ctron-bdg-mib Download

bdgdeviceDisableBdg

Indicates if the bridge will be disabled.

bdgdeviceRestoreSettings

Restore the following settings to their default values: Bridge Name to ETHERNET_BRIDGE, Location to LOCAL, Port 1 Name to PORT_1, Port 2 Name to PORT_2, Port 1 Network Name to LAN_1, Port 2 Network Name to LAN_2, Ageing Time for Acquired Database to 300 s ...

bdgdeviceBdgName

The user-defined name (up to 32 characters long) of the bridge. The default bridge name is ETHERNET_BRIDGE.

bdgdeviceNumPorts

The number of ports present on the bridge.

bdgdeviceType

The type of bridge, NB25E, IRBM, or NB20E.

bdgdeviceVersion

The release version of the firmware installed in the bridge.

bdgdeviceLocation

The user-defined name to indicate the location of the bridge on the network. The default location name is LOCAL.

bdgdeviceStatus

The status of the bridge, ON-LINE, STAND BY or DISABLED.

bdgdeviceRestartBdg

Force the bridge to undergo a software reset.

bdgdeviceFrFwd

The number of frames forwarded by the bridge.

bdgdeviceFrRx

The number of frames received by the bridge.

bdgdeviceFrFlt

The number of frames filtered by the bridge.

bdgdeviceErr

The total number of network errors that have occurred.

bdgdeviceSwitchSetting

Indicates the current switch settings read from the bridge hardware.

bdgdeviceNumRestarts

The number of times the bridge has been powered up or restarted.

bdgdeviceTypeFiltering

The type of filtering to be performed by the bridge. The default is IEEE 802.1.

bdgdeviceSTAProtocol

The spanning tree algorithm under which the bridge is operating. The selections are as follows: - IEEE 802.1 compliant spanning tree algorithm environment (802.1) - DEC LAN Bridge 100 environment (DEC) - Without the spanning tree algorithm enabled (NONE) ...

bdgdeviceBridgeID

The unique identifier of the bridge. The first two bytes of the identifier are the bridge priority and the last six bytes are the Ethernet address.

bdgdeviceTopChgCnt

The number of times the bridge's Topology Change Flag has been changed since the bridge was powered up or initialized.

bdgdeviceRootCost

The cost of the path to the root from this bridge.

bdgdeviceRootPort

The port identifier for the port which offers the lowest cost path to the root, i.e. that port for which the sum of the values of the designated cost and path cost parameters held for the port is lowest.

bdgdeviceHelloTime

The time interval between the transmission of Configuration BPDU's by a bridge which is attempting to become the root or is the root.

bdgdeviceBdgMaxAge

The value of the Max Age parameter when the bridge is the root or is attempting to become the root. A time of 6 to 40 seconds is allowed. The default is 20 seconds.

bdgdeviceBdgFwdDly

The value of the forward delay parameter when the bridge is the root or is attempting to become the root. A time of 4 to 30 seconds is allowed.

bdgdeviceTimeTopChg

The time in seconds that has elapsed since the bridge's Topology Change Flag last recorded the value of a topology change.

bdgdeviceTopChg

Indicates if a bridge topology change is in progress.

bdgdeviceDesigRoot

The unique identifier of the bridge recorded as the root.

bdgdeviceMaxAge

The maximum age of received protocol information before it is discarded.

bdgdeviceHoldTime

The minimum time period elapsing between the transmission of configuration BPDU's through a given bridge port.

bdgdeviceFwdDly

The time spent in the listening state while moving from the blocking state to the learning state, or the time spent in the learning state while moving from the listening state to the forwarding state.

bdgdeviceBdgHello

The value of the Hello Time parameter when the bridge is the root or is attempting to become the root. A time of 1 to 10 seconds is allowed. The default is 2 seconds.

bdgdeviceBdgPriority

The part of the bridge address that contains the identifier used in the spanning tree for priority comparisons. Allowed range is 0 through FFFF. The default is 8000.

bdgdeviceResetCounts

Reset all counters to zero.

bdgdeviceUptime

The time, in seconds, that has elapsed since the bridge was last reset or initialized.

bdgdeviceTrapType

Contains the object identifier of the first VarBinding in the last trap generated by the bridge.

bdgPortAddress

The Ethernet address of the port.

bdgPortName

The user-defined name assigned to the port. The default port 1 name is PORT_1 and the default Port 2 name is PORT_2.

bdgPortType

The IEEE specification the port meets, e.g. 802.3.

bdgPortStatus

The status in which the port is operating. The status messages for Ports 1 and 2 are: OFF - The port is off, due to a failed network interface chip associated with that port. OK/SQE ON - The port is communicating with the network and the transceiver makin ...

bdgPortNetName

The user-defined name assigned to a network segment connected to the port. The default network name for Port 1 is LAN_1 and the default network name for Port 2 is LAN_2.

bdgPortFrRx

The number of frames received at the specified port.

bdgPortDisInb

The total number of valid frames that were received at the port but then discarded by the bridge in the forwarding process.

bdgPortFwdOutb

The number of frames forwarded successfully to the appropriate port.

bdgPortDisLOB

The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data.

bdgPortDisTDE

The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was possible.

bdgPortDisErr

The number of frames that could not be transmitted because the frame was too large for the attached network (1526 bytes, including preamble, for 802.3 networks).

bdgPortColl

The number of collisions that have occurred on the network at the specified port.

bdgPortTxAbrt

The number of transmissions that have been aborted due to excessive collisions (over 16 attempts to transmit the same packet).

bdgPortOowColl

The number of collisions out of the standard collision window (51.2 uS). This indicates a network problem.

bdgPortCRCErr

The number of packets detected with Cyclical Redundancy Check failures.

bdgPortFrAlErr

The number of errors due to misaligned packets.

bdgPortPriority

The part of the port identifier which is used with the spanning tree algorithm when determining which port in a LAN segment has priority. The default is 80.

bdgPortState

The current state of the port, DISABLED, LISTENING, LEARNING, FORWARDING or BLOCKING.

bdgPortPathCost

The contributory cost of the applicable port to the overall cost of the path when the specified port is the root port. Allowable range is 1 to 65535. The default is 100.

bdgPortDesigCost

The cost of the path of this port to the root bridge on the network.

bdgPortDesigBrdg

The network address of the bridge that is assumed to be the root bridge on the network.

bdgPortDesigPort

The port identifier of the bridge port believed to be the designated port for the LAN associated with the port.

bdgPortTopChgAck

The value of the topology change acknowledgement flag in the next configuration BPDU to be transmitted on the associated port.

bdgPortDesigRoot

The unique bridge identifier of the bridge that is assumed to be the root bridge on the network.

bdgPortRuntPackets

The number of packets received at the indicated bdgPort that were less than the IEEE 802.3 minimum Ethernet frame size of 64 bytes.

bdgPortOversizePackets

The number of packets received at the indicated port that were greater than the IEEE 802.3 maximum Ethernet frame size of 1518 bytes.

bdgPortFrFilt

The number of frames received at the indicated port that were filtered by the bridge.

acqTotalEntries

The total number of entries in the acquired database.

acqMaxEntries

The maximum number of entries allowed in the acquired database.

acqStaticEntries

The number of addresses added to the Acquired database by the user or network manager.

acqStaticAgeTime

The length of time allowed for a static entry in the Acquired database to be inactive before it is dropped from the database. This time is fixed at zero.

acqDynEntries

The number of entries that have been accumulated in the Acquired database through the bridge's learning process.

acqDynAgeTime

The length of time allowed for a dynamic entry in the acquired database to be inactive before it is dropped from the database. A time from 10 - 1,000,000 seconds is allowed. The default is 300 seconds.

acqEraseDatabase

Set to zero to erase all entries in the acquired database.

acqCreate00

Add an entry to the acquired database to filter packets entering ports 1 and 2 if those packets are destined for the specified address.

acqCreate20

Add an entry to the acquired database to forward packets entering port1 to port2 and filter packets entering port2 if those packets are destined for the specified address.

acqCreate01

Add an entry to the acquired database to filter packets entering port 1 and forward packets entering port 2 to port 1 if those packets are destined for the specified address.

acqCreate21

Add an entry to the acquired database to forward packets entering port 1 to port 2 and to forward packets entering port 2 to port 1 if those packets are destined for the specified address.

acqDelete

Delete an entry from the acquired database.

acqDispType

Display the entry type, STATIC or DYNAMIC.

acqDispOutp1

The outbound port for packets entering port 1.

acqDispOutp2

The outbound port for packets entering port 2.

acqSrcAddress

The source address of this acquired database entry, i.e. the instance.

permMaxEntries

The maximum number of entries allowed in the permanent database.

permCurrEntries

The number of entries currently recorded in the bridge's permanent database.

permEraseDatabase

Erase all entries in the permanent database.

permCreate00

Add an entry to the permanent database to filter packets entering ports 1 and 2 if those packets are destined for the specified address.

permCreate20

Add an entry to the permanent database to forward packets entering port 1 and filter packets entering port 2 if those packets are destined for the specified address.

permCreate01

Add an entry to the permanent database to filter packets entering port 1 and forward packets entering port 2 if those packets are destined for the specified address.

permCreate21

Add an entry to the permanent database to forward packets entering ports 1 and 2 if those packets are destined for the specified address.

permDelete

Delete an entry from the permanent database.

permDispType

Display the entry type, STATIC or DYNAMIC.

permDispOutp1

The outbound port for packets entering port 1.

permDispOutp2

The outbound port for packets entering port 2.

permSrcAddress

The source address in this permanent database entry, i.e. the instance.

specNumEntries

The number of filters in the special database.

specMaxEntries

The maximum number of filters the special database can contain.

specNextFilterNum

The number of the next available filter that can be added to the special database.

specEnable

Enable or disable the filter.

specPort1

Set port 1 to filter or forward packets.

specPort2

Set port 2 to filter or forward packets.

specDestAddress

Set the special database to filter packets with a specific destination address.

specSrcAddress

Set the special database to filter packets with a specific source address.

specType

Set the special database to filter packets with a specific type field.

specDataField

Set the special database to filter packets based on the first sixteen bytes of data in the packet.

specDeleteFilter

Delete a filter from the special database.