ADSL-LINE-MIB

ADSL-LINE-MIB Download

MIBs list

The MIB module defining objects for the management of a pair of ADSL modems at each end of the ADSL line. Each such line has an entry in an ifTable which may include multiple modem lines. An agent may reside at either end of the ADSL line however the MIB is designed to require no management communication between them beyond that inherent in the low-level ADSL line protocol. The agent may monitor and control this protocol for its needs.

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for ADSL-LINE-MIB

adslLineTable
This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslLineEntry
An entry in adslLineTable.
adslLineCoding
Specifies the ADSL coding type used on this line. Other types may be added in the future.
adslLineType
Defines the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. In the case t ...
adslLineSpecific
OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM.
adslLineConfProfile
The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the configuration profile has not bee ...
adslLineAlarmConfProfile
The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. For `dynamic' mode, in the case which the alarm profile has not b ...
adslAtucPhysTable
This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAtucPhysEntry
An entry in the adslAtucPhysTable.
adslAtucInvSerialNumber
Vendor specific string that identifies the vendor equipment.
adslAtucInvVendorID
The vendor ID assigned by T1E1.413 according to its Annex D.[10]
adslAtucInvVersionNumber
Vendor specific version number sent by this ATU as part of the initialization messages.
adslAtucCurrSnrMgn
Noise Margin as seen by this ATU with respect to its received signal in tenth dB.
adslAtucCurrAtn
Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. This value is determined in accordance with T1.413[10].
adslAtucCurrStatus
Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 ...
adslAtucCurrOutputPwr
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
adslAtucCurrAttainableRate
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
adslAturPhysTable
This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAturPhysEntry
An entry in the adslAturPhysTable.
adslAturInvSerialNumber
Vendor specific string that identifies the vendor equipment.
adslAturInvVendorID
The vendor ID assigned by T1E1.413 according to its Annex D.
adslAturInvVersionNumber
Vendor specific version number sent by this ATU as part of the initialization messages.
adslAturCurrSnrMgn
Noise Margin as seen by this ATU with respect to its received signal. This value is determined in accordance with T1.413 [10].
adslAturCurrAtn
Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. This value is determined in accordance with T1.413[10].
adslAturCurrStatus
Indicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be deter ...
adslAturCurrOutputPwr
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
adslAturCurrAttainableRate
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
adslAtucChanTable
This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAtucChanEntry
An entry in the adslAtucChanTable.
adslAtucChanInterleaveDelay
Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. ...
adslAtucChanCurrTxRate
Actual transmit rate on this channel.
adslAtucChanPrevTxRate
The rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object ...
adslAtucChanCrcBlockLength
Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.
adslAturChanTable
This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAturChanEntry
An entry in the adslAturChanTable.
adslAturChanInterleaveDelay
Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. ...
adslAturChanCurrTxRate
Actual transmit rate on this channel.
adslAturChanPrevTxRate
The rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object ...
adslAturChanCrcBlockLength
Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.
adslAtucPerfDataTable
This table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAtucPerfDataEntry
An entry in adslAtucPerfDataTable.
adslAtucPerfLofs
Count of the number of Loss of Framing failures since agent reset.
adslAtucPerfLoss
Count of the number of Loss of Signal failures since agent reset.
adslAtucPerfLols
Count of the number of Loss of Link failures since agent reset.
adslAtucPerfLprs
Count of the number of Loss of Power failures since agent reset.
adslAtucPerfESs
Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAtucPerfInits
Count of the line initialization attempts since agent reset. Includes both successful and failed attempts.
adslAtucPerfValidIntervals
Number of previous 15-minute intervals in the adslAtucInterval Table for which valid data has been stored. This value will be equal to the maximum # of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the ...
adslAtucPerfInvalidIntervals
The number of 15 minute intervals in which no valid data is available.
adslAtucPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval. A full interval is 900 seconds.
adslAtucPerfCurr15MinLofs
Count of seconds in the current 15 minute interval when there was Loss of Framing.
adslAtucPerfCurr15MinLoss
Count of seconds in the current 15 minute interval when there was Loss of Signal.
adslAtucPerfCurr15MinLols
Count of seconds in the current 15 minute interval when there was Loss of Link.
adslAtucPerfCurr15MinLprs
Count of seconds in the current 15 minute interval when there was Loss of Power.
adslAtucPerfCurr15MinESs
Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAtucPerfCurr15MinInits
Count of the line initialization attempts in the current 15 minute interval. Includes both successful and failed attempts.
adslAtucPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the beginning of the current 1-day interval.
adslAtucPerfCurr1DayLofs
Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
adslAtucPerfCurr1DayLoss
Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
adslAtucPerfCurr1DayLols
Count of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
adslAtucPerfCurr1DayLprs
Count of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
adslAtucPerfCurr1DayESs
Count of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAtucPerfCurr1DayInits
Count of the line initialization attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed. Includes both successful and failed attempts.
adslAtucPerfPrev1DayMoniSecs
The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring data can not be collected ...
adslAtucPerfPrev1DayLofs
Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.
adslAtucPerfPrev1DayLoss
Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.
adslAtucPerfPrev1DayLols
Count of seconds in the interval when there was Loss of Link within the most recent previous 1-day period.
adslAtucPerfPrev1DayLprs
Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.
adslAtucPerfPrev1DayESs
Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAtucPerfPrev1DayInits
Count of the line initialization attempts in the most recent previous 1-day period. Includes both successful and failed attempts.
adslAturPerfDataTable
This table provides one row for each ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAturPerfDataEntry
An entry in adslAturPerfDataTable.
adslAturPerfLofs
Count of the number of Loss of Framing failures since agent reset.
adslAturPerfLoss
Count of the number of Loss of Signal failures since agent reset.
adslAturPerfLprs
Count of the number of Loss of Power failures since agent reset.
adslAturPerfESs
Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAturPerfValidIntervals
Number of previous 15-minute intervals in the adslAturInterval Table for which valid data has been stored. This value will be equal to the maximum # of intervals that are kept (n) unless the device was brought online within the last (nx15) min. In the cas ...
adslAturPerfInvalidIntervals
The number of 15 minute intervals in which no valid data is available.
adslAturPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval. A full interval is 900 seconds.
adslAturPerfCurr15MinLofs
Count of seconds in the current 15 minute interval when there was Loss of Framing.
adslAturPerfCurr15MinLoss
Count of seconds in the current 15 minute interval when there was Loss of Signal.
adslAturPerfCurr15MinLprs
Count of seconds in the current 15 minute interval when there was Loss of Power.
adslAturPerfCurr15MinESs
Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAturPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the beginning of the current 1-day interval.
adslAturPerfCurr1DayLofs
Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
adslAturPerfCurr1DayLoss
Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
adslAturPerfCurr1DayLprs
Count of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
adslAturPerfCurr1DayESs
Count of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAturPerfPrev1DayMoniSecs
The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring data can not be collected ...
adslAturPerfPrev1DayLofs
Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.
adslAturPerfPrev1DayLoss
Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.
adslAturPerfPrev1DayLprs
Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.
adslAturPerfPrev1DayESs
Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAtucIntervalTable
This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAtucIntervalEntry
An entry in the adslAtucIntervalTable.
adslAtucIntervalNumber
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
adslAtucIntervalLofs
Count of seconds in the interval when there was Loss of Framing.
adslAtucIntervalLoss
Count of seconds in the interval when there was Loss of Signal.
adslAtucIntervalLols
Count of seconds in the interval when there was Loss of Link.
adslAtucIntervalLprs
Count of seconds in the interval when there was Loss of Power.
adslAtucIntervalESs
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAtucIntervalInits
Count of the line initialization attempts during the interval. Includes both successful and failed attempts.
adslAtucIntervalValidData
This object indicates if there is valid data for this interval.
adslAturIntervalTable
This table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
adslAturIntervalEntry
An entry in the adslAturIntervalTable.
adslAturIntervalNumber
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
adslAturIntervalLofs
Count of seconds in the interval when there was Loss of Framing.
adslAturIntervalLoss
Count of seconds in the interval when there was Loss of Signal.
adslAturIntervalLprs
Count of seconds in the interval when there was Loss of Power.
adslAturIntervalESs
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
adslAturIntervalValidData
This object indicates if there is valid data for this interval.
adslAtucChanPerfDataTable
This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAtucChanPerfDataEntry
An entry in adslAtucChanPerfDataTable.
adslAtucChanReceivedBlks
Count of all encoded blocks received on this channel since agent reset.
adslAtucChanTransmittedBlks
Count of all encoded blocks transmitted on this channel since agent reset.
adslAtucChanCorrectedBlks
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
adslAtucChanUncorrectBlks
Count of all blocks received with uncorrectable errors since agent reset.
adslAtucChanPerfValidIntervals
Number of previous 15-minute intervals in the adslAtucChanIntervalTable Table for which valid data has been stored. This value will be equal to the max number of intervals that are kept (n) unless the device was brought online within the last (nx15) minut ...
adslAtucChanPerfInvalidIntervals
The number of 15 minute intervals in which no valid data is available.
adslAtucChanPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval. A full interval is 900 seconds.
adslAtucChanPerfCurr15MinReceivedBlks
Count of all encoded blocks received on this channel within the current 15 minute interval.
adslAtucChanPerfCurr15MinTransmittedBlks
Count of all encoded blocks transmitted on this channel within the current 15 minute interval.
adslAtucChanPerfCurr15MinCorrectedBlks
Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval.
adslAtucChanPerfCurr15MinUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.
adslAtucChanPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the beginning of the current 1-day interval.
adslAtucChanPerfCurr1DayReceivedBlks
Count of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
adslAtucChanPerfCurr1DayTransmittedBlks
Count of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
adslAtucChanPerfCurr1DayCorrectedBlks
Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
adslAtucChanPerfCurr1DayUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
adslAtucChanPerfPrev1DayMoniSecs
The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be co ...
adslAtucChanPerfPrev1DayReceivedBlks
Count of all encoded blocks received on this channel within the most recent previous 1-day period.
adslAtucChanPerfPrev1DayTransmittedBlks
Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period.
adslAtucChanPerfPrev1DayCorrectedBlks
Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.
adslAtucChanPerfPrev1DayUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.
adslAturChanPerfDataTable
This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAturChanPerfDataEntry
An entry in adslAturChanPerfDataTable.
adslAturChanReceivedBlks
Count of all encoded blocks received on this channel since agent reset.
adslAturChanTransmittedBlks
Count of all encoded blocks transmitted on this channel since agent reset.
adslAturChanCorrectedBlks
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
adslAturChanUncorrectBlks
Count of all blocks received with uncorrectable errors since agent reset.
adslAturChanPerfValidIntervals
Number of previous 15-minute intervals in the adslAturChanIntervalTable Table for which valid data has been stored. This value will be equal to the max # of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. ...
adslAturChanPerfInvalidIntervals
The number of 15 minute intervals in which no valid data is available.
adslAturChanPerfCurr15MinTimeElapsed
Total elapsed seconds in this interval. A full interval is 900 seconds.
adslAturChanPerfCurr15MinReceivedBlks
Count of all encoded blocks received on this channel within the current 15 minute interval.
adslAturChanPerfCurr15MinTransmittedBlks
Count of all encoded blocks transmitted on this channel within the current 15 minute interval.
adslAturChanPerfCurr15MinCorrectedBlks
Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval.
adslAturChanPerfCurr15MinUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.
adslAturChanPerfCurr1DayTimeElapsed
Number of seconds that have elapsed since the beginning of the current 1-day interval.
adslAturChanPerfCurr1DayReceivedBlks
Count of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
adslAturChanPerfCurr1DayTransmittedBlks
Count of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
adslAturChanPerfCurr1DayCorrectedBlks
Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
adslAturChanPerfCurr1DayUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
adslAturChanPerfPrev1DayMoniSecs
The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be co ...
adslAturChanPerfPrev1DayReceivedBlks
Count of all encoded blocks received on this channel within the most recent previous 1-day period.
adslAturChanPerfPrev1DayTransmittedBlks
Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period.
adslAturChanPerfPrev1DayCorrectedBlks
Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.
adslAturChanPerfPrev1DayUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.
adslAtucChanIntervalTable
This table provides one row for each ATUC channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAtucChanIntervalEntry
An entry in the adslAtucIntervalTable.
adslAtucChanIntervalNumber
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
adslAtucChanIntervalReceivedBlks
Count of all encoded blocks received on this channel during this interval.
adslAtucChanIntervalTransmittedBlks
Count of all encoded blocks transmitted on this channel during this interval.
adslAtucChanIntervalCorrectedBlks
Count of all blocks received with errors that were corrected on this channel during this interval.
adslAtucChanIntervalUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel during this interval.
adslAtucChanIntervalValidData
This object indicates if there is valid data for this interval.
adslAturChanIntervalTable
This table provides one row for each ATUR channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125).
adslAturChanIntervalEntry
An entry in the adslAturIntervalTable.
adslAturChanIntervalNumber
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
adslAturChanIntervalReceivedBlks
Count of all encoded blocks received on this channel during this interval.
adslAturChanIntervalTransmittedBlks
Count of all encoded blocks transmitted on this channel during this interval.
adslAturChanIntervalCorrectedBlks
Count of all blocks received with errors that were corrected on this channel during this interval.
adslAturChanIntervalUncorrectBlks
Count of all blocks received with uncorrectable errors on this channel during this interval.
adslAturChanIntervalValidData
This object indicates if there is valid data for this interval.
adslLineConfProfileTable
This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line.
adslLineConfProfileEntry
Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a profile is created in one step with all necessary parameter values and adslLineProfileRowStatus set to createAndGo. ...
adslAtucConfRateMode
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.
adslAtucConfRateChanRatio
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: ads ...
adslAtucConfTargetSnrMgn
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
adslAtucConfMaxSnrMgn
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
adslAtucConfMinSnrMgn
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
adslAtucConfDownshiftSnrMgn
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL is not present, the value will be `0'.
adslAtucConfUpshiftSnrMgn
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
adslAtucConfMinUpshiftTime
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.
adslAtucConfMinDownshiftTime
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, the value will be `0'.
adslAtucChanConfFastMinTxRate
Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates.
adslAtucChanConfInterleaveMinTxRate
Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates.
adslAtucChanConfFastMaxTxRate
Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates.
adslAtucChanConfInterleaveMaxTxRate
Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates.
adslAtucChanConfMaxInterleaveDelay
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the i ...
adslAturConfRateMode
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.
adslAturConfRateChanRatio
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: ads ...
adslAturConfTargetSnrMgn
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
adslAturConfMaxSnrMgn
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
adslAturConfMinSnrMgn
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
adslAturConfDownshiftSnrMgn
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL is not present, the value will be `0'.
adslAturConfUpshiftSnrMgn
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
adslAturConfMinUpshiftTime
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.
adslAturConfMinDownshiftTime
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, the value will be `0'.
adslAturChanConfFastMinTxRate
Configured Minimum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates.
adslAturChanConfInterleaveMinTxRate
Configured Minimum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates.
adslAturChanConfFastMaxTxRate
Configured Maximum Transmit rate for `Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates.
adslAturChanConfInterleaveMaxTxRate
Configured Maximum Transmit rate for `Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates.
adslAturChanConfMaxInterleaveDelay
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the i ...
adslLineConfProfileRowStatus
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of ...
adslLineAlarmConfProfileTable
This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line
adslLineAlarmConfProfileEntry
Each entry consists of a list of parameters that represents the configuration of an ADSL modem. When `dynamic' profiles are implemented, a profile is created in one step with all necessary parameter values and adslLineProfileRowStatus set to createAndGo. ...
adslAtucThresh15MinLofs
The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. Limit of one trap will be sent for any one interval. A ...
adslAtucThresh15MinLoss
The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. Limit of one trap will be sent for any one interval. A ...
adslAtucThresh15MinLols
The number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. Limit of one trap will be sent for any one interval. A ...
adslAtucThresh15MinLprs
The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. Limit of one trap will be sent for any one interval. A ...
adslAtucThresh15MinESs
The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. Limit of one trap will be sent for any one interval. A value o ...
adslAtucThreshFastRateUp
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. Set to `0' to disable.
adslAtucThreshInterleaveRateUp
Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. Set to `0' to disable.
adslAtucThreshFastRateDown
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. Set to `0' to disable.
adslAtucThreshInterleaveRateDown
Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. Set to `0' to disable.
adslAtucInitFailureTrapEnable
Enables and disables the InitFailureTrap. This object is defaulted disable(2).
adslAturThresh15MinLofs
The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. Limit of one trap will be sent for any one interval. A ...
adslAturThresh15MinLoss
The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. Limit of one trap will be sent for any one interval. A ...
adslAturThresh15MinLprs
The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. Limit of one trap will be sent for any one interval. A ...
adslAturThresh15MinESs
The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. Limit of one trap will be sent for any one interval. A value o ...
adslAturThreshFastRateUp
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. Set to `0' to disable.
adslAturThreshInterleaveRateUp
Applies to `Interleave' channels only. configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. Set to `0' to disable.
adslAturThreshFastRateDown
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. Set to `0' to disable.
adslAturThreshInterleaveRateDown
Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. Set to `0' to disable.
adslLineAlarmConfProfileRowStatus
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of ...
adslLineGroup
A collection of objects providing configuration information about an ADSL Line.
adslPhysicalGroup
A collection of objects providing physical configuration information of the ADSL Line.
adslChannelGroup
A collection of objects providing configuration information about an ADSL channel.
adslAtucPhysPerfRawCounterGroup
A collection of objects providing raw performance counts on an ADSL Line (ATU-C end).
adslAtucPhysPerfIntervalGroup
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) .
adslAturPhysPerfRawCounterGroup
A collection of objects providing raw performance counts on an ADSL Line (ATU-R end).
adslAturPhysPerfIntervalGroup
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end).
adslAtucChanPerformanceGroup
A collection of objects providing channel block performance information on an ADSL channel (ATU-C end).
adslAturChanPerformanceGroup
A collection of objects providing channel block performance information on an ADSL channel (ATU-C end).
adslLineProfileGroup
A collection of objects providing provisioning information about an ADSL Line.
adslLineAlarmConfProfileGroup
A collection of objects providing alarm provisioning information about an ADSL Line.
adslLineProfileControlGroup
A collection of objects providing profile control for the ADSL system.
adslAturLineGroup
A collection of objects providing configuration information about an ADSL Line on the ATU-R side.
adslAturPhysicalGroup
A collection of objects providing physical configuration information of the ADSL Line on the ATU-R side.
adslAturChannelGroup
A collection of objects providing configuration information about an ADSL channel on the ATU-R side.
adslAturAtucPhysPerfRawCounterGroup
A collection of objects providing raw performance counts on an ADSL Line (ATU-C end) provided by the ATU-R agent.
adslAturAtucPhysPerfIntervalGroup
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) provided by the ATU-R agent.
adslAturAturPhysPerfRawCounterGroup
A collection of objects providing raw performance counts on an ADSL Line (ATU-R end) provided by the ATU-R agent.
adslAturAturPhysPerfIntervalGroup
A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end) provided by the ATU-R agent.
adslAturAtucChanPerformanceGroup
A collection of objects providing channel block performance information on an ADSL channel (ATU-C end) provided by the ATU-R agent.
adslAturAturChanPerformanceGroup
A collection of objects providing channel block performance information on an ADSL channel (ATU-R end) provided by the ATU-R agent.
adslAturLineProfileGroup
A collection of objects providing provisioning information about an ADSL Line by the ATU-R agent.
adslAturLineAlarmConfProfileGroup
A collection of objects providing alarm provisioning information about an ADSL Line provided by the ATU-R agent.
adslAturLineProfileControlGroup
A collection of objects providing profile control for the ADSL system by the ATU-R agent.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list