ctron-sfps-connection-mib Download
You can select a variable to monitor using the built-in IPHost MIB browser that provides you with all variables, their current values and descriptions taken from the
ctron-sfps-connection-mib
.
OID list for ctron-sfps-connection-mib
- sfpsConnectionTable
- This table contains the connection information for all active connections on the SFPS access ports.
- sfpsConnectionEntry
- Each entry specifies the connection information for the active connection for which the entry exists.
- sfpsConnectionDestination
- The destination SFPS address for this source/destination connection.
- sfpsConnectionSource
- The source SFPS address for this source/destination connection.
- sfpsConnectionPrimInPort
- Identifies the primary inbound SFPS switch port.
- sfpsConnectionPrimOutPort
- Identifies the primary outbound SFPS switch port. All switched traffic for this connection will be transmitted on this outbound port.
- sfpsConnectionSecInPort
- Identifies the secondaryinbound SFPS switch port.
- sfpsConnectionSecOutPort
- Identifies the secondary outbound SFPS switch port. All switched traffic for this connection will be transmitted on this outbound port.
- sfpsConnectionCtrlStatus
- The control state of the SFPS connection.
- sfpsConnectionAdminStatus
- The administrative state of the SFPS connection.
- sfpsConnectionAge
- Indicates the age of the connection.
- sfpsConnectionType
- Sets the type of connection. Provisioned connections are setup manually; switched and vlan connections are setup dynammically.
- sfpsConnectionPkts
- Indicates the total number of packets sent on this connection.
- sfpsConnectionBytes
- Indicates the total number of bytes sent on this connection.
- sfpsConnectionCanAge
- sfpsConnectionPrimOutPorts
- Identifies a list of outbound SFPS switch ports. All switched traffic for this connection will be transmitted on these outbound ports.
- sfpsConnectionSecOutPorts
- Identifies a list of outbound SFPS switch ports. All switched traffic for this connection will be transmitted on these outbound ports.
- sfpsAPIVerb
- Specifies the action to be initiated as a result of setting this leaf.
- sfpsAPIInPort
- Specifies the ingress port of the switch.
- sfpsAPIInHeaderType
- Specfies the type of header being mapped.
- sfpsAPIInHeaderLength
- Specifies the length of the header value.
- sfpsAPIInHeaderValue
- Specifies the actual inHeader value for the mapping.
- sfpsAPIOutPort
- Specifies the egress port of the switch.
- sfpsAPIOutHeaderType
- Specfies the type of header being mapped. This value defaults to the value given to sfpsAPIInHeaderType.
- sfpsAPIOutHeaderLength
- Specifies the length of the header value. This value defaults to the value given to sfpsAPIInHeaderLength.
- sfpsAPIOutHeaderValue
- Specifies the actual outHeader value for the mapping. This value defaults to the value given to sfpsAPIInHeaderValue.
- sfpsAPIArgumentDirection
- Specifies the direction of the connection.
- sfpsAPIArgumentOwner
- Specifies whether or not callcontrol is owned by this agent switch. If the call is owned, then the switch will be responsible for releasing the call. THis is used mainly when transferring call ownership in call re-routing and in setting up originating c ...
- sfpsAPIArgumentPriority
- Specifies the outbound priority of the connection.
- sfpsAPIType
- Sets the type of connection that should be setup.
- sfpsConnectionStatsMaxCnxs
- The maximum number of bi-directional connections allocated for the switch.
- sfpsConnectionStatsTotalCnxs
- The total number of bi-directional connections used in the switch.
- sfpsConnectionStatsSwitchedCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsVlanCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsFilterCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsSelfProgCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsProvsnedCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsTapCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsMcastCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsNetPortFilterCnxs
- The number of bi-directional connections used in the switch with type
- sfpsConnectionStatsNonCriticalVlans
- Number of non-critical connections - these will be aged first
- sfpsConnectionStatsAddErrors
- Number of errors on adding a connnection
- sfpsConnectionStatsDeleteErrors
- Number of errors on deleting a connection
- sfpsConnectionTestAPIVerb
- sfpsConnectionTestAPIType
- sfpsConnectionTestAPINumCnxs
- sfpsConnectionTestAPIMacAddr
- sfpsConnectionTestAPIPort
- sfpsConnectionConfigAPIVerb
- Specifies the verb.
- sfpsConnectionConfigAPICnxHiMark
- Specifies the percentage of the Connection Table needed to be full before beginning aging.
- sfpsConnectionConfigAPICnxNumToAge
- Specifies the number of connections to age at each pass.
- sfpsConnectionConfigAPIAgePeriod
- Specifies the age period. Units in minutes. 0 - No periodic aging N - age every N minutes
- sfpsConnectionConfigAPIAgePassInProgress
- Specifies whether the age pass is in progress. 0 - not aging now 1 - aging now.
- sfpsConnectionConfigAPICurCapacity
- Specifies the percentage of the Connection Table used.
- sfpsConnectionConfigAPILastPassTime
- Specifies the time that the last age pass occured.
- sfpsConnectionConfigAPITimeSinceLastPass
- Specifies the time since the last age pass.
- sfpsConnectionConfigAPIAgePassDelta
- Specifies the time between the last two age passes.
- sfpsConnectionConfigAPIAgePassCount
- Specifies the number of aging passes that have occured.
- sfpsConnectionConfigAPIAgeStatsHiMark
- sfpsConnectionConfigAPIStatsAgingEnable
- sfpsConnectionConfigAPIAgeStatsAgingSupported
- sfpsConnectionConfigAPIIdleCnxs
- sfpsConnectionConfigAPIActiveCnxs
- sfpsConnectionQueryAPIVerb
- Specifies the action to be initiated as a result of setting this leaf.
- sfpsConnectionQueryAPIDestAddr
- Destination MAC address.
- sfpsConnectionQueryAPISourceAddr
- Source MAC address.
- sfpsConnectionQueryAPIInPort
- Source port number.
- sfpsConnectionQueryAPIOutPort
- Destination port number.
- sfpsConnectionQueryAPICtrlStatus
- Control Status
- sfpsConnectionQueryAPIAdminStatus
- Administrative Status.
- sfpsConnectionQueryAPIAge
- Age of connection.
- sfpsConnectionQueryAPIQueryType
- Type of connection.
- sfpsConnectionQueryAPIOwner
- Specifies whether or not Call control is owned by this agent switch. If the call is owned, then the switch will be responsible for releasing the call. This is used mainly when transferring call ownership in call re-routing and in setting up originating ...
- sfpsConnectionQueryAPIPkts
- Number of packets switched on this connection.
- sfpsConnectionQueryAPIBytes
- Number of bytes switched on this connection.
- sfpsConnectionQueryAPICanAge
- Determine if this connection will be aged - (1) means to age.
- sfpsConnectionQueryAPIOutPorts
- If OutPorts is 1 - the multiple outports will be displayed in a text format.
- sfpsConnectionQueryAPIMacAddr
- MAC address.
- sfpsConnectionQueryAPISecInPort
- sfpsConnectionQueryAPISecOutPort
- sfpsConnectionQueryAPISecOutPorts
- sfpsConnectionLookupAPIVerb
- Specifies the action to be initiated as a result of setting this leaf.
- sfpsConnectionLookupAPIMacAddr
- MAC address to be looked up as either the Source or Destination addresses.
- sfpsConnectionLookupAPIDestAddr
- Destination MAC address
- sfpsConnectionLookupAPISourceAddr
- Source MAC address
- sfpsConnectionLookupAPIPrimInPort
- Source port number
- sfpsConnectionLookupAPIPrimOutPort
- Destination port number. If -1, denotes multiple out ports.
- sfpsConnectionLookupAPISecInPort
- Source port number
- sfpsConnectionLookupAPISecOutPort
- Destination port number. If 01, denotes multiple out ports
- sfpsConnectionLookupAPICtrlStatus
- Control status
- sfpsConnectionLookupAPIAdminStatus
- Administrative status
- sfpsConnectionLookupAPIAge
- Age of connection
- sfpsConnectionLookupAPIType
- Type of connection
- sfpsConnectionLookupAPIPkts
- Number of packets switched on this connection
- sfpsConnectionLookupAPIBytes
- Number of bytes switched on this connection
- sfpsConnectionLookupAPICanAge
- Boolean to determine if this connection will be aged. True (1) means to age.
- sfpsConnectionLookupAPIPrimOutPorts
- If Primary OutPort is -1, the multiple outports will be displayed in text format
- sfpsConnectionLookupAPISecOutPorts
- If Secondary OutPort is -1, the multiple outports will be displayed in text format
- sfpsCNXPacketStatsVer1Tx
- Version 1 transmission
- sfpsCNXPacketStatsVer2Tx
- Version 2 transmission
- sfpsCNXPacketStatsVer1Rx
- Version 1 receive
- sfpsCNXPacketStatsVer2Rx
- Version 2 receive
- sfpsCNXPacketStatsOpCode1Tx
- Operation code 1 transmission
- sfpsCNXPacketStatsOpCode2Tx
- Operation code 2 tranmission
- sfpsCNXPacketStatsOpCode1Rx
- Operation code 1 receive
- sfpsCNXPacketStatsOpCode2Rx
- Operation code 2 receive
- sfpsCNXPacketStatsRxErrors
- Receive errors
You can start network devices monitoring using free 30-day trial version of IPHost Network Monitor right now.
Witn IPHost SNMP monitor you can monitor network performance, audit network usage, detect network faults, or inappropriate access.
The IPHost's SNMP monitor can communicate and interact with any SNMP-enabled device.
