ADTRAN-DSUIQ-MIB Download

adDSUIQPassword

Sets the Telnet and Vt100 Terminal Control Password (10 characters maximum).

adDSUIQTOD

Sets the Time of Day with the format hh:mm.

adDSUIQDate

Sets the Date with format MM-DD-YY.

adDSUIQIpAddress

Sets the unit's IP Address.

adDSUIQIpAddressMask

Sets the unit's Subnet Mask.

adDSUIQGatewayIpAddress

Sets the Network's Gateway IP Address.

adDSUIQTrapManagerIpAddress

Sets the IP Address of the Trap Host Manager.

adDSUIQTrapManagerDLCI

Sets the DLCI of the Trap Host Manager. (Range 16 - 1007).

adDSUIQTrapManagerPort

Selects the Trap Manager Port.

adDSUIQControPortBaud

Selects the Control Port baud rate.

adDSUIQControPortMode

Selects the Control Port protocol.

adDSUIQEnableTraps

Overall trap enable/disable.

adDSUIQAlarmState

This bit map variable indicates alarm conditions which are currently set. When an alarm condition occurs, the corresponding event bit is set in this variable. If armed, setting the event will generate an Alarm Trap. The various alarm event bit positions ...

adDSUIQArmAlarm

This bit map variable arms or disarms an individual or group of events identified in adFradAlarmState as a source for generation of an Alarm Trap. The various arm event bit positions are : 1 = Network physical link up. 2 = Network physical link down. 4 = ...

adDSUIQAbortConfig

A Set will cancel the current selections and revert to the last Saved configuration.

adDSUIQSaveConfig

A Set operation will reset the unit and save current selections.

adDSUIQNetPortLoopRate

Selects the Rate for the DDS interface.

adDSUIQNetPortClockSource

Selects the Timing source for the DDS interface.

adDSUIQNetPortSignaling

Signaling type for the frame relay management interface.

adDSUIQNetPortt391

Sets the polling interval in seconds for the frame relay management interface. (Range 5 - 30).

adDSUIQNetPortn391

Sets the interval between full status polls for the frame relay management interface. (Range 1 - 255).

adDSUIQNetPortn392

Sets the error count for the frame relay management interface. (Range 1 - 10).

adDSUIQNetPortn393

Sets the error window (number of polling events)for the frame relay management interface. (Range 1 - 10).

adDSUIQNetPortMgmtDlci1Mode

Sets the mode for the managent DLCI 1. If set for shared, management DLCI 1 is used for customer data and IQ management data. If set for dedicated, management DLCI 1 is used only for IQ management data and is not passed to the attached frame relay DTE ...

adDSUIQNetPortMgmtDlci2Mode

Sets the mode for the managent DLCI 2. If set for shared, management DLCI 2 is used for customer data and IQ management data. If set for dedicated, management DLCI 2 is used only for IQ management data and is not passed to the attached frame relay DTE ...

adDSUIQNetMgmtDlci1

Sets the DLCI for management PVC 1. (Range 16 - 1007).

adDSUIQNetMgmtDlci2

Sets the DLCI for management PVC 2. (Range 16 - 1007).

adDSUIQNetPortMaxPVCs

Sets the maxium PVCs supported by the IQ unit. (Range 1 - 100).

adDSUIQNetPortHistIntervals

Sets the number of history intervals for storage.

adDSUIQNetPortHistIntervalsAvailable

Returns the number of history intervals allowed based on the maxium number of PVCs selected.

adDSUIQDtePortInterface

Selects the DTE Port Interface type.

adDSUIQDtePortRate

Selects the DTE Port Rate.

adDSUIQDteCTSOption

Selects the Clear to Send (CTS) option.

adDSUIQDteCDOption

Selects the Carrier Detect (CD) option.

adDSUIQDteDSROption

Selects the Data Set Ready (DSR) option.

adDSUIQDtePortMgmtDLCI

Sets the DTE Port Management DLCI. (Range 16 - 1007).

adDSUIQDtePortt392

Sets the timeout in seconds between polling intervals. (Range 5 - 30).

adDSUIQDtePortn392

Sets the number of error events for the frame relay management. (Range 1 - 10).

adDSUIQDtePortn393

Sets the error window (polling events) for the frame relay management (Range 1 - 10).

adDSUIQDteManagementPvcOption

Controls the presence of the DTE management PVC in a full status response to the DTE device.

adDSUIQDteSignalingResponsesOption

Determines how the IQ device will respond to polls from the DTE device during a network failure. If set to always on, the IQ will respond to polls during a network failure. If set to follow network, the IQ will not respond thus emulating a failure to the ...

adDSUIQDteFlowControlOption

Determines how the IQ device will respond to congestion during DBU operation. If set for none, the IQ will drop frames during DBU operation when severe congestion occurs. If set for hardware, the IQ will vary the DTE TC clock in order to control the amoun ...

adDSUIQPvcConfigTable

n/a.

adDSUIQPvcConfigEntry

n/a

adDSUIQPvcConfigIndex

n/a.

adDSUIQPvcDLCI

Address for this PVC entry. (Range 16 - 1007).

adDSUIQPvcCIR

Commited Information Rate for this PVC in Kbps.

adDSUIQPvcSequenceOption

Sequence number allows the IQ to detect lost frames across the frame relay service. This option should be disabled for PVCs that do not have IQ on both ends.

adDSUIQPvcDelayPacketOption

Delay packet option for this PVC allows the IQ to sample round trip delay across the frame relay service. This option should be disabled for PVCs that do not have IQ on both ends.

adDSUIQPvcDBUDLCI

Used when this PVC entry is used for dial backup. This value should contain the PVC address as seen on the far end of the PVC.

adDSUIQPvcStatsControl

Stats Control option determines how the IQ will track statistics for this PVC entry. Auto will allow the IQ to track statistics for a PVC if enough memory is available.

adDSUIQDDSState

Current status of the DDS interface

adDSUIQDteControlLeads

This bit map integer reflects the current state of the DTE control leads as follows: bit meaning 0 CTS 1 RTS 2 DSR 3 DTR 4 DCD A 1 means the lead is on.

adDSUIQDBUPortType

Returns the DBU card type installed.

adDSUIQLANPortStatus

Returns the LAN card type installed.

adDSUIQLEDstatus

This bit map integer reflects DSUIQ front panel LED state as follows: bit meaning 0 TEST 1 ALARM 2 DCD 3 RD 4 TD 5 CTS 6 RTS ::= { adDSUIQCurrentStatus 5 } SYNTAX INTEGER { up(1), down(2) } ACCESS read-only STATUS mandatory DESCRIPT ...

adDSUIQNETSignalingState

Current state of the PVC signaling between the DSUIQ and the frame relay service.

adDSUIQNETPVCCount

Current count of network pvcs.

adDSUIQNETPVCConfigTableSize

Current count of rows in the PVC config table.

adDSUIQDBUState

Current state of the DBU interface.

adDSUIQIntDDSStatusTable

n/a.

adDSUIQIntDDSStatusEntry

n/a

adDSUIQIntDDSSlotIndex

n/a.

adDSUIQIntDDSUnavailableTime

Amount of time in seconds the DDS port is unavailable due to test or in an inactive state.

adDSUIQIntDDSStateChange

Number of changes in the DDS port state. This includes all normal, inactive, and test state transitions.

adDSUIQIntDDSBPVFrameError

Number of BPVs received when the DDS is set for 56K mode or the number of DDS framing errors when the DDS is set for 64K mode.

adDSUIQDayDDSStatusTable

n/a.

adDSUIQDayDDSStatusEntry

n/a

adDSUIQDayDDSSlotIndex

n/a.

adDSUIQDayDDSUnavailableTime

Amount of time in seconds the DDS port is unavailable due to test or in an inactive state.

adDSUIQDayDDSStateChange

Number of changes in the DDS port state. This includes all normal, inactive, and test state transitions.

adDSUIQDayDDSBPVFrameError

Number of BPVs received when the DDS is set for 56K mode or the number of DDS framing errors when the DDS is set for 64K mode.

adDSUIQDiagnosticTable

n/a.

adDSUIQDiagnosticEntry

n/a

adDSUIQDiagnosticIndex

n/a.

adDSUIQDiagnosticDlci

Sets the DLCI for PVC Loopback. (Range 16 - 1007).

adDSUIQDiagnosticControl

Starts or Stops PVC Loopback Test.

adDSUIQDiagnosticDuration

Sets the Length of the PVC Loopback in minutes.

adDSUIQDiagnosticStatus

PVC Loopback Test Status. (Active/Inactive).

adDSUIQDiagnosticSecondsRemaining

PVC Loopback Test time remaining in seconds.

adDSUIQDiagnosticFramesTx

Diagnostic Frames transmitted.

adDSUIQDiagnosticFramesRx

Diagnostic Frames received.

adDSUIQDiagnosticLostFrames

Diagnostic Frames Lost.

adDSUIQDiagnosticMaxDelay

Diagnostic Maximum Delay measurement.

adDSUIQDiagnosticMinDelay

Diagnostic Minimum Delay measurement.

adDSUIQDiagnosticAvgDelay

Diagnostic Average Delay measurement.

adDSUIQDBUOption

This option specifies whether the unit automatically enters dial backup mode or waits for manual setup.

adDSUIQDBUStartLockout

This option selects the hour to begin disabling dial backup operation when daily or weekend lockout mode is active.

adDSUIQDBUEndLockout

This option selects the hour to end dial backup lockout when daily or weekend lockout mode is active.

adDSUIQDBUMode

This option specifies the dial backup operating mode for the unit as orginate or answer. One end must be set to originate and the other end to answer.

adDSUIQDBUOOS

This option enables the unit to enter backup mode if an out-of-service condition is detected from the network.

adDSUIQDBUNoRx

This option enables the unit to enter backup mode when a loss of receive signal is detected from the network.

adDSUIQDBUNoSealCurr

This option enables the unit to enter backup mode when a loss of sealing current is detected from the network.

adDSUIQDBUNoLMI

This option enables the unit to enter backup mode when network PVC signaling state goes down.

adDSUIQAutoRestoreTimer

This option selects the amount of time that the DSUIQ circuit must be active before the unit switches from backup to normal mode of operation. The timer value is in minutes from 0 to 60. A zero value disables automatic restore, DSUIQ operation must be res ...

adDSUIQRedialCount

This option allows the selection of the number of times the unit will redial the Far End unit when attempting to go to backup and a busy or reorder condition occurs. Redial count can be set for a maximum of 60.

adDSUIQDBUFailTimeout

This option allows the selection of the amount of time that the dedicated circuit failure condition is active before attempting to enter dial backup mode. The Fail Timeout value is in increments of 10 seconds up to a maximum of 600 seconds.

adDSUIQDBURedialTimer

This option works in conjunction with the Redial Counter option. The Redial Timer specifies the amount of time between redial attempts. The Redial Timer value is seconds, up to a maximum of 60 seconds.

adDSUIQDBUPassCheck

This option allows the unit to send and verify a dial backup passcode for an additional level of security. When enabled, the originate unit sends the passcode and the answer unit checks the passcode before the backup connection is considered valid.

adDSUIQDBUPassCode

This option sets the dial backup passcode used to provide an additional level of security. A passcode of one to ten digit characters can be set. If enabled, the originate unit sends the passcode and the answer unit checks the passcode to verify the conne ...

adDSUIQWeekendLockout

This option enables or disables Weekend Lockout for Dial Backup operation. If enabled, no backup will occur from midnight Friday to midnight Sunday.

adDSUIQDailyLockout

This option enables or disables Daily Lockout for Dial Backup operation. If enabled, no backup will occur between Lockout Start hour and Lockout End hour.

adDSUIQAnswerAlways

This option enables or disables Answer Always for Dial Backup operation. If enabled, the answer unit answers any incoming call regardless of failed conditions.

adDSUIQBeeperOption

This option enables or disables the audible alarm when the IQ unit goes into dial backup mode.

adDSUIQDBUPhoneNumber1

This option is used to set a phone number to place a DBU call.

adDSUIQDBUPhoneNumber2

This option is used to set a phone number to place a DBU call.

adDSUIQDBUPhoneNumber3

This option is used to set a phone number to place a DBU call.

adDSUIQDBUPhoneNumber4

This option is used to set a phone number to place a DBU call.

adDSUIQDBUPhoneNumber5

This option is used to set a phone number to place a DBU call.

adDSUIQDBUISDNSwitch

This option is used to select the ISDN switch type.

adDSUIQDBUISDNBChannelRate

This option is used to select the ISDN channel rate.

adDSUIQDBUISDNSPID

This option is used to set the SPID for the ISDN interface.

adDSUIQDBUISDNLDN

This option is used to set LDN for the ISDN interface.

adDSUIQV34LineType

This option selects the type of analog phone line.

adDSUIQDCEInterfaceType

This option enables or disables Answer Always for Dial Backup operation. If enabled, the answer unit answers any incoming call regardless of failed conditions.

adDSUIQDCEBitRate

This option is uses for utilization measurement of the DBU port when an external DCE device is used. Set this parameter in KBPS close to the connection rate.

adDSUIQIntDBUStatusTable

n/a.

adDSUIQIntDBUStatusEntry

n/a

adDSUIQIntDBUSlotIndex

n/a.

adDSUIQIntDBUFramesRx

The number of Frames the Port received for the interval.

adDSUIQIntDBUFramesTx

The number of Frames the Port transmitted for the interval.

adDSUIQIntDBUBytesRx

The number of Bytes the Port received for the interval.

adDSUIQIntDBUBytesTx

The number of Bytes the Port transmitted for the interval.

adDSUIQIntDBUAvgThruputTx

The Average Throughput the Port transmitted for the interval.

adDSUIQIntDBUAvgThruputRx

The Average Throughput the Port received for the interval.

adDSUIQIntDBUMaxThruputTx

The Maximum Throughput the Port transmitted for the interval.

adDSUIQIntDBUMaxThruputRx

The Maximum Throughput the Port received for the interval.

adDSUIQIntDBUAvgUtilizationTx

The Average Utilization the Port transmitted for the interval.

adDSUIQIntDBUAvgUtilizationRx

The Average Utilization the Port received for the interval.

adDSUIQIntDBUMaxUtilizationTx

The Maximum Utilization the Port transmitted for the interval.

adDSUIQIntDBUMaxUtilizationRx

The Maximum Utilization the Port received for the interval.

adDSUIQIntTimeInDBU

Time in seconds the DBU port was active.

adDSUIQIntDBUCrcErrors

Number of frames received with CRC errors.

adDSUIQIntDBUAbortFrames

Number of frames received without proper flag termination.

adDSUIQIntDBUOctectViolations

Number of frames received with a bit count not divisible by eigth.

adDSUIQIntDBUDiscardFrames

Number of frames discarded by the IQ unit

adDSUIQIntDBULengthErrors

Number of frames received that is less than 5 bytes or greater than 4500 bytes.

adDSUIQIntDBUEncapsulationErrors

Number of frames destined for the IQ IP stack with that does not meet the FRF.3 IA.

adDSUIQIntDBUUnroutable

Number of frames received on a management DLCI destined for the IQ unit and have the wrong IP address.

adDSUIQDayDBUStatusTable

n/a.

adDSUIQDayDBUStatusEntry

n/a

adDSUIQDayDBUSlotIndex

n/a.

adDSUIQDayDBUFramesRx

The number of Frames the Port received for the interval.

adDSUIQDayDBUFramesTx

The number of Frames the Port transmitted for the interval.

adDSUIQDayDBUBytesRx

The number of Bytes the Port received for the interval.

adDSUIQDayDBUBytesTx

The number of Bytes the Port transmitted for the interval.

adDSUIQDayDBUAvgThruputTx

The Average Throughput the Port transmitted for the interval.

adDSUIQDayDBUAvgThruputRx

The Average Throughput the Port received for the interval.

adDSUIQDayDBUMaxThruputTx

The Maximum Throughput the Port transmitted for the interval.

adDSUIQDayDBUMaxThruputRx

The Maximum Throughput the Port received for the interval.

adDSUIQDayDBUAvgUtilizationTx

The Average Utilization the Port transmitted for the interval.

adDSUIQDayDBUAvgUtilizationRx

The Average Utilization the Port received for the interval.

adDSUIQDayDBUMaxUtilizationTx

The Maximum Utilization the Port transmitted for the interval.

adDSUIQDayDBUMaxUtilizationRx

The Maximum Utilization the Port received for the interval.

adDSUIQDayTimeInDBU

Time in seconds the DBU port was active.

adDSUIQDayDBUCrcErrors

Number of frames received with CRC errors.

adDSUIQDayDBUAbortFrames

Number of frames received without proper flag termination.

adDSUIQDayDBUOctectViolations

Number of frames received with a bit count not divisible by eigth.

adDSUIQDayDBUDiscardFrames

Number of frames discarded by the IQ unit

adDSUIQDayDBULengthErrors

Number of frames received that is less than 5 bytes or greater than 4500 bytes.

adDSUIQDayDBUEncapsulationErrors

Number of frames destined for the IQ IP stack with that does not meet the FRF.3 IA.

adDSUIQDayDBUUnroutable

Number of frames received on a management DLCI destined for the IQ unit and have the wrong IP address.

adDSUIQTrapManagerTable

The trap manger route table.

adDSUIQTrapManagerEntry

n/a

adDSUIQTrapManagerRouteIndex

n/a.

adDSUIQTrapManagerRouteIPAddress

Sets the Trap Manager IP Address.

adDSUIQTrapManagerRouteDLCI

Sets the Trap Manager DLCI. (Range 16 - 1007).

adDSUIQTrapManagerRoutePort

Selects the Trap Manager Port.