Cisco Channel Associated Signal Interface Group EM Timing Digit Duration

1.3.6.1.4.1.9.9.85.1.2.2.2.1.7

Outgoing DTMF/MF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpCfgDialType is dtmf or R2 tone. The default value of this object is 100 milliseconds. ::= { ccasGrpEMTmEntry 7 } SYNTAX Integer32 (50..500) UNITS "milliseconds Outgoing DTMF/MF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpCfgDialType is dtmf or R2 tone. The default value of this object is 100 milliseconds. ::= { ccasGrpEMTmEntry 8 } SYNTAX Integer32 (10..20) UNITS "pulses per second Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpCfgDialType is pulse. The default value of this object is 10 pps. ::= { ccasGrpEMTmEntry 9 } SYNTAX Integer32 (100..1000) UNITS "milliseconds Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpCfgDialType is pulse. The default value of this object is 500 milliseconds. ::= { ccasGrpEMTmEntry 10 } SYNTAX Integer32 (0..10000) UNITS "milliseconds The hangover time used to determine there is no more voice packet arrived. The default value of this object is 250 milliseconds. ::= { ccasGrpEMTmEntry 11 } SYNTAX Integer32 (-1 | 5..60000) UNITS "seconds LMR port tear down timeout. This object is relevant to the waiting time of teardown call on LMR port. If the value of this object is '-1', then the timeout is disable. DEFVAL { 1800 } ::= { ccasGrpEMTmEntry 12 } SYNTAX Integer32 (0..30) UNITS "minutes This object signifies LMR port maximum transmit time. This object is relevant to how long LMR port can continue transmit voice packet without pause. DEFVAL { 0 } ::= { ccasGrpEMTmEntry 13 } SYNTAX Integer32 (0..30) UNITS "minutes This object signifies LMR port maximum receive time. This object is relevant to how long LMR port can continue receive voice packet without pause. DEFVAL { 0 } ::= { ccasGrpEMTmEntry 14 } SYNTAX Integer32 (0..1500) UNITS "milliseconds This object is relevant to how long LMR will delay sending the voice packet to the LMR port. DEFVAL { 0 } ::= { ccasGrpEMTmEntry 15 } --********************************************************************* -- The CAS Group FXS/SAS Standard Configuration Table --********************************************************************* SYNTAX SEQUENCE OF CcasGrpLineCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION The CAS Group FXS/SAS Standard Configuration Table. It contains the CAS FXS/SAS group standard configuration information of T1/E1. ::= { ccasGrpLineObjects 1 } SYNTAX CcasGrpLineCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the configuration table for each CAS FXS/SAS Group in the T1/E1. The entry is created when the ccasGrpCfgType is configured as 'fxs' or 'sas' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1. INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasGrpLineCfgTable 1 } CcasGrpLineCfgEntry ::= SEQUENCE { ccasGrpLineCfgNumberRings Integer32, ccasGrpLineCfgSupDisconnect TruthValue, ccasGrpLineCfgDialType INTEGER } SYNTAX Integer32 (0..10) UNITS "rings The number of rings detected before closing loop. If the value of this object is 0, then the managed system answers immediately after the interface detects a incoming seizure if the ccasGrpCfgType is 'fxsGroundStart' or 'sasGroundStart'. The default value of this object is 1 ring. ::= { ccasGrpLineCfgEntry 1 } SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION Specifies whether a supervisory disconnect signal will be presented to the interface when the connected party at the interface hangs up. this object is only relevant to the ccasGrpCfgType is fxsLoopStart or sasLoopStart. The default value of this object is 'true'. ::= { ccasGrpLineCfgEntry 2 } SYNTAX INTEGER { dtmf (1), pulse (2) } MAX-ACCESS read-write STATUS current DESCRIPTION Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. The default value of this object is dtmf(1). ::= { ccasGrpLineCfgEntry 3 } --********************************************************************* -- The FXS/SAS Timing Parameters Table --********************************************************************* -- This table contains the FXS/SAS interface timing parameters -- information. SYNTAX SEQUENCE OF CcasGrpLineTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION The FXS/SAS interface Timing Parameters table. It contains the configuration of the various FXS/SAS signaling protocol timing parameters. ::= { ccasGrpLineObjects 2 } SYNTAX CcasGrpLineTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the FXS/SAS Timing Parameters Table for each FXS/SAS interface.