dlm-mib Download

snmpPollTable

A list of SNMP poll entries which trigger automatic polling of SNMP requests to other SNMP agents. This table is indexed by the destination IP address of the host/device to be polled and the IP address of the requesting host. This indexing pair allows m ...

snmpPollEntry

An SNMP poll entry containing objects for a particular poll request.

snmpPollDestination

The IP address of the host/device to be polled.

snmpPollOwner

The IP address of the client which created this poll request entry.

snmpPollCommunity

The value of the community string to be used in the SNMP REQUEST PDU when actively polling. Note that this community name string should be defined for the Cabletron hub device as well as in the destination host/device; otherwise polls can fail due to aut ...

snmpPollInterval

The value of the interval (in seconds) on which to poll the destination address with the OIDs defined in the OID table assigned to this poll entry. This interval defines how often an SNMP GET REQUEST PDU will be originated from this host device to the po ...

snmpPollRetry

The value of the number of times to retry a failed poll request prior to considering it a failure.

snmpPollAction

The indication of the action to take when a poll request is considered to have failed. A value of 'no-action' will allow the poll to reset and retry without sending any alarms. A value of 'send-trap' will cause a SNMP TRAP PDU to be generated and sent t ...

snmpPollTrapAddress

The IP address to which to send the SNMP TRAP if the poll is considered a failure and the action is defined as send-trap. The default trap address is the owner address for this entry.

snmpPollType

The administrative control of this poll request entry. This leaf is used to trigure an active request (begin polling), suspend polling (stop polling but leave this poll entry intact) on an active request, or to delete an entry (stop polling and remove en ...

snmpPollStatus

The operational status of this poll request entry. This leaf is used to indicate the state of the last valid poll request.

snmpPollRequests

Indicates the number of poll requests (SNMP GET REQUEST PDUs) have been issued for this poll entry.

snmpPollLastContact

Indicates the value of the sysUpTime when the last poll response was received from the polled host/device for which this poll entry exists.

snmpPollLastAlarm

Indicates the value of the sysUpTime when the last alarm was generated for this poll request entry.

snmpPollAlarmWait

Indicates the number of seconds to wait prior to sending another alarm. This is to ensure that alarms do not flood out upon device contact lost.

snmpPollTrapCommunity

The value of the community string to be used in the SNMP TRAP PDU when a trap is generated.

snmpPollProtocol

Indicates the protocol to use to poll the host/device. If snmp is chosen, there must be at least one corresponding OID Table Entry or a general-failure will result. A corresponding OID Table Entry is an entry with the same Destination and Owner indices.

snmpOIDTable

A list of objects used to define the OBJECT IDENTIFIERS and their attributes (type and threashold values) to be used in a particular snmp poll request SNMP GET REQUEST PDU. These OIDs will make up the VarBindList in the PDU. Only OID types which have IN ...

snmpOIDEntry

An SNMP poll OBJECT IDENTIFIER entry containing objects for a particular OID to be polled.

snmpOIDDestination

The IP address of the host/device to be polled.

snmpOIDOwner

The IP address of the client which created this OID request entry.

snmpOIDSequence

The sequence number which uniquely idenifies this OID entry entry within a particular SNMP poll request. This number is incremented each time an OID as added to the poll list for a particular destination/owner pair.

snmpOIDObject

Identifies the Object Identifier to be polled. This OID value will be placed in a SNMP GET REQUEST PDU on each poll interval.

snmpOIDComparator

Indicates the type of comparison to be performed on the value portion of the OID being polled. This comparator will be used to compare the OID value with the threshold value defined in this entry. A value of 'dont-compare' causes no comparison to be per ...

snmpOIDEnumType

Indicates the type of value to expect from the OID being polled such that the correct interpretation of the threshold value can be used to do the comparison.

snmpOIDThresholdInteger

The threshold value to be used when polling an integer-valued Object Identifier.

snmpOIDThresholdCounter

The threshold value to be used when polling a Counter-type Object Identifier.

snmpOIDThresholdGauge

The threshold value to be used when polling a Gauge-type Object Identifier.

snmpOIDThresholdTicks

The threshold value to be used when polling a TimeTicks-type Object Identifier.

snmpOIDType

The administrative control of this Object Identifier entry. This leaf is used to control adding, using, and deleting OIDs from the OID poll list.

snmpOIDStatus

The status of the last poll of this Object ID.

snmpOIDLastValue

The value of the last poll entry treated as an integer value. This field is used to allow RMON alarms to monitor the polled values.