ADTRAN-DSUDPP-MIB Download
The ADTRAN DSUDP Plus MIB
IPHost Network Monitor offer an easy way of SNMP monitoring your ADTRAN Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for ADTRAN-DSUDPP-MIB
- adDSUDPnetLoopRate
- Indicates the DS0 loop data rate
- adDSUDPnetType
- Selects the network type
- adDSUDPnetScrambler
- Disables/Enables Scrambling
- adDSUDPnetRemoteCfg
- Enables/Disables configuration by a remote DSUDP
- adDSUDPdteRate
- Selects bit rate of primary DTE
- adDSUDPdteFormat
- Selects DTE data format
- adDSUDPdteWordLength
- Selects DTE asynchronous word length
- adDSUDPdteInBandCommand
- Selects DTE in-band command type
- adDSUDPdteTxClock
- Selects transmit timing source
- adDSUDPdteCSOptions
- Configures CS signal lead on primary DTE
- adDSUDPdteAntiStream
- Configures DTE Anti-Streaming Disconnect
- adDSUDPdteCDOptions
- Configures CD signal lead on primary DTE
- adDSUDPdteTROptions
- Configures handling of TR lead from Primary DTE
- adDSUDPdteSROptions
- Configures SR signal lead to primary DTE
- adDSUDPdteRSCSDelay
- Configures DTE signals RS-CS delay
- adDSUDPtestTimeout
- Configures test timeout in seconds
- adDSUDPtestRdlCfg
- Enables/Disables response to Remote Digital Loopback
- adDSUDPDialStored1
- Edit or View stored Dial Location 1
- adDSUDPDialStored2
- Edit or View stored Dial Location 2
- adDSUDPDialStored3
- Edit or View stored Dial Location 3
- adDSUDPDialStored4
- Edit or View stored Dial Location 4
- adDSUDPDialStored5
- Edit or View stored Dial Location 5
- adDSUDPDialStored6
- Edit or View stored Dial Location 6
- adDSUDPDialStored7
- Edit or View stored Dial Location 7
- adDSUDPDialStored8
- Edit or View stored Dial Location 8
- adDSUDPDialStored9
- Edit or View stored Dial Location 9
- adDSUDPDialStored10
- Edit or View stored Dial Location 10
- adDSUDPAutoAnswer
- Enables/Disables automatic answer of incoming calls
- adDSUDPTestCmd
- A SET performs the selected test
- adDSUDPTestStatus
- Current test status
- adDSUDPTestErrors
- This variable accumulates errors for the active test pattern. A SET operation will clear the error count.
- adDSUDPTestRxPattern
- Receive test pattern status
- adDSUDPSelfDiagnostics
- Current Self Test status
- adDSUDPTestTxPattern
- SETs default transmit test pattern
- adDSUDPInjectError
- SET injects one error into active test pattern
- adDSUDPStatusEIA
- Bit map status of Primay DTE EIA interface signals (off = 0, on = 1), where bit positions are: 1 RI 2 RD 4 SD 8 CD 16 CS 32 RS 64 SR 128 TR
- adDSUDPStatusConnector
- The jumper selected DTE interface connector on DSUDP
- adDSUDPMode
- Current mode of DSUDP
- adDSUDPLedStatus
- This variable contains bit encoded values for LED status (0=off, 1=on): 1 IDL 2 ALM 4 TST 8 ERR
- adDSUDPDialStored
- Dials the stored number in register 1-10
- adDSUDPManualDial
- A SET dials the input command string
- adDSUDPAnswerCall
- A SET answers an incoming call
- adDSUDPHangUp
- A SET commands the DSUDP to go on-hook
- adDSUDPds0IntervalTable
- The DS0 Interval Table.
- adDSUDPds0IntervalEntry
- An entry in the DS0 Interval Table.
- adDSUDPds0IntervalIndex
- The index value which uniquely identifies the DS0 interface to which this entry is applicable.
- adDSUDPds0IntervalNumber
- A number between 1 and 97, where 1 is the current accumulating 15 minute interval and 2-97 are completed 15 minute intervals. 2 is the most recent completed interval and 97 is the least recent completed 15 minute interval (assuming that all 97 interval ...
- adDSUDPds0IntervalUASs
- The number of Unavailable Seconds encountered by a DS0 interface in one of the 97, individual 15 minute, intervals.
- adDSUDPds0DailyTable
- The DS0 Daily table.
- adDSUDPds0DailyEntry
- An entry in the DS0 Daily table.
- adDSUDPds0DailyIndex
- The index value which uniquely identifies the DS0 interface to which this entry is applicable.
- adDSUDPds0DailyNumber
- A number between 1 and 7, where 1 is the current accumulating Daily Interval and 2-7 are the completed Daily Intervals. 2 is the most recent completed Daily Interval and 7 is the least recent completed Daily Interval (assuming that all 7 Daily Intervals ...
- adDSUDPds0DailyUASs
- The number of Unavailable Seconds encountered by a DS0 interface in one of the 7 Daily Intervals.
- adDSUDPds0DailyAvail
- The percentage (times 100) of channel availability encountered by a DS0 interface in one of the 7 Daily Intervals.
- adDSUDPds0DailyAvgAvail
- The percentage (times 100) of channel availability averaged over the last 7 days
- adDSUDPds0IntervalThrsTable
- The DS0 Interval Threshold Table.
- adDSUDPds0IntervalThrsEntry
- An entry in the DS0 Threshold Table.
- adDSUDPds0IntervalThrsIndex
- The index value which uniquely identifies the DS0 interface to which this entry is applicable.
- adDSUDPds0IntervalThrsUASs
- The DS0 performance monitor Threshold Value for the 15 minute Unavailable Seconds parameter. The default value is 1, which equates to approximately 99.9% Availability for a 15 minute Interval.
- adDSUDPds0DailyThrsTable
- The DS0 Daily Threshold Table.
- adDSUDPds0DailyThrsEntry
- An entry in the DS0 Threshold Table.
- adDSUDPds0DailyThrsIndex
- The index value which uniquely identifies the DS0 interface to which this entry is applicable.
- adDSUDPds0DailyThrsUASs
- The DS0 performance monitor Threshold Value for the Daily Unavailable Seconds parameter. The default value is 86, which equates to approximately 99.9% Availability for a Daily Interval.
- adDSUDPds0DailyThrsAvail
- The DS0 performance monitor Threshold Value for the percentage channel Availability parameter. The default value is 9950 (% times 100), which equates to 99.5% Availability for a Daily Interval.
- adDSUDPds0AlertTable
- The DS0 Performance Monitor Alert Table
- adDSUDPds0AlertEntry
- An entry in the DS0 PM Alert Table
- adDSUDPds0AlertIndex
- The index value which uniquely identifies the DS0 PM interface to which this entry is applicable.
- adDSUDPds0AlertStatus
- This bit map variable indicates Threshold Crossing Events for DS0 performance monitored parameters. When a parameter exceeds its threshold value, the parameter's bit is set in this variable. A SNMP trap is generated if the parameter's alert enable bit i ...
- adDSUDPds0AlertEnable
- This bit map variable enables changes in the DS0 PM Alert Status to generate a SNMP Trap. The alert enable bit values are: 1 Interval UAS 2 Daily UAS 4 Daily percent Availability
- adDSUDPAlarmStatus
- This bit map variable indicates changes in the DSUDP status. When a status bit changes state, the the corresponding bit is set in this variable. The alarm event bit values are: 1 No Alarm 2 0 4 0 8 Self diagnostics failed 16 OOS/OOF from network ...
- adDSUDPAlarmMajor
- A bit mask to select items of the AlarmStatus which represent a Major Alarm
- adDSUDPAlarmMinor
- A bit mask to select items of the AlarmStatus which represent a Minor Alarm
- adDSUDPAlarmAlert
- A bit mask to select items of the AlarmStatus which represent an Alert Alarm
- adDSUDPAlarmInfo
- A bit mask to select items of the AlarmStatus which represent an Info Alarm
- adDSUDPAlarmEnable
- This bit map variable enables changes in the DSUDP Alarm Status to generate a SNMP Trap. The alarm enable bit values are: 1 0 2 0 4 0 8 Self diagnostics failed 16 OOS/OOF from network 32 DSUDP Loopback 64 Channel Loopback 128 OCU Loopback
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
