Cisco Channel Associated Signal Interface Group Line Timing Digit Duration

1.3.6.1.4.1.9.9.85.1.2.3.2.1.1

Outgoing DTMF digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpLineCfgDialType is dtmf. The default value of this object is 100 milliseconds. ::= { ccasGrpLineTmEntry 1 } SYNTAX Integer32 (50..500) UNITS "milliseconds Outgoing DTMF inter-digit duration in milliseconds. This object is not relevant to the addressing timing of the interfaces in the CAS group if ccasGrpLineCfgDialType is dtmf. The default value of this object is 100 milliseconds. ::= { ccasGrpLineTmEntry 2 } SYNTAX Integer32 (10..20) UNITS "pulses per second Outgoing Pulse dialing rate in pulses per second (pps). This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 10 pps. ::= { ccasGrpLineTmEntry 3 } SYNTAX Integer32 (100..1000) UNITS "milliseconds Outgoing Pulse dialing inter-digit timing in milliseconds. This object is relevant to the addressing timing of the interfaces in the CAS group only if ccasGrpStaCfgDialType is pulse. The default value of this object is 500 milliseconds. ::= { ccasGrpLineTmEntry 4 } --********************************************************************* -- The CAS Group FXO/SAO Standard Configuration Table --********************************************************************* -- This table contains the configuration information of FXO/SAO signal -- interface. SYNTAX SEQUENCE OF CcasGrpStaCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION The FXO/SAO standard configuration table. It contains FXO/SAO configuration parameters, one entry per FXO/SAO interface. The configuration information of this table is set by its default setting when the CAS group is created by the configuration commands. ::= { ccasGrpStaObjects 1 } SYNTAX CcasGrpStaCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the standard configuration table for each FXO/SAO Group. The entry is created when the ccasGrpCfgType is configured as 'fxo' or 'sao' on a T1/E1 via configuration command. The entry is deleted when the CAS Group is de-configured from T1/E1. INDEX { ifIndex, ccasGrpCfgIndex } ::= { ccasGrpStaCfgTable 1 } CcasGrpStaCfgEntry ::= SEQUENCE { ccasGrpStaCfgNumberRings Integer32, ccasGrpStaCfgDialType INTEGER } SYNTAX Integer32 (0..1000) UNITS "rings The number of rings sent before sending reorder to the originator and releasing resources. If the value of this object is 0, then sending reorder to the originator is disabled. The default value of this object is 20 rings. ::= { ccasGrpStaCfgEntry 1 } SYNTAX INTEGER { dtmf (1), pulse (2) } MAX-ACCESS read-write STATUS current DESCRIPTION Specify the addressing type of the CAS group. dtmf - Dual Tone Multi-Frequency (DTMF) digit. pulse - dial pulse. The default value of this object is dtmf(1). ::= { ccasGrpStaCfgEntry 2 } --********************************************************************* -- The FXO/SAO Timing Parameters Table --********************************************************************* -- This table contains the FXO/SAO interface timing parameters -- information. SYNTAX SEQUENCE OF CcasGrpStaTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION The FXO/SAO interface Timing Parameters table. It contains the configuration of the various FXO/SAO signaling protocol timing parameters. ::= { ccasGrpStaObjects 2 } SYNTAX CcasGrpStaTmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the FXO/SAO Timing Parameters Table for each FXO/SAO interface.