStatus

A set with the value of enable(1), enables all associated entries in els10-27VlanEgressVID table for the specified VLAN. A set of disable(2), disables all els10-27VlanEgressVID entries associated with the specified VLAN. A set of this object prior to cr ...

els10-27VlanFilterGVRPTable

This table allows for the specifying of VLAN ID's that will be resticted from being learnt by the device. If a GVRP packet is received specifying this VLAN ID, it will be ignored.

els10-27VlanFilterGVRPEntry

Allows for configuration of specific entries.

els10-27VlanFilterGVRPIndex

The index into the Vlan Filter table. A maximum of 32 Vlan ID can be restricted from being learnt via GVRP.

els10-27VlanFilterGVRPVID

The 12 bit VLAN Identifier associated with the configured VLAN.

els10-27VlanFilterGVRPList

The set of ports that will be restricted from leaning of a VLAN ID from a GVRP message. The VLAN ID is specified by els10-27VlanFilterGVRPVID. Each octet within the value of this object specifies a set of eight ports, with thee first octet specifying po ...

els10-27VlanFilterGVRPStatus

A set with the value of enable(1), enables all associated entries in els10-27VlanFilterGVRPVID table for the specified VLAN. A set of disable(2), disables all els10-27VlanFilterGVRPVID entries associated with the specified VLAN. A set of this object pri ...

els10-27VlanFilterGVRPEstablishVID

A set of the value create(1), causes an entry to be created in the els10-27VlanFilterGVRPTable as specified by the instancing information of els10-27VlanFilterGVRpVID, and els10-27VlanFilterGVRPPorts. A set of delete(2) causes the specified entry to be r ...

els10-27VlanStaticTable

Allows for configuration of specific VLAN/MAC Address entries and to specify the port to which traffic destined for this address pair should be forwarded. These entries will not be aged out of the forwarding data base.

els10-27VlanStaticEntry

Allows for specifying specific entries.

els10-27VlanStaticVID

The 12 bit VLAN Identifier associated with the configured VLAN.

els10-27VlanStaticMAC

The media dependent physical address.

els10-27VlanStaticPort

An integer designating the port number to associate this address to.

els10-27VlanStaticEstablish

A set of the value create(1), causes an entry to be created as specified by the instancing information of els10-27VlanSaticVID, els10-27VlanStaticMAC, and els10-27VlanStaticPorts. A set of delete(2) causes the specified entry to be removed from thetable. ...

els10-27IPMulticastStatus

Parameter to enable or disable IP multicast filtering on the device. When enabled, the device will examine IP Multicast data packets and dynamically set up filter ports to prevent flooding. The default is disabled.

els10-27ipmInterfaceRtr

Parameter to enable or disable the inclusion of this interface in all Multicast filters. When enabled, all IP Multicast packets for all group filters will be transmitted over this interface. Value is a bit mask.

els10-27igmpStatus

Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. The default is enabled.

els10-27igmpQueryStatus

Parameter to enable or disable the device to act as a Querier. If enabled, the device will send out a Query as a Proxy to solicit reports. The device will not become an IGMP router. The default is disabled.

els10-27igmpQueryCount

Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports (default is 5).

els10-27igmpPortDelay

Timeout value (mins) between IGMP Reports or IGMP Queries received on a port before the system times out the entry from the Multicast Address Filter (default is 5 minutes).

els10-27igmpCacheTable

The (conceptual) table listing the IP multicast groups for which there are members on a particular interface.

els10-27igmpCacheEntry

An entry (conceptual row) in the els10-27igmpCacheTable.

els10-27igmpCacheAddress

The IP multicast group address for which this entry contains information.

els10-27igmpCacheIfIndex

The interface for which this entry contains infor- mation for an IP multicast group address.

els10-27igmpCacheExpiryTime

The minimum amount of time remaining before this entry will be aged out.

els10-27FlowControlBackPressure

Control back pressure on a system wide basis. On (1), Off (2)

els10-27FlowControlThresholdValue

A value specified as a percent of the available buffers. When fewer than the percent of the avaialable buffers is detected, flow control will be initiated. Flow control will cease when the free buffer count meets or exceeds this percent.

els10-27FlowControlPauseInteval

A value between 10 and 65535. Each pause interval is equal to '5.12 microseconds'. A value of 10 will equal '51.2 microseconds'.

els10-27FlowControlTable

Provides a list of control objects over flow control parameters.

els10-27FlowControlEntry

Defines a particular entry containing objects pertaining to definition and control over flow control ports.

els10-27FlowControlInterface

The MIB2 interface for which this flow control information pertains

els10-27FlowControlEnable

Control 802.3x flow control on a per interface basis. On (1), Off (2)

els10-27FlowControlRxPauseFrames

The number of pause frames received on this interface.

els10-27FlowControlTxPauseFrames

The number of pause frames transmitted on this interface.